One-design race shop · Dinghy

Fireball Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Fireball

  • 14 verified parts
  • 7 brands
  • Fit checked Nov 2026

Fit verified for Fireball

All Fireball equipment

14 parts

Can’t find a part for your Fireball? Request a Fireball part

Go fast

Fireball tuning guide

Fireballs are tuned by rake (roughly 22′ 8″ down to 22′ 2″ to the top of the transom), jib-luff rig tension, spreaders for 25–30 mm of prebend, strut/chocks, jib fairlead in/out and height, and centreboard rake. Tension is quoted either in lb on the jib luff or as a Loos gauge reading (27–32), which are different scales, so stick to the gauge your guide uses.

North Sails — Fireball Tuning Guide (T-10) Posted 20 Aug 2024

Written for
North T-10 mainsail and matching jib; Cumulus or M7 mast
Tension gauge
Not named; lb (and kg) on the forestay/jib luff
How it’s measured
Prebend with the rig tensioned at the stated rake. Fairlead piston height uses North's #1–#7 fairlead guide; #3–4 lines up with the middle line drawn on the jib clew.
Source
North Sails, Posted 20 Aug 2024

Base setup

Prebend
25–30 mm with 22′ 6″ rake and 400 lb on the forestay
Prebend alternative
Set 25–30 mm at 22′ 8″ and wind the spreaders forward one full turn when raking back to 22′ 6″
Spreader length
390–425 mm (Cumulus/M7)
Spreaders by crew weight
Helm 60–70 kg: crew over 82 kg use 425 mm; shorten 10 mm per 10 kg less crew weight (some light teams use 390 mm); heavy crews may also shorten in winds gusting over 30 kn
Jib tack
75 mm above the deck (level with the top of the luff-wire swage eye)

Tuning matrix (rig tension in lb on the forestay)

Wind & sea1–5 kn flat1–5 kn choppy6–10 kn flat6–10 kn choppy11–15 kn flat11–15 kn choppy16–21 kn22+ kn
Mast rake22′ 7″ / 22′ 8″ (6875–6910 mm)22′ 7″ / 22′ 8″ (6875–6910 mm)22′ 8″ (6910 mm)22′ 8″ (6910 mm)22′ 6″ (6850 mm)22′ 6″ (6850 mm)22′ 6″ / 22′ 2″ (6850–6750 mm)22′ 6″ / 22′ 2″ (6850–6750 mm)
Rig tension400 lb (182 kg)400 lb (182 kg)400 lb400 lb400 lb400 lb400 lb360 lb
KickerNone (set for the run)None (set for the run)Hold leech tension when the sheet is easedHold leech tension when the sheet is easedUntil 2nd telltale stalls 25% of the timeUntil 2nd telltale stalls 25% of the timeOn hardFull on (ease if the boom catches the water)
Strut at deck (from neutral)Ease 5 mm00000Ease 5 mmEase 5–10 mm
OuthaulFull onEase 20 mmFull onEase 20 mmFull onFull onFull onFull on
CunninghamNoneNoneNoneNoneSee notesSee notesSee notesSee notes
Jib fairleads from centreline230–250 mm230–250 mm230–250 mm250 mm250–270 mm250–270 mm270–280 mm280–300 mm
Fairlead piston height#1#1#1#2–3#2–3#4#5–7#5–7
CentreboardForward 1″VerticalVertical – raised 2″Vertical – raised 2″Raise 3–5″Raise 3–5″Raise 5–6″Raise 6–8″

Fairlead height above max-down by wind

WindRaiseFairlead guide position
15 kn20–40 mm#5
20 kn40–60 mm#5 or #6
25 kn60–80 mm#6
Extreme80–100 mm#6 or #7

Trim by condition

Rake changes
Upright rake (22′ 7″/8″) up to 10 kn; 22′ 6″ in 11–15 kn once the boom can't stay between centreline and halfway to the gunwale; hold 22′ 6″ with kicker and cunningham; go to 22′ 4″ when the boom lives between halfway and the gunwale (probably 20+ kn); light crews can use 22′ 2″ in extreme conditions.
Cunningham (T-10)
Lots of kicker pulls the draft aft; cunningham brings it back and bends the mast. Pull it to remove wrinkles, then a further 40–50 mm; in Force 3–4 add 2–3 cm more each time it feels overpowered, before reaching for more rake.
Prebend by venue
Open water and crews of 86 kg+: set 25–30 mm at 22′ 6″ and leave spreaders alone at 22′ 7″/8″ so prebend drops to about 15 mm. Inland water: more prebend up to 10 kn (use the alternative spreader setting).
Fairlead in/out
Boom on centreline 230 mm; centreline to halfway 250 mm; halfway to gunwale 270–280 mm; around the gunwale with max rake/bend/kicker 300 mm.
Fairlead height
Below 8 kn start at max height (#1), lower to max down (#4) once the crew can straighten their legs on the wire; stay there until the leads are out at 270 mm, then raise in 20 mm steps.
Jib sheet
Easy to under-sheet once trapezing: sheet until the foot goes tight or backwinding below the spreaders becomes excessive. In 12–15 kn prefer #5 with more sheet over #4 with less; sheet harder if there's weather helm with the main set right.
Gusty offshore flat water
Use less kicker so the boom can stay inside the gunwale in gusts.
Chocks/strut
If in doubt, neutral.
  • The guide is written in the first person. Its fairlead and jib-sheet notes reappear word-for-word in a 'Fireball jib control by North Sails (Tim Rush)' sheet hosted by the Swiss Fireball gazette (https://wl48www394.webland.ch/gazette/TRIMM/Fireball%20jib%20control%20by%20North%20Sails.pdf).
  • Matrix cells that span several columns in the PDF are repeated in each column here.
  • Rig tension is given as lb on the forestay; P&B and Hyde give Loos gauge readings on the jib luff instead.

