One-design race shop · Multihull
Nacra 17 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Nacra 17
All Nacra 17 equipment
42 parts
Fit verified for Nacra 17
Harken
Harken Block - Carbo 57mm 5-Sheave - Swivel
Part # HAR2762
$238.95
$271.30Fit verified for Nacra 17
Harken
Harken Block - Wire High Strength 25mm - Wire
Part # HAR300
$47.95
$54.10Fit verified for Nacra 17
Harken
Harken Swivel Cam Cleat - Base (Micro) w/ Cam-Matic 468 & Sheaves: 5/8 in (16 mm) - Line: 3/32 to 1/4 in (2 to 6 mm) - 60 mm Height
Part # HAR9051
$122.95
$139.10Fit verified for Nacra 17
Harken
Harken Block - 16mm Single - Eyestrap Assembly
Part # HAR442
$26.95
$30.45Fit verified for Nacra 17
Harken
Harken Canvas Nacra 17 Boom, Tiller & Cross Bar Bag
Part # HAC8712
$126.95
Fit verified for Nacra 17
Harken
Harken Canvas Nacra 17 Mast w/ Shroud Cover (Zippered)
Part # HAC8707
$602.20
Fit verified for Nacra 17
Harken
Harken Block - Carbo 29mm Single - Pivoting / 468 Cam-Matic
Part # HAR395
$78.95
$89.10Fit verified for Nacra 17
Harken
Harken Canvas Nacra 17 Yard Cover - Mast-up Sailboat Cover
Part # HAC8713
$1,679.10
Fit verified for Nacra 17
Harken
Harken Traveler Car 7/8 in (22.0 mm) - High-Load 1250 - Pivoting Sheaves, Eyestrap
Part # HAR2765
$369.95
$420.30Fit verified for Nacra 17
Harken
Harken Sheave - Sheave Dia: 5/8 in (16.0 mm)
Part # HAR415
$12.95
$14.75Fit verified for Nacra 17
Harken
Harken Block - Carbo 57mm 5-Sheaves - Ratchet - w/ 40mm Side Carbos / 150 Cam-Matic
Part # HARHC8454
$351.00
$487.40Fit verified for Nacra 17
Harken
Harken Canvas Nacra 17 Travel / Hull Cover (Set)
Part # HAC8706
$1,255.10
Fit verified for Nacra 17
Harken
Harken Micro Sheave - Sheave Dia: 7/8 in (22.0 mm)
Part # HAR277
$5.95
$6.60Fit verified for Nacra 17
Harken
Harken Canvas Nacra 17 Yard Cover (Sunbrella)
Part # HAC8713A
$1,894.65
Fit verified for Nacra 17
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 w/ Wire Fairlead 475 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR469
$45.95
$51.55Fit verified for Nacra 17
Spinlock
Spinlock Cam Cleat - PXR (Centre Pivot) - Single - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # SPI-PXR0206-VP
$73.74
$86.75Fit verified for Nacra 17
Harken
Harken Micro Sheave - Bullet - Sheave Dia: 1 1/8 in (29.0 mm)
Part # HAR160
$13.95
$16.15Fit verified for Nacra 17
C. Sherman Johnson
C. Sherman Johnson Rigging Tape - White - 1" x 15'
Part # CSJ-50-115
$24.30
$25.25Fit verified for Nacra 17
C. Sherman Johnson
C. Sherman Johnson Rigging Tape - Black - 1" x 15'
Part # CSJ-50-115B
$24.30
$25.25Fit verified for Nacra 17
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR468
$36.95
$41.50Fit verified for Nacra 17
Harken
Harken Block - Carbo 29mm Single - Fixed Head
Part # HAR348
$17.95
$19.90Fit verified for Nacra 17
Harken
Harken Traveler Car 1/2 in (13.0 mm) Micro - Pivoting Shackle
Part # HAR2700
$150.95
$171.00Fit verified for Nacra 17
Harken
Harken Block - Carbo 40mm Single - Pivoting / 150 Cam-Matic
Part # HAR2156
$89.95
$102.20Fit verified for Nacra 17
Harken
Harken Block - Carbo 29mm Single - Stand-Up - Fixed Head
Part # HAR349
$26.95
$30.95Fit verified for Nacra 17
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Nacra 17
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Nacra 17
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for Nacra 17
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Nacra 17
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for Nacra 17
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Nacra 17
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Nacra 17 parts match these filters.
