One-design race shop · Dinghy
29er Race Shop
Everything you need to prepare, compete, and win.
Fit verified for 29er
All 29er equipment
24 parts
Fit verified for 29er
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for 29er
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for 29er
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for 29er
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for 29er
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for 29er
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for 29er
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for 29er
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for 29er
Ronstan
Ronstan Series 40 RTA OrbitBlock,Auto, Single, Swivel Head
Part # RONRF46100
$77.33
$90.98Fit verified for 29er
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for 29er
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for 29er
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for 29er
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for 29er
Ronstan
Ronstan Trapeze Handles, Vertical grip - Red - Pair
Part # RONRF5122R-2
$42.16
$49.60
No 29er parts match these filters.
Can’t find a part for your 29er? Request a 29er part
Go fast
29er tuning guide
The 29er is a strict one-design with non-adjustable spreaders, so tuning comes down to forestay length (rake), a mast-step chock, rig tension set with the shroud pins, jib clew hole and track pin, centreboard height and outhaul. The class and coaching guides read tension on the forestay (Loos in the coaching manual; gauge not named in the class sheet), while the original builder's manual uses an ISP gauge on both forestay and shrouds, so don't mix the numbers.
International 29er Class Association — International 29er Skiff Tuning Guide Version 2026.1 (Larry Cargill, Class Coaching and Development Manager)
- Written for
- Class one-design sails
- Tension gauge
- Not named; tension read on the forestay
- How it’s measured
- Rake is given as 'Mast Rake / Forestay Length' (445 mm in all three crew-weight tables, as printed). Centreboard figures are how far the board is raised.
- Source
- International 29er Class Association, Version 2026.1 (Larry Cargill, Class Coaching and Development Manager)
Base setup
- Forestay length (rake)
- 445 mm for all crew weights
- Chock
- 3 mm (under 100 kg and 100–120 kg crews); 3–5 mm (120+ kg)
Crew under 100 kg (forestay tension)
| Setting | 0–5 kn | 5–8 kn | 9–12 kn | 13–16 kn | 16–20 kn | 20+ kn |
|---|---|---|---|---|---|---|
| Centreboard | Down | Down | 6 cm | 12 cm | Up to mast step | Up to mast step |
| Jib clew | Top | Top | Middle | Middle | Middle | Bottom |
| Jib track | Inside/Middle | Middle | Middle | Middle | — (no setting given) | — (no setting given) |
| Forestay tension | 17 | 19 | 21 | 24 | 26 | 26 |
| Outhaul | 10 cm | 25 cm | 25 cm | 10 cm | 10 cm | 10 cm |
| Bridle | Check | Check | Check | Check | Check | Check |
Crew 100–120 kg (forestay tension)
| Setting | 0–5 kn | 5–8 kn | 9–12 kn | 13–16 kn | 16–20 kn | 20+ kn |
|---|---|---|---|---|---|---|
| Centreboard | Down | Down | Down | 10 cm | Up to mast step | Up to mast step |
| Jib clew | Top | Top | Top | Top/Middle | Middle | Middle/Bottom |
| Jib track | Inside/Middle | Middle | Middle | Middle | Outer | No pins |
| Forestay tension | 16–18 | 19 | 21 | 23 | 24–25 | 26 |
| Outhaul | 10 cm | 25 cm | 25 cm | 25 cm | 10 cm | 10 cm |
| Bridle | Check | Check | Check | Check | Check | Check |
Crew 120+ kg (forestay tension)
| Setting | 0–5 kn | 5–8 kn | 9–12 kn | 13–16 kn | 16–20 kn | 20+ kn |
|---|---|---|---|---|---|---|
| Centreboard | Down | Down | Down | Down | 10 cm | Up to mast step |
| Jib clew | Top | Top | Top | Top | Top/Middle | Middle |
| Jib track | Inside/Middle | Middle | Middle | Middle | Middle | Outer |
| Forestay tension | 16–18 | 19 | 21 | 23 | 24–25 | 26 |
| Outhaul | 10 cm | 25 cm | 25 cm | 25 cm | 10 cm | 10 cm |
| Bridle | Check | Check | Check | Check | Check | Check |
- A one-page settings sheet with no explanation; the outhaul figures (10 cm / 25 cm) are given without saying what they measure.
- In the under-100 kg table the 16–20 and 20+ kn jib-track cells are printed as a dash (no setting given); checked on the rendered PDF.
