One-design race shop · Keelboat
Star Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Star
All Star equipment
28 parts
Fit verified for Star
Harken
Harken Swivel Cam Cleat - Base (Standard) w/ Cam-Matic 412 - Line: 8/16 to 3/8 in (8 to 10 mm)
Part # HAR403
$239.95
$272.20Fit verified for Star
Harken
Harken Block - Micro 22mm Single - Fiddle - V-Jam / Becket
Part # HAR245
$47.95
$54.20Fit verified for Star
Harken
Harken Block - Carbo Ratchamatic 57mm Double - Standard Grip (Black)
Part # HAR2634
$325.95
$370.15Fit verified for Star
Harken
Harken Traveler Car 1/2 in (13.0 mm) Micro - Loop
Part # HAR2703
$132.95
$150.50Fit verified for Star
Harken
Harken Cam Cleat - Cam-Matic 150 w/ X-treme Angle Fairlead 375 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR459
$66.95
$75.90Fit verified for Star
Nautalytics
Nautalytics Mast Mount Compass (Digital Compass)
Part # NTL-MASTMOUNT
$500.00
Fit verified for Star
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 100' long
Part # buc-cro-nal38100
$41.18
Fit verified for Star
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 150' long
Part # buc-cro-nal12150
$122.00
$123.70Fit verified for Star
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 200' long
Part # buc-cro-nal12200
$161.00
$169.04Fit verified for Star
Lewmar
Lewmar Rode - 150' 1/2"8Plt Splcd 5/16" Skl
Part # LEWHM150PX
$329.00
$498.95Fit verified for Star
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 150' long
Part # buc-cro-nal38150
$70.70
Fit verified for Star
Harken
Harken Block - Carbo Ratchamatic 57mm Single - Swivel / Standard Grip (Black)
Part # HAR2625
$121.95
$138.30Fit verified for Star
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Star
Harken
Harken Block - Carbo 29mm Double - Swivel / Becket
Part # HAR343
$57.95
$66.10Fit verified for Star
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for Star
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
No Star parts match these filters.
Can’t find a part for your Star? Request a Star part
Official Harken dealer
Star deck layout
- LOA
- 6.9 m - 22.7 ft
- Beam
- 1.7 m (5.7 ft)
- Draft
- 1.0 m (3.3 ft)
- Weight
- 671 kg (1479 lb)
- Sail Area
- 26.5 sq m (285 sq ft)
Double Ratchamatic® Mainsheet
-
1
57mm T2™ Loop Soft-Attach BlockHarken 2151
$60.95 -
2
57mm T2™ Loop Soft-Attach BlockHarken 2151
$60.95 -
3
57mm T2™ Loop Soft-Attach BlockHarken 2151
$60.95 -
4
Double Cam Base — SwivelHarken 403
$239.95 -
5
22mm Fiddle Block — V-Jam, BecketHarken 245
$47.95 -
6
22mm Fiddle Block — V-Jam, BecketHarken 245
$47.95 -
7
25mm Wire Block — ShackleHarken 300
$47.95 -
9
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
10
29mm Double Block — Swivel, BecketHarken 343
$57.95 -
11
29mm Double Block — SwivelHarken 342
$53.95 -
12
Standard Cam-Matic® Kit — X-Treme Angle FairleadHarken 459
$66.95 -
13
40mm Double BlockHarken 2642
$72.95 -
14
57mm Double Ratchamatic® Block — SwivelHarken 2634
$325.95 -
15
57mm Ratchamatic® Block — SwivelHarken 2625
$121.95 -
16
57mm Double Ratchamatic® Block — SwivelHarken 2634
$325.95
Carbo T2™ Jib Cars
-
2
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
3
13mm Loop CarHarken 2703
$132.95 -
6
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
7
13mm Loop CarHarken 2703
$132.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Star tuning guide
A Star is set up mostly with the mast out of the boat (intermediate length, spreader sweep) and then with mast-butt position, rake, upper-shroud tension and lower-shroud spacing, with the upper and lower runners (backstays) doing most of the work on the water. Read each guide with its own gauge and rake method: North and Quantum quote the Loos PT-1, Fritz the PT-2, Quantum 2003 also gives old silver-Loos figures, and rake is measured to a forestay mark by some guides and to the forestay pin by others, so the numbers don't transfer between guides.