Can’t find a part for your Nacra 17? Request a Nacra 17 part
Official Harken dealer
Nacra 17 deck layout
- Hull Length
- 5.25 m
- Beam
- 2.59 m
- Mast Length
- 9.00 m
- Total upwind sail area
- 20.10 m²
- Spi Area
- 19.00 m²
- Average crew weight
- ±135 kg
- Overall weight excl. sails
- 138 kg
Mainsheet
-
1
57mm 5-Sheave Block — SwivelHarken 2762
$238.95 -
2
25mm Wire Block — ShackleHarken 300
$47.95 -
3
25mm Wire Block — ShackleHarken 300
$47.95 -
4
29mm Pivoting Lead Block — Cam-Matic® cleatHarken 395
$78.95 -
5
18mm Fly Soft-Attach Double BlockHarken 2158
$42.95 -
8
22mm Micro SheaveHarken 277
$5.95 -
10
57mm Triple Ratchet Block — Swivel, 40 mm Side Carbos, Cam CleatHarken HC8454
$351.00
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Nacra 17 tuning guide
The Nacra 17 is tuned in four modes rather than plain wind bands (both hulls in, popping, foiling, overpowered): rake is set on the forestay and checked with crew on the trapeze, shroud tension rises from about 25–30 to 35–40 on a Loos gauge, diamonds are added in millimetres from base, and daggerboard/rudder angles change with each mode. The class association's own guide is the only published one; one-design sails mean there are no competing sailmaker guides.
Nacra 17 Class Association — Nacra 17 Tuning Guide (Nacra 17 platform setup) Current class page (rig table image dated December 2025; platform data 2022–2023 Worlds)
- Written for
- One-design Nacra 17 main and jib (foiling, post-2017 boats)
- Tension gauge
- Loos tension gauge ('loose gauge'), model not stated; shroud figures in lb
- How it’s measured
- Rake is set with the forestay length, then shroud tension. Base rake is measured with the crew on trapeze to leeward and 30 lb on the shrouds, as the difference between the distances to the bow and to the stern (check both sides). For the two windier settings stop using the gauge and add 8 mm (10 mm for high wind) at the shroud adjusters. Diamonds are tracked from base with a fixed measurement sticker on the mast. Spreader rake is measured from a line between the spreader tips to the trailing edge of the mast.
- Source
- Nacra 17 Class Association, Current class page (rig table image dated December 2025; platform data 2022–2023 Worlds)
Base setup
- Base rake check
- Crew on trapeze to leeward, 30 lb on the shrouds (Loos), measure bow-minus-stern difference; 13 cm difference in the two lighter modes
- Diamonds (base)
- 30 lb on the Loos gauge
- Spreaders
- Set at base (the class says it doesn't matter much); less spreader rake for a soft mast or a heavy team
- Foiling threshold
- Don't try to take off below 10.8 kn of boat speed; once foiling you can stay up down to about 10 kn
- Platform: bow to bow
- Average 2178 mm (2022), 2177 mm (2023), centreline of each bow at chine height
- Platform: transom to transom
- Average 2191 mm (2022), 2193 mm (2023)
- Toe in/out
- 10 mm (2022 and 2023), boards fully down at zero rake
- Lower bearing to lower bearing (aft)
- 2264 mm (2022)
- Daggerboard tip to tip
- 860 mm (2022), 857 mm (2023), light inward pressure
- Rudder rake range
- 4° (4.05° max)
- Elevator angle of attack (starting point)
- 3.6° to −0.4°; flat water might use −0.3° as the farthest-aft elevator position, waves and wind −0.5°
- Front beam pre-bend option
- About half the intended amount, e.g. 5 mm
Rig settings by mode (shroud tension on Loos gauge, lb)
| Setting | 0–6 kn (2 hulls in) | 6–8 kn (marginal and popping) | 10–16 kn (foiling) | 16+ kn (overpowered) |
|---|---|---|---|---|
| Shroud tension (Loos) | 25–27 | 30–35 | 35 | 35–40 |
| Rake (mm difference) | 13 cm diff | 13 cm diff | Forestay +8 mm | Forestay +10+ mm |
| Diamond tension (Loos + mm) | Base (30 lb) | Base to +3 mm | +10 to 20 mm | +15–20 mm |