Nicky Bethwaite (Bethwaite Design / 29er class coaching manual) — 29er Coaching Manual – Section 1: Rigging for Light Air, Medium & Heavy Winds 15 December 2008
- Written for
- Class sails
- Tension gauge
- Loos (model not stated), on the forestay
- How it’s measured
- Tension read on the forestay and set with the shroud adjuster pins (pin nearer the top of the adjuster = looser). New wires can stretch 10–15 mm.
- Source
- Nicky Bethwaite (Bethwaite Design / 29er class coaching manual), 15 December 2008
Base setup
- Wind bands
- Light 2–8 kn (1–4 m/s); medium 8–15 kn (4–7 m/s); heavy 15+ kn (7+ m/s)
- No-gauge check (light setting)
- With a 73 kg (160 lb) person hanging on the trapeze wires at the bow you should just be able to pin the forestay; if not, move the shroud pins up half a hole. Come down half a hole for medium and again for heavy.
- Heel tune
- Load the aft edge of the mast base for more low-mast bend (light crews) or the forward edge for less (heavy crews); recheck rig tension after
Settings by wind (forestay tension on Loos)
| Control | Light 2–8 kn | Medium 8–15 kn | Heavy 15+ kn |
|---|---|---|---|
| Rig tension (forestay) | 18–19 | 19–21 | 21–24 |
| Jib luff | Quite soft: cloth just behind the luff tape not stretched | Quite soft: cloth just behind the luff tape not stretched | Firm, no wrinkles along the luff wire |
| Outhaul | Very light: firm, 6–7 cm (2–3") depth; above 5 kn or bumpy: 15–18 cm (6–7") | 8–10 kn: 15–18 cm depth; above that firm (6–7 cm) | Firm (6–7 cm) |
| Boom vang | No tension | Firm, just not loose with the mainsheet on | Very firm in 15–20 kn; above that ease if uncontrollable to let the main twist |
| Cunningham | No tension | None to slight, just enough to ease wrinkles | Very firm; don't ease downwind |
| Jib car | Outer pin in 2–4 kn; middle in 5–8 kn | Middle | Outer |
| Jib clew hole | Middle (lowest in very light air) | Middle | Middle (lowest in very heavy air) |
Trim by condition
- Rig tension
- The leeward side stay should not go loose when sailing.
- Jib luff
- Before leaving the shore, leave a slight bubble behind the luff wire.
- Jib sheet
- Calibrate it: 5 mm (¼") of sheet changes the jib leech noticeably.
- Light-air trim
- Bow down with the stern just skimming, boat heeled to leeward; move back as speed builds.
- Older coaching manual (2008); the class guide V2026 now uses a slightly wider tension range (16–26) and adds crew-weight tables.
- Also hosted at https://www.dinghyshop.dk/userfiles/file/tuningguides/29er_coaching_manual.pdf (not opened).
Ovington Boats (builder) — 29er Manual Rev B – Tuning Guide section Rev B, 2008
- Written for
- Class sails
- Tension gauge
- ISP rig tension gauge
- How it’s measured
- Start with the shroud pins in the highest holes, pull the mast forward with the boat-puller, pin the forestay in the middle hole of the tack fitting, then read the shrouds; lower the pins until the target is reached and record the holes.
- Source
- Ovington Boats (builder), Rev B, 2008
Base setup
- Rig tension
- 25 (ISP) on the forestay and 30 (ISP) on the shrouds
- Forestay
- Middle hole of the tack fitting; jib tack on the aft-most hole
Trim by condition
- Cunningham
- Just enough to remove the worst horizontal creases in light air, more as you become overpowered.
- Vang
- Enough to take some load off the mainsheet; not too hard or it only bends the mast.
- Outhaul
- Tight except in light wind and chop, when easing 1–2 cm helps.
- Jib track
- Outermost pins found fastest in most conditions.
- Jib clew plate
- Upper hole in light winds to keep the slot tight; lowest hole when overpowered and when learning.
- Foils
- Keep down at all times.
- An early builder manual; its ISP gauge numbers are not comparable with the Loos readings in the class guides, and its advice on board height differs from the current class guide.
- The manual notes the forestay still goes slack when the gennaker is flying.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the 29er
Technical
29er resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the 29er by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current 29er class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesApril 2026 (29er_CR_2026-04April-02.pdf)
- Class association29er.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a 29er part