One-design race shop · Dinghy

Thistle Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Thistle

  • 24 verified parts
  • 6 brands
  • Fit checked Nov 2026

Fit verified for Thistle

All Thistle equipment

24 parts

Can’t find a part for your Thistle? Request a Thistle part

Official Harken dealer

Thistle deck layout

LOA
17' 0"
Beam
6' 0"
Draft up/dn
6"/4’6"
Weight
515 lb
SA (main and jib)
191 sq. ft.
SA (spin)
220 sq. ft.

Mainsheet & Traveler

Mainsheet & Traveler — Harken layout for the Thistle
Drawing: Harken
  1. 2 29mm Cheek BlockHarken 350 $18.95
  2. 4 29mm BlockHarken 348 $17.95
  3. 5 29mm BlockHarken 348 $17.95
  4. 7 Micro Cam-Matic® CleatHarken 468 $36.95
  5. 9 Micro Cam-Matic® CleatHarken 468 $36.95
  6. 11 40mm Block — SwivelHarken 2636 $38.95
  7. 12 40mm Block — SwivelHarken 2636 $38.95
  8. 14 40mm Ratchet Block — SwivelHarken 2608 $72.95
  9. 15 Standard Low Profile Cam Base — SwivelHarken 205 $163.95
  10. 16 57mm Ratchet Block — SwivelHarken 2135 $86.95
  11. 17 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  12. 19 38mm Bullseye FairleadHarken 237 $6.95
  13. 20 40mm BlockHarken 2650 $31.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Thistle tuning guide

Thistle tuning is mostly done before stepping: three sets of diamonds set the mast's bend to match the mainsail, then forestay tension, butt position (J) and rake (about 27′) are set and left alone, while sheet, traveller, outhaul, cunningham and jib lead do the work on the water. Diamond and forestay numbers depend on both the sail design and the gauge: North quotes Loos Model A and Loos Pro side by side, and Quantum quotes an unnamed 'black gauge' whose numbers look like the Loos Pro scale, so convert before comparing.

North Sails — Thistle Tuning Guide Undated web page (current)

Written for
DSD, VS (Fisher) and Proctor Thistle sails
Tension gauge
Loos Model A, with a conversion chart to the newer Loos Pro gauge
How it’s measured
Rake: tape hooked on the main halyard, measured from the masthead to the back edge of the bottom of the tiller hole. Forestay tension measured on the forestay (1/8″ 1×19), not the sidestays. Diamond tension set before stepping (1/16″ wire).
Source
North Sails, Undated web page (current)

Base setup

Mast butt (minimum J)
4′9″ aluminium, 4′8½″ wood (forestay to mast front); mast sits evenly on the step
Prebend
About ½″ (about 1/8″ gap at the front casting); shim the front of the step if over 1″
Rake
26′11½″ to 27′½″ for Proctor and Fisher mains; boom check 26′2″ minimum with the halyard at the top. With a 3/32″ forestay, tension reads about 5 numbers lower.
Forestay tension
Proctor 30–35 Loos Model A (260–360 lb); Fisher 28–32 (240–300 lb)
Diamonds, Proctor (Model A → Pro)
Top 12–13 → 9–10; middle 15 → 11; bottom 15–16 → 11–12. About 18 top to bottom for crews over 490 lb, loosening to a minimum of 10 below 430 lb.
Diamonds, Fisher (Model A → Pro)
Top 4–8 → 2–4; middle 9–13 → 5–10; bottom 4–8 → 2–4. About 6–14–9 (bottom to top); top diamond 4 or less below 430 lb.
Wood / old gold masts
Wood slightly less than aluminium and never above 16; older gold aluminium masts about 4 numbers lower on all diamonds
Jib lead (lateral)
Fisher: sheet crosses the thwart 15–16″ from centreline. Proctor: 16–17″.
Spreaders
Guide assumes 9½″ spreaders (Fisher jib 10½″, Proctor 11–11½″ as printed)
Spinnaker pole ring
32–33″ above the mast butt

Loos conversion, forestay (1/8″ cable)