| Diamond angle (mm) | 58 (spans the first three modes) | 58 | 58 | 62 |
| Rotation | To skipper trap | Outer bolt on rear beam | Between outer bolt and internal (red) | Between outer bolt and internal (red) |
Foil settings by mode (degrees)
| Setting | 0–6 kn (2 hulls in) | 6–8 kn (marginal and popping) | 10–16 kn (foiling) | 16+ kn (overpowered) |
|---|---|---|---|---|
| Leeward board | 2 | 2 to 3 | 2 to 3 | 2 to 3 |
| Windward board | 2 | 2 to 3 | −1 to −2 | −2 to max |
| Downwind | 2 | 6 down to 5 foiling | 4 down to 3 | 2.7 to 3.5 |
| Rudders (differential) | 5 mm (low drag) | 5 mm (low drag) | Max diff | −2 degrees |
Jib and mainsail settings by mode
| Setting | 0–6 kn (2 hulls in) | 6–8 kn (marginal and popping) | 10–16 kn (foiling) | 16+ kn (overpowered) |
|---|---|---|---|---|
| Jib halyard position | Set so the tack is at the pole at max cunningham | Same | Same | Not given (blank in source) |
| Jib clew board | Top | Middle | Middle | Middle |
| Jib track | At the pin | 1 cm out | 2–3 cm out | Max out −1 mm |
| Cunningham | As little as possible | As little as possible | Full | Full |
| Jib battens | Most flexible | Most flexible | Mid flex | Least flexible |
Trim by condition
- Shrouds (text)
- Two hulls in the water about 25; move to 27 as soon as you can pop a hull; 35 once foiling.
- Diamonds and cunningham
- Work them together: diamonds flatten the middle of the main, cunningham flattens and pulls draft forward. The first few mm of diamond stiffen the mast; there's a big jump (10–20 mm, depending on mast, main and gustiness) at the switch to foiling, when cunningham goes on, or rotation drifts to the middle. Too much cunningham = draft too far forward; too much diamond = can't adapt to lulls; too little of both = mainsheet too far out.
- Foils
- More rudder lift = less pitch control from body weight; set to suit style and waves. Bow-down trim needs more board angle, bow-up less. Move the leeward board to 4° early when preparing to foil. Upwind foiling: rudders to max differential, board differential only if the set-up is stable. Light wind both rudders about 2°; upwind foiling leeward rudder max lift, windward zero.
- Mainsail
- Batten tension is a key tuning tool: loosen until they wiggle to depower, tighter to power up (until they go out of vertical alignment). Outhaul can be left fixed. Mark a safe max cunningham on each mast; it differs by 1–2 cm between a new and an old main.
- Platform
- Get hulls parallel, vertical and level with a water level before anything else; tape the rudder box so the rudder sits identically every time; 0.2° of elevator angle matters.
- Mast check
- If the boat feels wrong, have a coach check mast straightness against other boats first.
- The text gives shroud tensions of 25 / 27 / 35 lb for two hulls, popping and foiling, while the table shows 25–27 / 30–35 / 35 / 35–40.
- The diamond-angle and rotation rows use merged cells in the source image; we've repeated the value across the modes it spans.
- The page's wind bands skip 8–10 kn (6–8 then 10–16), as published.
- The rig table gives the windy-mode rake as 'forestay +8 mm / +10+ mm', while the text says to add 8 mm (10 mm for high wind) at the shroud adjusters.
- The jib-halyard rule in the jib table spans the first three modes; the 16+ cell is blank.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the Nacra 17
Technical
Nacra 17 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Nacra 17 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Nacra 17 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesNacra 17 Class Rules, effective date 26th March 2026 (v.2), Status: Approved
- Class associationnacra17.org
- Builder specificationsNacra 17 on nacrasailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Nacra 17 part