One-design race shop · Dinghy
International 420 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for International 420
All International 420 equipment
18 parts
Fit verified for International 420
Optiparts
Optiparts 420 Deck Cover (Flat-Over-Deck)
Part # OPTEX2046
$430.00
Fit verified for International 420
Optiparts
Optiparts 420 Rudder Cover (Padded)
Part # OPTEX3027
$97.95
Fit verified for International 420
Nautalytics
Nautalytics Mast Mount Compass (Digital Compass)
Part # NTL-MASTMOUNT
$500.00
Fit verified for International 420
Davis Instruments
Davis Spare Vane f/WindTrak 10.Sport
Part # dav-3101
$29.99
Fit verified for International 420
Davis Instruments
Davis WindTrak 10 Sport Wind Vane
Part # dav-3120
$44.99
Fit verified for International 420
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for International 420
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for International 420
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for International 420
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for International 420
Davis Instruments
Davis Air-Flow Tels - Set of 14
Part # dav-950
$19.99
Fit verified for International 420
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for International 420
Schaefer
Schaefer Wind Indicator - Little Hawk Race
Part # SCHH007F00
$93.00
Fit verified for International 420
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for International 420
Velocitek
Velocitek Prism (Digital Dinghy Compass)
Part # VELPRISM
$579.00
Fit verified for International 420
Schaefer
Schaefer Wind Indicator - Little Hawk MK 1
Part # SCHH003F00
$34.70
No International 420 parts match these filters.
Can’t find a part for your International 420? Request a International 420 part
Go fast
International 420 tuning guide
The International 420 is tuned with rake, side-shroud tension, prebend from spreader deflection and chocks, and the mast step near the 2830 mm maximum. Gauges and datums differ a lot between guides: North and Doyle quote Loos PT-1 (31–32.5), Ullman a Loos Model A (28–30), Quantum's 2006 guide an unnamed Loos gauge (36–44), and the Superspar-gauge guides disagree with each other (Speed Sails 30–32, Super Spars 28–30, Toni Tió 24–28); rake is taken either with the halyard set at 4900 mm (or 16′ 1″) to the gooseneck band or from the masthead band to the transom.
North Sails — 420 Tuning Guide with Quick Tuning Charts (M-11 and M-7/M-9 mainsails) Charts 06/2018 update (NS Japan); page published 5 May 2017
- Written for
- North M-11, M-7 and M-9 mainsails
- Tension gauge
- Loos PT-1 (printed 'Loose PT-1'), measured with chocks in, on 2.5 mm 1x7 hard wire
- How it’s measured
- Mast step from the back of the mast groove to the back of the boat. Rake measure isn't described on the charts. Wedges are 5 mm thick.
- Source
- North Sails, Charts 06/2018 update (NS Japan); page published 5 May 2017
Base setup
- Mast step
- 2820–2830 mm (rule maximum forward 2830 mm); move back 1–3 cm if you can't get enough prebend
- Base rake
- 6110 ± 10 mm
- Base prebend
- M-11: 60–70 mm; M-7/M-9: 50–55 mm
- Base side tension
- 31–31.5 on Loos PT-1
- Spreader length
- 480 mm standard; useful range 465–495 mm (longer for heavy crews, shorter for light)
- Spreader deflection
- Adjust to get the target prebend with the step near maximum forward
M-11 mainsail quick chart (side tension Loos PT-1)
| Wind (kn) | 1–9 | 10–16 | 16–20 | 20+ |
|---|---|---|---|---|
| Shroud pin position | 1 | 2 | 3 | 4 |
| Mast rake | 6110 ± 10 mm | 6070 ± 10 mm | 6000–6040 mm | 5970–6010 mm |
| Prebend | 60–70 mm | 65–75 mm | 70–80 mm | 80 mm + |
| Side tension | 31–31.5 | 31–31.5 | 28–31 | 28–31 |
| Wedge (5 mm) | 0 (neutral) | 1–2 from neutral | 1–2 from neutral | 1–2 from neutral |
| Jib tack position | Wrinkles | A bit of wrinkles / smooth by bang on | Tight | Very tight |
| Outhaul from band (15 mm space at tack) | 20 mm | 20 mm | 5–10 mm | 0–5 mm |
M-7 / M-9 mainsail quick chart
| Wind (kn) | 1–9 | 10–16 | 16–20 | 20+ |
|---|---|---|---|---|
| Shroud pin position | 1 | 2 | 3 | 4 |
| Mast rake | 6110 ± 10 mm | 6070 ± 10 mm | 6030 ± 15 mm | 5990 ± 15 mm |
| Prebend | 45–55 mm | 45–55 mm | 45–55 mm | 55–65 mm |
| Wedge, M-7 (5 mm from neutral) | 0–0.5 | 1–2 | 1–2 | 0.5–1.5 |
| Wedge, M-9 (5 mm from neutral) | 0–0.5 | 0.5–1.5 | 0.5–1.5 | 0–1 |
| Jib tack position | Wrinkles | Smooth | Tight | Very tight |
| Outhaul from band, M-7 (10 mm space at tack) | 25 mm | 25 mm | 25 mm | 15 mm |
| Outhaul from band, M-9 (10 mm space at tack) | 10–15 mm | 10–15 mm | 5–15 mm | 0–10 mm |
Trim by condition
- Prebend choice
- Heavier crews and softer masts want less prebend; lighter crews and stiffer masts more. Test in 5 mm steps within the chart range.