Quantum Sails — Star Tuning Guide 2020
- Written for
- Quantum Star main and jib (no model names)
- Tension gauge
- Loos PT-1 (the quick-setup table calls it the "Pro Loos Gauge")
- How it’s measured
- Intermediates: with the mast on two trestles (at the base and just above the intermediate attachment), pull the uppers and then the intermediates down the front of the mast and mark each; or use a spring scale at 18 lb. Spreader sweep: back of the mast to a shock cord tied between the tips level with the shroud bolts. Rake: from where the forestay goes through the deck up to a mark made, rig down, at the top of the black band. Mast butt: checked from the back of the mast just above the butt casting to the plane of the transom (a heavy batten held upright against the transom helps); the older-Folli figure is quoted from the transom-deck intersection to the centre of the aft mast-step bolt. Shroud tension is read with both backstays at 5 on the PT-1 in the upwind position and the ram completely off.
- Source
- Quantum Sails, 2020
Base setup
- Intermediates
- 2 15/16″ (7.4 cm in the text, 7.5 cm in the quick-setup table) above the upper-shroud mark; range 2⅞–3″ (7.3–7.6 cm)
- Spreader sweep
- 5″ (12.7 cm) for medium to heavy air; up to 5¾″ (14.7 cm) for more bend in light air (then needs more lower backstay as it builds)
- Mast butt
- 14′ 9″–14′ 11″ (450–455 cm). Older Follis: 14′ 9¼″ (450 cm) from the transom-deck intersection to the centre of the aft mast-step bolt. Newer Follis, Lillia, P-Star and Mader: further forward, up to 14′ 11″ (455 cm). New boats: start with the builder's figure.
- Rake
- Quick-setup table: 36.5–37″ (92.7–94 cm), longer for newer boats. Text: 36″ (94 cm) on a longer forestay. Adjust with the under-deck stay master or the purchase behind the barney post.
- Backstays (for setting shrouds)
- 5 on the PT-1 each, upwind position
- Uppers
- Quick-setup table: 23–24 on the Pro Loos gauge. Text: 24 on the PT-1 for 8–12 kn (23 in lighter air, 25 in stronger).
- Lowers
- Mark the mast 36″ (91.5 cm) above the top of the gooseneck band; shroud to shroud at that mark 29″ (73.5 cm). Quick alternative: hand-tight, then back off 1.5 turns. Tighter lowers take power out, looser add it.
- Shroud position
- Lowers in line with the front of the mast; uppers attached at equal positions each side
- Backstay length (new mast)
- Top of the black band to the backstay bearing point 6–7½″
- Jib spreader mark
- 18″ (458 mm) from the side of the mast, both spreaders
- Jib tack height
- About 1″ (25 mm) off the deck
- Jib lead
- About 86½″ (2200 mm) from the headstay; sheet angle 45–50° off the deck (up to 75° in light air); athwartships 14″ (356 mm) from centreline
Upper shroud tension by wind (Loos PT-1)
| Wind | Uppers PT-1 |
|---|---|
| Lighter breeze | 23 |
| 8–12 kn (medium) | 24 |
| Stronger breeze | 25 |
Runner (backstay) use by wind, from the guide's runner tips
| Wind | Lower runner | Upper runner | Other |
|---|---|---|---|
| Under 6 kn, crew on deck | Just a touch | Off | Top batten hooks easily from boom weight |
| 6–8 kn, crew starting to hike | About 3″ on | — | Top batten parallel to the boom or 5° open |
| Crew fully hiked | Ease a little | Add slowly to keep the forestay tight in chop | Firm mainsheet, more twist; diagonal wrinkles across the window = fast-forward mode |
| 18+ kn | Firm | Hard | Cunningham firm; rake may be eased for twist |
Outhaul by wind
| Condition | Outhaul |
|---|---|
| 0–4 kn upwind | Snug to the boom |
| 6–8 kn upwind | Eased up to 1½″ |
| Over 10 kn upwind | Tightened to flatten |
| Downwind | Eased so the shelf foot opens (range up to about 8″ off the boom) |
Trim by condition
- Mainsheet
- The key control; adjust it for every change in wind, water, mode or manoeuvre.