PoundsLoos Model ALoos Pro
2402821
2603022
2803123
3003224
3203325
3403426
3603527

Trim by condition

Mast bend check
In about 8 mph with crew on the rail, overbend wrinkles run from the lower diamond toward the clew; in 15–18 mph they reach near the aft edge of the windows. Beyond that, add a shim. A stiff mast when pushed forward between the pole eye and lower diamonds suggests a poor butt set-up.
Main halyard / cunningham
Hoist fully (lower ball in light air). Cunningham: light air little or none; marginal hiking, wrinkles in the lower half; heavy air, wrinkles in the lower third only.
Outhaul
Proctor: seam 4–5″ from the boom in 4–8 kt medium chop, 3″ in smooth water, 1″ fully hiked, to the stop when overpowered. Fisher: no more than 2″ gap, snug above 10–12 mph, open 4–5″ reaching.
Mainsheet
Top batten about 15° to windward of parallel to the boom in ideal pointing (as printed); light air ease until the boom end is nearly over the transom corner.
Traveller
2–3″ to windward normally, 6″ maximum with proper rake, never past centreline; Proctor nearly full leeward above 15 mph; slightly below centreline above 20 mph.
Jib
Lead on the clew trim line; 1″ more sheet extension aft in heavy air. Proctor: foot just touching the rail about 2′ aft of the bow, leech 1½–2″ off the spreader. Fisher: leech 1″ off the middle-diamond spreader in medium/flat water, 2–3″ in very light or heavy air, 3–4″ after tacks or waves. Halyard: slight horizontal wrinkles off each snap.
Spinnaker
5–6″ luff curl; long bowline so the head sits 4″ from the mast.
  • The page's numbers are for the Model A gauge; use the conversion table for the Pro gauge.
  • The '15° to windward' mainsheet figure and the spreader/jib-lead sentence are reproduced as printed; check them against the quick guides.

North Sails — Thistle DSD Designs Quick Tuning Chart 2021 (PDF dated July 2021)

Written for
North DSD main and jib
Tension gauge
Loos Pro
How it’s measured
Centre the mast by taking a tape to the rail at the shroud on each side.
Source
North Sails, 2021 (PDF dated July 2021)

Base setup

Forestay tension
23–25 Loos Pro (240–300 lb) in all conditions
Mast butt
4′9″
Mast rake
26′10.5″ – 27′
Diamonds (Loos Pro)
Top 3–4, middle 11–12, bottom 9–10
Jib lead laterally
Sheet crosses the thwart 15½″ from centreline
Prebend
1.5″

On-the-water tuning (wind units not stated)

ControlLight (0–6)Medium (6–12)Heavy (12+)
MainsheetEased; upper batten open if possibleUpper batten parallel to boom unless acceleratingEased; upper batten twisted open past parallel
VangCompletely offOnly in upper ranges, very tightVery tight (boom shows bend)
OuthaulShelf open 2″Shelf open 1″Shelf closed, outhaul tight
CunninghamNoneSnug, wrinkles in lower ½ of luffTighter, wrinkles in bottom 1/4
TravellerTo windward 5″ if not tacking muchCentredCentred until upper ranges, then 8–10″ to leeward
Mast bendOverbend wrinkles just evidentOverbend wrinkles presentOverbend wrinkles very deep
Jib halyardVisible wrinkles (no sag between snaps)Slight wrinklesNearly smooth luff
Jib lead fore & aftOn trim lineOn trim line1½″ aft of trim line
Jib sheet (off spreader)2–3″1-1/2″2–3″ (assuming 9½″ spreaders)
Jib telltales (steering)Both straight backWindward showing stall, leeward straight backWindward stalled; luff breaking 8–10″ back in bigger puffs

Trim by condition

Main halyard
Upper ball with all new mains in all conditions; with older mains (pre-slug at tack) lower the halyard below 10 mph to develop wrinkles.