- Chocks
- In a breeze chock quite hard, because you'll be using a lot of vang.
- Jib cunningham
- None until overpowered, then progressively; very hard in strong wind (a foot loop helps).
- Windward sheet
- Use it to hold the jib leech at the right inboard position; mark the sheet at the cleat.
- Jib height
- With a fixed sheeting point, adjust the peak rope to move the clew up or down and get the right lead angle; it interacts with rake.
- Spinnaker pole
- In chop on a flat run, set the tack slightly lower than the clew.
- Centreboard
- Play it actively; pack the slot so it moves easily.
- Chart cells that span columns in the PDFs are repeated in each column here (M-11 side tension, wedge and outhaul; M-7/M-9 prebend and outhaul); spans were checked against the rendered charts.
- The M-7/M-9 chart gives side tension only as the base value (31–31.5).
- Charts: https://cdn.shopify.com/s/files/1/0688/6549/1220/files/NorthSails-420-QuickTuningChart-M11-1.pdf and https://cdn.shopify.com/s/files/1/0688/6549/1220/files/NorthSails-420-QuickTuningChart-M7-M9-1.pdf
Doyle Sails — International 420 Class Tuning Guide September 2025 (PDF dated 5 Sep 2025)
- Written for
- Doyle CM 19 and CM 24/25 mainsails, CJ 24 jib, CS 24 spinnaker
- Tension gauge
- Loos PT-1M; place it at the same height each time (500 mm above deck is a good target); numbers can vary between gauges
- How it’s measured
- Pull the halyard to the masthead and set it so the tape reads 4900 mm at the top of the gooseneck black band, then measure to the transom face, top middle. Prebend: main halyard held tight at the gooseneck band, mast track to the forward edge of the halyard at the spreaders.
- Source
- Doyle Sails, September 2025 (PDF dated 5 Sep 2025)
Base setup
- Rake tolerance
- ± 10 mm
CM 19 mainsail gears (tension on Loos PT-1M)
| Gear | Wind | Rake | Prebend | Tension |
|---|---|---|---|---|
| 1 | 0–12 kn | 6110 | 55 mm | 31.5 |
| 2 | 9–16 kn | 6080 | 55 mm | 32 |
| 3 | 14–20 kn | 6040 | 55 mm | 32 |
| 4 | 17–24 kn | 6010 | 60–70 mm | 32 |
| 5 | Dogs off chains | 5980 | 65–75 mm | 32.5 |
CM 24/25 mainsail gears (tension on Loos PT-1M)
| Gear | Wind | Rake | Prebend | Tension |
|---|---|---|---|---|
| 1 | 0–12 kn | 6110 | 60–65 mm | 31.5 |
| 2 | 9–16 kn | 6080 | 60–65 mm | 32 |
| 3 | 14–20 kn | 6040 | 60–65 mm | 32 |
| 4 | 17–24 kn | 6010 | 65–75 mm | 32 |
| 5 | Dogs off chains | 5980 | 70–80 mm | 32.5 |
Trim by condition
- Prebend in gears 4–5
- There's a 10 mm spread: lighter teams or waves want more prebend (less vang, more twist); heavier teams who can hold a tighter leech want a straighter mast.
- Top batten
- RBS rocket tensioner: just remove the wrinkles beside the pocket as the base; half a turn may be the whole loose-to-tight range; ease a full turn for storage.
- Jib height
- Foot just kissing the deck at its lowest point with no jib cunningham on. The CJ 24's clew attachment is slightly higher, so less windward sheeting is needed for the same closed leech.