Pinnell & Bax — Fireball Tuning Guide 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-FB)

Written for
P&B Fireball sails; Cumulus / M7 mast; crew weight 81–85 kg
Tension gauge
Loos gauge on the jib luff (model not named)
How it’s measured
Hoist the tape so it reads 19′ 8″ to the top of the black band at the gooseneck, then read rake at the top of the transom. Prebend: rig tension on, main halyard tight to the gooseneck, distance at spreader height from mast track to halyard. Spreader A: from the line between spreader ends perpendicular to the mast track; B: mast side wall to spreader end.
Source
Pinnell & Bax, 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-FB)

Base setup

Prebend datum
25 mm at spreader height
Spreaders, 24 stone
A 160 mm / B 410 mm
Spreaders, 26 stone
A 175 mm / B 420 mm
Spreaders, 28+ stone
A 180 mm / B 425 mm
Spreaders (diagram)
A 160 mm / B 420 mm

Settings by wind and sea (rig tension on jib luff, Loos)

Wind & sea1–4 flat1–4 choppy5–9 flat5–9 choppy10–15 flat10–15 choppy16–2021+
Mast rake22′ 6″ / 6908 mm22′ 8″ / 6900 mm22′ 6″ / 6900 mm22′ 6″ / 6900 mm22′ 4″ / 6850 mm22′ 4″ / 6820 mm22′ 2″ / 6810 mm22′ 2″ / 6810 mm
Rig tension (jib luff, Loos)29¾29¾29¾3030313232
KickerNoneNoneA bitA bit––LoadsLoads
Kicker reason––Top telltales stalling 30%Top telltales stalling 30%Top telltales stalling 30%Top telltales stalling 30%Control twist, blade out the mainControl twist, blade out the main
CunninghamNoneNoneNoneNoneNoneNoneYesYes – a lot
Jib fairlead (line)Lower lineMiddle lineLower lineTop lineMiddle lineTop lineTop lineTop line
Jib fairlead from centreline260 mm260 mm260 mm265 mm265–270 mm265–270 mm275–300 mm300 mm
Jib sheetNormalEase 0.5 cmNormalNormalNormalNormalEase 0.5–1.5 cmEase 1.5–2 cm
Strut (from neutral)0000–0.5 cm00–1.5 cm0–2 cm2 cm
Jib luff tensionWrinklesWrinklesWrinklesWrinklesNo wrinklesNo wrinklesTightTight
CentreboardForwardForwardForwardForwardUpright 2.5 cm+2.5–6 cm+6–10 cm+10–12 cm
OuthaulTight3.8 cm2 cm2.5 cm0.5 cm1.3 cmVery tightVery tight
  • The rake row mixes imperial and metric inconsistently: 22′ 6″ is printed as both 6908 mm and 6900 mm, and 22′ 8″ as 6900 mm. Use one unit.
  • The spreader diagram (A 160 / B 420) doesn't match any single crew-weight line.
  • The same sheet is also hosted by the UK Fireball Association: https://www.fireballsailing.org.uk/images/technicalcontent/2025%20P%26B.pdf

Hyde Sails — Fireball tuning information (Code 2H mainsail, Superspar M7) Undated

Written for
Hyde Code 2H mainsail; Code 2E and 3B jibs; Superspar M7
Tension gauge
Loos tension gauge with plastic lugs, on the jib luff
How it’s measured
Rake with the tape pulled hard up to the mast tip (not just the lock position) to the top of the transom.
Source
Hyde Sails, Undated

Base setup

Mast heel
As far forward in the channel as practical; tight in the gate; check it is centred
Spreader length
410 mm, mast wall to wire (light teams can go shorter)
Spreader deflection (M7)
160 mm, aiming for 25 mm prebend with no strut or chocks; 40 mm in very light winds (via strut or more sweep)
Rig tension
27 on the jib luff
Jib tack height
Code 2E 100 mm off the deck; 3B 70 mm