Quantum Sails — Thistle Quick Tuning Guide June 2020

Written for
Quantum Thistle sails (models not named)
Tension gauge
"All tensions on the black gauge" (model not named; see notes)
How it’s measured
Not described on the chart.
Source
Quantum Sails, June 2020

Base setup

Mast step
Maximum forward
Shims
No shims under the mast

Quick tuning by true wind (knots); rig tension on the black gauge

TWS (kn)RakeRig tensionDiamonds (bottom to top)Jib outboardCentreboardMainsheet (top batten)Traveller
0–627′22Not given in this row (column header: bottom to top)16″4.5″ backParallelUp to 2″
7–9 flat water27′ 1/8″247-11-3.516″2″ backSlightly closedCentre
7–9 waves27′ 1/4″27Same (ditto)16.5″4.5″ backParallelCentre
10–1527′ 1/4″27Same (ditto)16.75″BackEased in puffsDown 2–5″
16+27′ 1/4″27Same (ditto)16″BackEased in puffsDown 5–12″
  • The diamond column shows 7-11-3.5 on the 7–9 flat-water row with ditto marks below; the 0–6 row carries only the 'Bottom To Top' label, so its diamond setting isn't stated separately.
  • Centreboard reads only 'Back' at 10 kn and above, with no amount.
  • 'Black gauge' is not identified on the chart, and it doesn't say whether rig tension is read on the forestay. For comparison only: North's Lightning guide calls the black spring-loaded Loos gauge the PT-1, and Quantum's 22–27 rig-tension readings fall inside North's Loos Pro forestay scale for Thistles (21–27 = 240–360 lb), not its Model A scale (28–35). That suggests a Loos Pro/PT-type gauge, but it is an inference; don't convert Quantum's numbers to pounds without checking with Quantum.

North Sails — Fisher Thistle – Quick Tuning Guide 2007 (PDF dated January 2007)

Written for
North Fisher (VS) main and jib
Tension gauge
Loos Model A and Loos Pro
How it’s measured
Centre the mast with a tape to the rail at each shroud.
Source
North Sails, 2007 (PDF dated January 2007)

Base setup

Forestay tension
28–32 Loos Model A / 21–25 Loos Pro (240–300 lb) in all conditions
Mast butt
4′9″
Mast rake
26′11½″–27′½″
Diamonds
4–8 top, 9–13 middle, 4–8 bottom (Model A); 2–4, 5–10, 2–4 (Pro); lower numbers for lighter crews
Jib lead laterally
Sheet crosses the thwart 15½″ from centreline
Mast flexibility
Shim for slight prebend and a bit of wiggle when pressed forward

On-the-water tuning (wind units not stated)

ControlLight (0–6)Medium (6–12)Heavy (12+)
MainsheetEased; upper batten open if possibleUpper batten parallel to boom unless acceleratingEased; upper batten twisted open past parallel
VangCompletely offOnly in upper ranges, very tightVery tight (boom shows bend)
OuthaulShelf open 2″Shelf open 1″Shelf closed, outhaul tight
CunninghamNoneSnug, wrinkles in lower ½ of luffTighter, wrinkles in bottom 1/4
TravellerTo windward 5″ if not tacking muchCentredCentred until upper ranges, then 8–10″ to leeward
Mast bendOverbend wrinkles just evidentOverbend wrinkles presentOverbend wrinkles very deep
Jib halyardVisible wrinkles (no sag between snaps)Slight wrinklesNearly smooth luff
Jib lead fore & aftOn trim lineOn trim line1½″ aft of trim line
Jib sheet (off spreader)2–3″1-1/2″2–3″ (assuming 9½″ spreaders)
Jib telltalesBoth straight backWindward showing stall, leeward straight backWindward stalled; luff breaking 8–10″ back in bigger puffs

Trim by condition

Main halyard
Upper ball with all new mains; with older (pre-slug) mains lower the halyard below 10 mph to develop wrinkles.
  • Older North edition; the 2021 DSD chart uses a different rake (26′10.5″–27′) and diamond numbers.