- Spinnaker
- Match the leeward clew height with the pole clew; lower in light air, higher when windy. The foot folds on very tight reaches by design.
- The November 2023 edition (https://www.doylesails.com/wp-content/uploads/2023/11/Doyle-Sails-420-Tuning-Guide.pdf) prints gear 5 rake as 5090 for both mains (5980 in the 2025 edition), lists the second main as CM 24 only with 60 mm prebend in gears 1–3, and omits 'to the transom face' from the rake method.
- Doyle contact on the guide: Andrew Brown (Doyle One Design expert, doylesails.co.nz).
Ullman Sails — 420 Racing Guide Version 2.0 (PDF Feb 2016; same rig numbers as the 2008 420 Tuning Guide)
- Written for
- Not stated (Ullman Sails guide; mentions the Ullman jib's sewn-on leech telltale); written for the Proctor Kappa mast, also a benchmark for Superspar M7
- Tension gauge
- Loos & Co Model A for shroud and jib-wire tension
- How it’s measured
- Mast foot from the centreboard pin to the middle of the mast section. Rake is given as two numbers (e.g. 609 cm / 120 cm); the second reference isn't explained.
- Source
- Ullman Sails, Version 2.0 (PDF Feb 2016; same rig numbers as the 2008 420 Tuning Guide)
Rig by wind (tension on Loos Model A)
| Wind (kn) | 0–6 | 7–11 | 12–15 | 16–19 | 20+ |
|---|---|---|---|---|---|
| Mast foot position | 42 cm | 42 cm | 43 cm | 43.5 cm | 44 cm |
| Shroud tension | 28 | 30 | 30 | 29 | 29 |
| Spreader length | 46–48 | 46–48 | 46–48 | 46–48 | 46–48 |
| Prebend | 3.5 cm | 3 cm | 3 cm | 3 cm | 3 cm |
| Mast rake | 609 cm / 120 cm | 607 cm / 118 cm | 605 cm / 116 cm | 602 cm / 112 cm | 597 cm / 107 cm |
| Jib wire tension | 21 | 21 | 20 | 18 | 16 |
Controls by wind
| Wind (kn) | 0–6 | 7–11 | 12–15 | 16–19 | 20+ |
|---|---|---|---|---|---|
| Centreboard | Angled forward | Normal / vertical | Lift a little | Raise | Raise a lot |
| Chocks | 0 / -1 | 0 | 1 / 2 / 3 | 2 | 1 |
| Kicker | Slack | Take up slack | Ease on (start applying) | Pull hard | Pull hard or open |
| Cunningham | None | None | Lighter teams use | Pull | Pull hard |
| Barber hauler | None | None | Pull | Pull harder | Ease |
Trim by condition
- Mast foot
- If the boat turns into the wind quickly the mast is too far aft; move it forward slightly, and vice versa.
- Top batten
- Maximum tension in light–medium air; medium in heavy air; a stiffer batten is quicker above 18 kn.
- Mainsheet
- Keep the aft end of the top batten between 5° inside and 10° outside parallel to the boom: open 5–10° in light air and chop, parallel to 5° to windward in medium for power, then use it for twist once overpowered.
- Bridle
- As long as possible while allowing 4–6 cm of over-trim before blocks meet.
- Jib
- Trim so the leech telltale is on the verge of stalling, except in very light air, chop, out of tacks and off the line. Foot just touching the deck.
- The 2008 edition is at https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-420-Tuning-Guide-2008.pdf.
- Spreader length has no unit in the source (46–48, presumably cm).
- Loos Model A readings are not comparable with the PT-1 numbers in the North and Doyle guides.
Speed Sails (Sailboats) — 420 Tuning Guide by Sailboats Speedsails Undated
- Written for
- Not stated (Speedsails guide); spar settings for Superspar and Proctor Kappa
- Tension gauge
- Superspar tension gauge on the shroud (30 ≈ 400 lb, 32 ≈ 470 lb)
- How it’s measured
- Jib hoisted at 400 lb, no chocks; tape on the main halyard reading 16′ 1″ to the top of the gooseneck black band, then swing to the top of the transom.