- Cunningham
- Leave horizontal wrinkles below 8 kn; use it to balance the boat as it builds and ease it if the boat feels slow; fully off downwind.
- Lower backstay
- Off or just snug below 6 kn; loose or about 1″ from slack above 6 kn; pull more when the crew is just over the side for power; ease when windy to go forward, tighten as needed to hold height and keep the main quiet.
- Upper backstay
- For overpowered conditions: flattens the upper main and tightens the forestay. Tighter = lower and faster in heavy air; looser = higher and slower. The lower goes on first.
- Reaching / running
- Reaching: ease the backstays to bring the mast upright. Running: ease both so the mast goes forward; in heavy air don't let it go more than 15–20″ forward.
- Vang downwind
- Very little; keep the aft end of the top batten parallel to the boom or looser.
- Mast forward lever
- Reaching: only enough to stop the mast reversing. Running: pull until the mast is straight or slightly inverted, with the windward spreader standing straight out.
- Sliding mast butt
- Move the aft pin back in light air and forward one or two holes in breeze, so the butt always bears on both the partner and the aft step bolt.
- Jib
- Leech on the spreader mark about 95% of the time upwind; play the sheet nearly as much as the main and match the main and jib leech shapes. Lead: some fullness in the foot with the middle batten straight back; forward if the foot flutters. Move outboard only when overstanding or in puffy winds over 22 kn.
- Jib halyard and tack
- Low enough that the leech goes well inside the mark with the sheet two-blocked. Downwind raise the jib so the head is 12–18″ below the halyard sheave; lower it before the leeward mark. Tack downhaul just enough to remove wrinkles.
- Backstay and jib
- Both backstays reduce headstay sag and flatten the jib; backstay and jib halyard go on and off together.
- The same guide is hosted by the Austrian Star fleet at https://www.starclass.at/images/tuning-guides/Quantum-Star_TuningGuide_2020.pdf.
- Inside the guide the intermediate setting is given as 7.4 cm in the text and 7.5 cm in the table, and rake as 36.5–37″ in the table but 36″ (94 cm) in the text (36″ is about 91.5 cm).
Fritz Sails (Fritz Segel) — Star Quick Go Fast Advices Revised June 06 2020
- Written for
- Fritz Star main and jib (no model names)
- Tension gauge
- Loos PT-2 (the guide warns gauges differ and suggests averaging several)
- How it’s measured
- Intermediates and forestay mark set with a hand scale at 100 N (10 kg). Spreader sweep: back of the mast (not inside the groove) to a cord between the tips, spreaders max aft. Rake: from where the headstay exits the deck to the mark made, rig down, where the forestay meets the top of the black band. Shrouds read with 10 PT-2 units on each upper backstay, check stay and puller slack, spreaders locked aft; uppers measured 1500 mm above the sheerline.
- Source
- Fritz Sails (Fritz Segel), Revised June 06 2020
Base setup
- Intermediates
- Difference uppers to intermediates 73–75 mm; start at 74 mm. 73 mm for heavy air or lighter crews, 75 mm for heavy teams.
