One-design race shop · Dinghy
Megabyte Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Megabyte
All Megabyte equipment
1 part
No Megabyte parts match these filters.
Can’t find a part for your Megabyte? Request a Megabyte part
Go fast
Megabyte tuning guide
The Megabyte's unstayed rig is tuned with cunningham, outhaul, vang, mainsheet and traveller rather than rake or rig tension. The only published notes we found are written for the Mark I rig; the Mark II has a more flexible carbon upper mast, so the cunningham matters even more there.
US Sailing (Megabyte sailor's notes, author not named) — MEGABYTE Mark I Rig — tips and techniques 2020 (DOCX dated March 2020)
- Written for
- Megabyte Mark I mainsail (some remarks on the Mark II rig)
- Tension gauge
- Not applicable
- How it’s measured
- Outhaul as the gap between the foot and the centre of the boom at the widest point (inches); mainsheet aimed so the boom points at the aft leeward corner of the transom.
- Source
- US Sailing (Megabyte sailor's notes, author not named), 2020 (DOCX dated March 2020)
Base setup
- Outhaul starting point
- About 6–7″ between foot and boom at the widest point; leave it unless the wind changes
- Top batten
- Very little tension on the upper full-length batten so the head inverts when tacking, especially in light air
- Hiking straps
- Adjust for straight-leg hiking
Typical settings (change with body weight and chop)
| Control | Light (up to 10 kn) | Medium (10–18 kn) | Heavy (18–30 kn) |
|---|---|---|---|
| Cunningham | Snug, slight wrinkles from mast joint to clew | Enough to smooth the wrinkles between clew and mast joint; slightly less in chop if not overpowered | Grommet pulled all the way to the boom |
| Outhaul | Loose: about one hand (about 6″) from the centre of the boom | Slightly less than a hand: 4–5″ | Maxed out if overpowered; otherwise 2–3″ at maximum draft |
| Vang | Snug for the mainsheet tension, set after cunningham, outhaul and sheet/traveller | If overpowered, enough that the boom doesn't rise when the sheet is eased; otherwise snug to taut | Hard enough that when the sheet is eased the blocks part at 45° or less from the cockpit deck; the boom must not lift |
| Mainsheet / traveller | Traveller to windward, loose leech, top batten parallel to the boom | Start with the traveller at the leeward end, sheet for leech tension and mast bend, then bring the traveller up so the boom points at the leeward transom corner | After sheeting the boom to the leeward corner, move the traveller to windward so the head can twist and spill pressure |
| Body upwind | Slightly forward of the mainsheet block | At the widest point, at or slightly behind the traveller, hiking | Adjacent to the traveller, maximum hike |
| Body reaching | As upwind, slightly aft | Body angled back about 45°, move aft as it planes | Aft, near the end of the tiller, angled aft |
| Body downwind | As far forward as possible with feet in the cockpit; heel as needed | Straddle the centreboard until planing, then move aft | Aft enough to lift the stern slightly (calmest wake); move fore and aft for waves |
Trim by condition
- General
- Sail flat and don't over-trim or pinch; in chop bear away a few degrees for speed. Aim the boom at the aft leeward corner.
- Gusts
- Mainsheet is the first depowering control: ease 6–12″, hike, and trim back as the gust fades; ease slightly and bear away in lulls.
- Cunningham
- The first control line to reach for after the mainsheet; play it in puffs. Too much pulls the draft forward and depowers, so try leaving a few luff wrinkles.
- Draft position
- Light air: balanced 50:50 at the first batten below the top batten. Medium: tends to slip aft (55:45), so add cunningham. Heavy: vang flattens the sail but pushes draft aft; use cunningham to bring it forward of the middle.
- Big sailor, light air
- Slightly looser cunningham, outhaul looser for longer (not much beyond a hand), vang only snug until hiking, sit forward with knees at the block, looser sheet and bow down.
- Small sailor, heavy air
- Cunningham maxed, outhaul nearly maxed, vang as hard as possible (ease slightly for tacks); set leech tension with the traveller down, then work the sheet in and out 1–2 ft continuously. Trimming block-to-block can make you very slow.
- Twin traveller cars and bridle
- Tie the traveller line ends together for control from windward. Releasing the leeward traveller line before a tack in breeze lets the car slide to leeward for the new tack; a bridle steepens the sheeting angle and gives one more shape variable (applies to Mark I and Mark II).
- The document reads like an edited draft (some duplicated and half-deleted wording), so a few points are ambiguous.
- The author isn't named in the text; the file is hosted by US Sailing.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Megabyte resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Megabyte by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Megabyte. Racing legality depends on your class or handicap rules; check them before changing equipment.