- Source
- Speed Sails (Sailboats), Undated
Base setup
- Spreader length
- 470 mm (heavy crews 480 mm); Superspar and Proctor Kappa
- Spreader deflection
- Superspar 160 mm; Proctor Kappa 155 mm (only a guide to prebend)
- Rig tension
- About 400 lb (30) in light winds, up to about 470 lb (32) in heavier winds
- Rake
- Under 15 kn 19′ 10½″–19′ 11¾″ (400 lb); over 15 kn 19′ 8½″–19′ 9″ (470 lb)
Settings by wind (rig tension on Superspar gauge)
| Wind (kn) | 0–5 | 5–10 | 10–18 | 18+ |
|---|---|---|---|---|
| Mast rake | 19′ 11¾″ | 19′ 11″ | 19′ 10½″ | 19′ 9″ / 19′ 8″ |
| Chocks | 0 | 1 (neutral) | 2 (straighter than neutral) | 1 (back to neutral) |
| Centreboard | Angled forward | Leading edge vertical | Lift as you start planing | Raised – not more than 6″ |
| Kicker | Slack | Take up slack | Begin to apply | Pull hard |
| Cunningham | None | None | Begin to apply | Pull hard |
| Barber hauler | None | 2–3″ | 2–3″, ease as overpowered | None |
| Rig tension | 30 | 30 | 31 | 32 |
Trim by condition
- Chocks
- 0–5 kn none with the crew to leeward (bends the lower mast); 5–10 kn one chock filling the neutral gap; 10–18 kn a second chock when fully trapezing; 18+ back to one to let the mast bend.
- Centreboard
- Raise up to 3″ in flat water and up to 6″ in rough seas.
- Outhaul
- Tight upwind almost always; ease up to 1″ only in moderate chop; 1½–2″ downwind.
- Kicker
- Slack out until overpowered, then enough to keep the top telltale flying about 80%.
- Cunningham
- From 18 kn, gradually.
- Barber hauler
- None 0–6 kn; pull in 2–3″ with the sheet tight at 6–18 kn; ease off above 18 kn.
- Spinnaker
- Head 2–3″ off the mast (stopper knot); keep clews level; lower the pole in very light air.
- The 0–5 kn rake (19′ 11¾″) sits at the top of the prose range for under 15 kn.
- Wind bands differ inside the guide: the summary table uses 0–5 / 5–10 / 10–18 / 18+ kn while the barber-hauler prose uses 0–6 / 6–18 / 18+ kn.
Quantum Sails (Quantum Sail Design Group WA) — International 420 Class Tuning Guide PDF dated Nov 2006; produced by Paul Eldrid
- Written for
- Quantum International 420 sails
- Tension gauge
- Loos tension gauge (printed 'Loose'), model not stated
- How it’s measured
- Mast step from the inside of the transom to the pin at the aft of the mast heel. Rake: lock the halyard with the tape reading 4900 mm to the top of the gooseneck black band, then measure to the transom. Spreader length L: side of mast to sidestay; poke P: top batten across the shrouds at the spreader tips to the back of the mast. Bend: main halyard to the gooseneck, aft face of mast to halyard at spreader height.
- Source
- Quantum Sails (Quantum Sail Design Group WA), PDF dated Nov 2006; produced by Paul Eldrid
Base setup
- Mast step
- 2790–2810 mm
- Spreaders, crew 115–125 kg (L / P, mm)
- Proctor Kappa 470 / 125; Superspar M7 460 / 135; Proctor Stratus 450 / 145
- Spreaders, crew 125+ kg (L / P, mm)
- Proctor Kappa 480 / 115; Superspar M7 470 / 120; Proctor Stratus 465 / 125
- Calibration
- No chocks, about 40 on the gauge: rake should read 19′ 10½″ to 20′ 0″; adjust chainplate holes if not
- Bend check
- At least 30 mm of bend at the most upright rake with no chocks (otherwise wind the spreaders back a little); for 5–12 kn add chocks until about 10 mm of bend remains
Approximate settings, crew 115–125 kg (tension on Loos gauge)
| Wind (kn) | Tension | Rake | Chocks (example) |
|---|---|---|---|
| 0–5 | 43 | 20′ 0″ | 0 |
| 5–12 | 41 | 19′ 11½″ | 6 |
| 12–15 | 40 | 19′ 10½″ | 5 |
| 15–20 | 39 | 19′ 9½″ | 4 |
| 20–25 | 37 | 19′ 9″ | 3 |
| 25+ | 36 | 19′ 8½″ | 2 |
Approximate settings, crew 125+ kg (tension on Loos gauge)
| Wind (kn) | Tension | Rake | Chocks (example) |
|---|---|---|---|
| 0–5 | 44 | 20′ 1″ | 0 |
| 5–12 | 44 | 20′ 1″ | 6 |
| 12–15 | 41 | 19′ 11½″ | 6 |
| 15–20 | 39 | 19′ 10½″ | 5 |
| 20–25 | 37 | 19′ 9½″ | 4 |
| 25+ | 36 | 19′ 9″ | 3 |
Centreboard (marks: 8 = fully down, then 7, 6, 5 at 30 mm steps up)
| Wind (kn) | 0–14 | 14–18 | 18–22 |
|---|---|---|---|
| Board mark | 8 | 7–6 | 6–5+ |
Trim by condition
- Top batten
- Just enough to remove pocket wrinkles until about 15 kn, then quite firm.