Mast rake (to top of transom)

Wind (kn)Rake
5–86900 mm
10–156890 mm
15–206850 mm
20–256820 mm
Windy!6810 mm

Trim by condition

Jib
Foot firm without a lateral crease; set fairleads with the leech telltale; pull the jib pistons down until it stalls, then ease.
Kicker
Only snug while fully powered (mainsheet holds the leech); start pulling it once you play the sheet in gusts, and harder when overpowered to bend the mast; balance with cunningham.
Spinnaker
Good purchase on the pole uphaul and a stopper on the downhaul; light air pole level with the stowed boom, raise it as the wind builds to open the head.
  • A DOCX copy with the same content is at https://www.fireball-international.com/media/72712/Fireball%20M7%20Tune.docx.
  • Hyde is identified by the logo and file name; the PDF's metadata shows it was made in January 2019.

Speed Sails (Sailboats) — Fireball Tuning Guide by Sailboats Speedsails Undated

Written for
Not stated (Sailboats/Speedsails guide); Proctor or Superspar M7 masts (Cumulus also mentioned); 2:1 jib halyard
Tension gauge
Not named; lb on the jib luff
How it’s measured
Rake from the masthead to the top of the transom on the centreline; with the tape at the masthead it should read 18′ 9″ to the gooseneck black band.
Source
Speed Sails (Sailboats), Undated

Base setup

Spreaders, Proctor
Length 425 mm, deflection 125 mm
Spreaders, Superspar M7
Length 420 mm, deflection 145 mm
Prebend
27 mm, set at 22′ 8″ rake and 400 lb on the jib luff

Mast rake (all at 400 lb)

ConditionsRake
Both in the boat – high trapezing22′ 8″
Consistently overpowered, flapping the main upwind22′ 6″ (Cumulus: turn spreaders out one full turn going from 22′ 8″ to 22′ 6″)
Consistently overpowered – racing abandoned22′ 4″

Strut

BeaufortStrut
Force 0–1Pull the mast forward to flatten the lower main
Force 1–2Slightly behind neutral to power up the lower main
Force 2–4Neutral
Force 4+Ease off gradually as you become overpowered

Jib bars

ConditionBar from centrelineBar height
(condition not labelled)250 mmUp: flat sail, open leech; top telltale just breaks first
Mainsheet on centreline250 mmPull down for power low; move to 260 mm as the main is eased
Fully overpoweredEase to 270 mmEase the pulleys back up to flatten the foot and open the leech

Centreboard (1″ marks from the vertical '0')

ConditionBoard
(condition not labelled)1″ forward of vertical
Not yet planingVertical; raise 2″ as you begin to plane
OverpoweredRaise 3–4″ in flat water, up to 6″ in big seas

Trim by condition

Jib cunningham
Just remove luff creases; more as the wind builds.
Cunningham
Only once overpowered; pull hard in heavy air; ease it first when the wind lulls.
Kicker
Just take the slack out until you have to ease the main; from then on use enough to keep the top telltale flying about 80% of the time; let it off at the windward mark.
Outhaul
Tight upwind; ease about 2″ on long broad reaches.
Spinnaker
Keep tack and clew level; drop the pole a few inches in very light air.
  • Two table rows have no condition label on the web page (probably the light-air rows).

UK Fireball Association (unattributed) — Fireball Tuning Guide (for Proctor Epsilon or Superspar Mk2) Older guide (UKFA 2008 technical downloads)

Written for
Not stated; Proctor Epsilon or Superspar Mk2 masts
Tension gauge
Not named; lb on the jib luff
How it’s measured
Jib tension on hard (350 lb), tape pulled tight to the masthead on the main halyard, read at the centre of the transom where it meets the rear deck.
Source
UK Fireball Association (unattributed), Older guide (UKFA 2008 technical downloads)

Base setup

Mast rake
22′ 5½″ (6845 mm)
Spreader length
1′ 5⅛″ (460 mm)
Spreader deflection
5½″ (140 mm), batten across the shrouds to the back of the mast, rig on hard and no deck-level control
Rig tension
350 lb in medium conditions; about 280–300 lb in very strong wind or light (non-trapezing) wind
Jib sheeting
About 10–11″ (252–280 mm) from the centreline; on an HSP boat down hard on the jib bar

Trim by condition

Strut
With the main up, pull on until the mast is straight; slightly more in medium wind, slightly less in light or heavy.
Depowering order
Set up for maximum power in medium wind with the top telltale just breaking; as wind builds, pull on cunningham before easing the sail; then release some rig tension.
  • Written for older mast sections; no author or sailmaker is named.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Fireball resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Fireball by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Fireball class rules before changing equipment, and ask your class measurer if a part is not original equipment.