- Spreader sweep
- 127–135 mm; 135 mm for lighter crews, 127 mm for more power
- Mast foot
- 4520–4550 mm from the stern to the back of the mast groove at its lower end (check the builder's figure)
- Shroud position
- Uppers in line with the front of the mast; lowers just behind the uppers
- Rake marks
- Mark 93, 94, 95 and 96 cm on the rake line in the cockpit; set the shrouds at a base rake of 93 cm
- Uppers base
- 23 on the PT-2
- Lowers base
- Mark 91.5 cm above the top of the black band, put an elastic round the lowers there and measure across: 70 cm; check symmetry, then fine-tune for a straight mast under sail
- Jib car (upwind)
- 220 cm from the headstay-deck intersection to the centre of the block; 35.5 cm from centreline
Settings by wind (uppers on Loos PT-2)
| Wind | Uppers PT-2 | Lowers (spacing at the 91.5 cm mark) | Rake | Outhaul |
|---|---|---|---|---|
| 0–5 kn | 22 | 70 | 95 | 4–3 cm open |
| 6–10 kn | 23 | 70 | 93–94 | 3–2 cm open |
| 11–15 kn | 24–25 | 72 | 94–95 | Max out |
| 16–20 kn | 25–26 | 73–74 | 95 | Max out |
| 20+ kn | 26 | 73–74 | 95–96 | Max out |
Trim by condition
- Lowers
- After the dock setting, ease the runners and push the mast forward until the lowers load, sight up the mast and adjust for straightness; finish the job sailing upwind.
- Sail care
- Roll main and jib; if they had to be folded for travel, rinse and let them dry under tension before sailing.
- The table's lowers and rake columns have no units; they match the shroud-to-shroud spacing and the 93–96 cm rake marks (both cm) used in the setup section.
- Fritz puts the uppers in line with the front of the mast and the lowers behind them — the opposite of the North and Quantum guides.
- Hosted by the Austrian Star fleet (starclass.at); a German-language Fritz general trim booklet is linked from the same page but isn't Star-specific.
North Sails — Star Tuning Guide Undated (current web page)
- Written for
- North Star main and jib (yarn-tempered Dacron); no model names
- Tension gauge
- Loos Pro Model gauge (PT-1)
- How it’s measured
- Intermediates: mark the uppers' and intermediates' bearing points on the mast and measure the difference. Spreader sweep: back of the mast to a taut shock cord tied just below the spreaders. Rake: to a mark on the headstay level with the top of the lower black band at the gooseneck. Butt: back of the mast along the deck to the transom. Uppers read with upper backstays at 10, forward bender off and spreaders locked aft.
- Source
- North Sails, Undated (current web page)
Base setup
- Intermediates
- 73 mm (2⅞″) to 76 mm (3″); tighter for heavy air or light crews, longer for light-air power
- Spreader sweep
- 127–140 mm (5–5½″); less sweep stiffens the middle of the mast, more lets it bend (flatter main, more lower checkstay needed). Square the spreaders to the butt by sighting a batten on the butt casting; seize the Allen screws with Loctite. A soft mast may need less sweep, a stiff one more.
- Mast butt
- Between 14′ 10″ (4520 cm) and 14′ 9″ (4495 cm), as published; older boats (keel further aft) want the butt further aft. Strong effect on upwind balance.
- Shroud cars
- Lowers in line with the front of the mast; uppers about 1.3 cm (½″) forward of the lowers (spreaders back, backstays on)
- Upper backstays
- 10 on the Loos gauge
- Rake
- 93–96 cm (36½–37¾″) for most boats
- Uppers
- 22–23.5 on the Loos gauge
- Lowers
- Mark 91.5 cm (36″) above the top of the black band; with the shrouds pulled together, 70–74 cm (27½–29″) apart
- Jib lead
- Start at 7′ 2″ (215 cm) from the headstay to the centre of the car; about 1.3 cm forward in rough water, about 1.5 cm back as the wind builds. Athwartships 14″ (36.5 cm) from centreline; out 2.5 cm (1″) only in the windiest conditions.