- Outhaul
- Firm in light air; eased a little in medium so the foot shelf just opens; very tight in heavy air.
- Cunningham
- Light: just remove the major wrinkles; medium: most wrinkles; heavy: tight to very tight.
- Mainsheet
- Top ribbon flowing at least 50% of the time in light air, about 70% in medium; vang-sheet in heavy air.
- Vang
- Off in light air; none in medium until you ease to depower; then progressively more in heavy air to control twist and help bend.
- Jib
- Tack no more than 40 mm above the deck at the forestay fitting; luff tension just removes wrinkles (off in very light air, lots in heavy). Barber-haul in all but heavy air: eased sheet in light air, sheet firm and barber-hauler very tight in medium (telltales flowing about 90% of the time), progressively less as you vang-sheet in heavy air.
- In the settings charts only tension and rake are printed as Quantum's 'approximate settings'; the chainplate (F4), hook and chock entries are handwritten sample fill-ins, and the guide says to calibrate chocks yourself (steps 6–7). Chock values are shown only as that example.
- Older edition (2006) that predates current 420 mainsail designs; copy hosted by a Japanese club (wakayama-sailing.org) and linked from the International 420 class's tuning-guides page.
Toni Tió Velas — 420 Trimming Notes (420 sail trim and tuning guide) Undated; PDF created Jan 2004
- Written for
- Toni Tió 420 sails
- Tension gauge
- Superspar gauge (kg and lb equivalents also given)
- How it’s measured
- Mast step measured from the stern. Spreader length: mast side wall to shroud; deflection: line joining the shrouds to the aft face of the mast. Rake: with chocks in and jib tension set for the conditions, tape on the main halyard hoisted to the highest point the mainsail may be set, measured to the top centre of the transom.
- Source
- Toni Tió Velas, Undated; PDF created Jan 2004
Base setup
- Mast step
- 2.83–2.88 m from the stern; further forward in strong wind
- Spreader length
- 48 cm a good length (the guide also mentions 45 cm for light and 50 cm for heavy crews)
- Spreader deflection
- 15–17 (unit not stated) for Proctor and Superspar masts
- Chocks
- 15 mm each
Rig tension (Superspar gauge)
| Wind (kn) | Load | Superspar gauge |
|---|---|---|
| 0–6 | 123 kg / 270 lb | 24 |
| 6–10 | 136 kg / 300 lb | 26 |
| 10–20 | 155 kg / 340 lb | 28 |
| 20+ | 136 kg / 300 lb | 26 |
Chocks
| Wind (kn) | 0–6 | 6–10 | 10–14 | 14–20 | 20+ |
|---|---|---|---|---|---|
| Chocks | 0 | 2 | 2–3 | 1–2 | 1 |
Mast rake
| Wind (kn) | 0–10 | 10–18 | 18+ |
|---|---|---|---|
| Rake | 6.06 m | 6.03 m | 5.97 m |
Trim by condition
- Rake
- More rake needs more shroud tension so the forestay doesn't slacken.
- Cunningham
- Loose in light air (ignore small horizontal creases), tightened gradually as it builds.
- Foot
- Fairly tight in flat water, slacker in waves for power, quite loose off the wind.
- Kicker
- The main leech control on a 420; tighten progressively, fitting chocks first if needed.
- Top batten
- Adjustable and firm: light tension in light air, firmer in a breeze.
- Jib height
- Set rake and tension, lay the boat on its side and set the jib so the foot lightly touches the deck; with more rake set the jib a little higher.
- Barber hauler
- The fixed fairleads are at least 1250 mm apart, so the jib is quite open; barber-haul to close it, but over-pulling backwinds the main.
- Older Spanish sailmaker's notes (c. 2004); the spreader-length sentence is garbled in the source, so only the stated 48 cm recommendation is firm.
- Superspar-gauge readings here (24–28) are lower than in the Speed Sails guide (30–32) for similar loads; gauges and wire may differ.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
International 420 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the International 420 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current International 420 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesCurrent class rules
- Class association420sailing.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a International 420 part