North Sails — Proctor Thistle – Quick Tuning Guide 2007 (PDF dated January 2007)

Written for
North Proctor main and jib
Tension gauge
Loos Model A and Loos Pro
How it’s measured
Centre the mast with a tape to the rail at each shroud.
Source
North Sails, 2007 (PDF dated January 2007)

Base setup

Forestay tension
30–35 Loos Model A / 22–27 Loos Pro (260–360 lb) in all conditions
Mast butt
4′9″
Mast rake
26′11½″–27′½″
Diamonds
12–13 top, 15 middle, 15–16 bottom (Model A); 9–10, 11, 11–12 (Pro); lower numbers for lighter crews
Jib lead laterally
Sheet crosses the thwart 16½″ from centreline
Mast flexibility
Shim for slight prebend and a bit of wiggle when pressed forward

On-the-water tuning (wind units not stated)

ControlLight (0–6)Medium (6–12)Heavy (12+)
MainsheetEased; upper batten open if possibleUpper batten parallel to boom unless acceleratingEased; upper batten twisted open past parallel
VangCompletely offSnug only in upper rangesTight only in upper ranges
OuthaulShelf open 4–5″Shelf open 3″Shelf closed, outhaul tight
CunninghamNoneSnug, wrinkles in lower 5/8 of luffTighter, wrinkles in bottom 3/8
TravellerTo windward 5″ if not tacking muchTo leeward to balance helmWell to leeward to balance helm
Mast bendOverbend wrinkles just evidentOverbend wrinkles presentOverbend wrinkles very deep
Jib halyardVery visible wrinkles (no sag between snaps)Visible wrinklesSlight wrinkles
Jib lead fore & aftOn trim lineOn trim line1″ aft of trim line
Jib sheet (off spreader)2″1–2″2–3″ (assuming 9½″ spreaders)
Jib telltalesBoth straight backWindward showing stallWindward stalled; luff breaking 8–10″ back in bigger puffs

Trim by condition

Main halyard
Upper ball in all conditions.
  • The current web guide gives the Proctor lateral jib lead as 16–17″; this chart says 16½″.

North Sails — Northwest Thistle – Quick Tuning Guide 2007 (PDF dated January 2007)

Written for
North Northwest-design main and jib
Tension gauge
Loos Model A and Loos Pro
How it’s measured
Centre the mast with a tape to the rail at each shroud.
Source
North Sails, 2007 (PDF dated January 2007)

Base setup

Forestay tension
21–32 Loos Model A / 19–24 Loos Pro (240–300 lb) in all conditions
Mast butt
4′9″
Mast rake
27′
Diamonds
6–10 top, 10–14 middle, 10–14 bottom (Model A); 3–6, 6–11, 6–11 (Pro); lower numbers for lighter crews
Jib lead laterally
Sheet crosses the thwart 17½″ from centreline
Jib lead fore and aft
108″ in all conditions

On-the-water tuning (wind units not stated)

ControlLight (0–6)Medium (6–12)Heavy (12+)
MainsheetEased; upper batten open if possibleUpper batten parallel to boom unless acceleratingEased; upper batten twisted open past parallel
VangCompletely offSnug only in upper rangesTight (boom shows some bend)
OuthaulShelf open 2½–3½″Shelf open 2–3″Shelf closed, outhaul tight
CunninghamNoneWrinkles only in lower ½ of luffTighter, wrinkles in bottom 1/3
TravellerTo windward 4″ if not tacking muchCentred to leeward to balanceTo leeward 8–15″ to keep balance
Mast bendOverbend wrinkles just evidentOverbend wrinkles presentOverbend wrinkles very deep
Jib halyardSlight wrinklesSlight wrinklesSlight wrinkles
Jib lead laterally17½″17½″18½–19½″ out from centre
Jib sheet (off spreader)1 1/2–2 1/2″1-1/2″2–3″ (assuming 9½″ spreaders)
Jib telltalesBoth straight backBoth straight backWindward stalled; luff breaking 4–5″ back in bigger puffs

Trim by condition

Main halyard
Upper ball in all conditions.
  • The Model A forestay range (21–32) is much wider than the Pro range (19–24) for the same 240–300 lb; reproduced as printed.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Thistle resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Thistle by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Thistle class rules before changing equipment, and ask your class measurer if a part is not original equipment.