One-design race shop · Dinghy
RS500 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS500
All RS500 equipment
22 parts
Fit verified for RS500
Rooster
Rooster Pro Plus Padded Toestrap Set for RS500 Helm
Part # ROO142510
$54.90
$61.00Fit verified for RS500
Selden
Selden Pop-rivet, ø4,8 X 9,9 mm, Monel, Dome Head
Part # sel-167-007-10
$45.00
Fit verified for RS500
Selden
Selden 20 mm Ball Bearing Block - Single
Part # sel-402-101-01r
$16.15
$19.00Fit verified for RS500
Selden
Selden Pop-rivet, ø4,8 X 12,7 mm, Monel, Countersunk
Part # sel-167-022-05
$36.00
Fit verified for RS500
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for RS500
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for RS500
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for RS500
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for RS500
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for RS500
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for RS500
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for RS500
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for RS500
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for RS500
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for RS500
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for RS500
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No RS500 parts match these filters.
Can’t find a part for your RS500? Request a RS500 part
Go fast
RS500 tuning guide
The RS500 is a one-design asymmetric trapeze boat with a simple rig: rake is set with the shroud pins and forestay purchase, rig tension on the forestay, and the jib sheeting angle by the length of the jib tack line. The only published guides are owner/class notes from 2007–2009, with tension quoted on a Superspars gauge or in lb.
Tim Wilkins (RS500 Class Association) — Tim's RS500 Setup Guide 6 November 2009
- Written for
- Class one-design sails
- Tension gauge
- Not named; tension in lb, read on a shroud at about shoulder height
- How it’s measured
- Rake: hoist a long tape to the masthead on the main halyard and measure to the top of the transom. Don't copy another boat's pin holes, as shroud lengths vary.
- Source
- Tim Wilkins (RS500 Class Association), 6 November 2009
Base setup
- Mast foot
- Factory middle position; no need to move it
- Rake range
- 6350 mm (20′10″) to 6430 mm (21′1.5″); the author uses 6430 mm (good in light/medium, a handful in breeze)
- Rig tension
- About 300–400 lb, set on the forestay purchase; enough that forestay and leeward shroud don't sag
- Lowers
- Just no slack with rig tension on and the main down; looser only if very windy
- Spreaders
- Factory setting from the boat's instructions (no figure given)
- Jib tack line
- About 2 cm (short) to about 8 cm (long)
Trim by condition
- Rake
- Rake forward for power and pointing in light to medium wind, back in heavier wind to depower and plane upwind. Changing rig tension also changes rake.
- Jib tack line
- Short (about 2 cm) lowers the jib, flattens the foot and opens the slot: for breeze and chop. Long (up to about 8 cm) raises it and closes the slot: for light wind and flat water, with more risk of oversheeting.
- Jib sheet
- About an inch off bar tight upwind; ease a few inches if the boat stalls.
- Jib halyard
- Only enough to remove horizontal creases; extra tension flattens the jib but hurts pointing.
- Kicker (gnav)
- Main control: leech telltales stalling about half the time upwind; more and more as it gets windy; very little downwind.
- Downhaul
- Depower only; leave luff creases in until overpowered, then pull on progressively; release downwind.
- Outhaul
- Pull fully on, then ease until creases along the boom disappear; leave it for the run (it self-eases as the boom goes out).
- Lowers
- Slack lowers flatten the main but in lighter wind let the mast over-bend (crease from tack to batten) and stop the kicker closing the leech.
- Mainsheet strop
- Set so the boom can come to centreline block-to-block without pulling it down more than a few inches; re-check after big rake changes.
- An owner's setup guide rather than a sailmaker guide; the author says there's no guarantee his settings are optimal.
- Forestay purchase rope can stretch during a day's sailing, lowering tension.
RS500 Class Association (owners' notes) — RS 500 Rig Tuning Notes September 2007
- Written for
- Class sails
- Tension gauge
- Superspars gauge (readings with lb equivalents)
- How it’s measured
- Rake from the masthead (tape on the halyard) to the top of the transom. Rig tension measured at shoulder height on a shroud when standing next to the boat.
- Source
- RS500 Class Association (owners' notes), September 2007
Base setup
- Spreaders
- Length and deflection as per the RS manual for every boat listed
Settings from early boats (Superspars gauge)
| Boat | Mast foot | Shrouds | Lowers | Rake | Rig tension | Notes |
|---|---|---|---|---|---|---|
| 521 (first outing) | 1 hole visible at the front | 4 holes down | 2 holes up | 630 cm (20′8½″) | 285, units not stated (25 on Superspars) | Light (<F3); too much weather helm, rig floppy |
| 521 (revised) | 1 hole visible at the front | 4 holes down | 2 holes up | 637 cm (20′11″) | 400 lb (30 on Superspars) | Cascade shortened for more tension; to be tried |
| 519 | 1 hole visible at the front | 3 holes down | 3 holes up | 640 cm | 370 lb (29 on Superspars) | Boat feels balanced |
| 510 | 1 hole visible at the front | 3 holes down | 3 holes up | 648 cm (21′3½″) | 285, units not stated (25 on Superspars) | Boat feels balanced |
| 523 (first) | 1 hole visible | 4 holes down | 2 holes up | 21′2½″ | 30 on Superspars | Weather helm in all conditions tested so far; rig breaker then shortened for more tension and the gnav cascade for a tighter leech |
| 523 (revised) | 0 holes visible | 4 holes down | 2 holes up | 21′2½″ | 30 on Superspars | Helm almost neutral in F1–2 on the sea |
- A log of early owners' trial settings (boats 521, 519, 510, 523 from Wembley, Whitefriars and Hickling Broad clubs), not a recommendation. The header date shows a tracked edit between 2006 and 2007; the PDF was created in September 2007. The 523 rows are tracked-change insertions.
- Where only a Superspars reading is given, no lb equivalent is stated; the '285' readings have no unit in the source.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the RS500
Technical
RS500 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS500 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS500 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRS Class Association Rules All Classes v4 June 2022; RS500 Class Rules (undated)
- Class associationrs500.org
- Builder specificationsRS500 on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS500 part