- Jib tack / spreader mark
- Tack about 2.5 cm (1″) off the deck; trim to the 45.7 cm (18″) spreader mark, never inside it
Settings by wind (uppers on Loos PT-1; wind units not stated, presumably knots)
| Control | Light 0–6 | Medium 6–12 | Heavy 12+ |
|---|---|---|---|
| Mast rake (newer boats) | 95.5 cm | 94.5 cm | 97 cm |
| Upper shroud tension | 21 | 23.5 | 26 |
| Outhaul | ¾″ (2 cm) | ½″ (1.25 cm) | Maximum out |
| Cunningham | None | Snug | Increase to bleed power |
| Jib cloth tension | Enough to remove wrinkles at all times | Same | Same |
| Jib car fore & aft | 7′ ½″ (217 cm) | 7′ 2″ (218.5 cm) | 7′ 2½″ (220 cm) |
| Jib car athwartships | 14″ (35.5 cm) | 14″ (35.5 cm) | 14½–15″ (printed "38-7.0 to 38.5 cm") |
| Upper backstay | Slack | Snug | Hard |
| Lower backstay | Slack | Tight for maximum power | Ease as needed to bleed power |
Trim by condition
- Mainsheet
- The most sensitive control: harder = tighter leech, more power, helm and pointing; eased = more twist, less helm. Hard to eased may be only 2.5–5 cm of sheet, so mark it.
- Boom height
- About 17.5–20.5 cm (7–8″) off the deck at the transom in moderate air; closer in heavy air, higher as it gets lighter.
- Outhaul
- Near the band in very light flat water; ease no more than 3.8 cm (1½″) as conditions build; back to the band at about 14 kn.
- Cunningham
- Just enough to remove luff wrinkles; more in heavy air to open the top of the main, eased promptly when it lightens.
- Lower backstay
- None in very light air, more as wind and waves build; tight for power in moderate to heavy air, eased to bleed power.
- Upper backstay
- On when overpowered to bend the mast, flatten and open the main and tighten the headstay; off promptly as it lightens.
- Side bend
- Sight up the mast upwind: a little leeward sag at the spreaders adds power in light air; more lower-shroud tension pulls the middle to windward and depowers in heavy air.
- Mast bender
- Neutral in all conditions; you can try a little forward bend in very light, flat water.
- Jib halyard
- Raising the tack works like moving the lead forward, lowering like moving it aft. Jib cunningham only to remove wrinkles. Keep the upper leech telltale flowing, especially in light air or chop.
- Helm
- Aim for an almost balanced helm with slight weather helm; North advises erring towards depowering because the Star is nearly always overpowered.
- Rake figures inside the guide disagree: 93–96 cm in the text, 94.5–97 cm in the table. Table rakes are for newer boats; older boats about 2 cm shorter.
- The jib athwartship figure is 36.5 cm in the text and 35.5 cm in the table (14″ is about 35.5 cm); the heavy-air cell is garbled in the source.
- Imperial and metric don't match for the jib car (7′ ½″ is about 214.6 cm, not 217 cm) or the text's 7′ 2″ (215 cm); the butt figures are printed in cm but are evidently mm.
- The guide states no wind units.
North Sails — Star Trimmanleitung (German, by Hans Spitzauer) Undated
- Written for
- Current North Star mainsails (the spreader setting is given for all of them); no model names
- Tension gauge
- Loos PT-1
- How it’s measured
- Intermediates (Mittelwanten): mast on two trestles (at the jib-halyard point and at the lower measurement band), groove down; pull the uppers (Oberwanten) down the front of the mast with a 15 kg spring scale and pencil-mark the inside lower end of the terminal; repeat for the intermediates. Spreader sweep (Salingswinkel): thin rubber band between the slightly backed-out spreader screws, shrouds not fitted, measured to the mast face, not into the groove. Rake (Mastfall): on a continuous forestay, pull it tight along the mast rig-down and mark the forestay at the lower end of the black measurement band; if the forestay is joined above deck, measure on the pin instead (values 43–47). Mast foot: measured with a batten from the transom to the mast foot. Shrouds read with the PT-1 after putting 10 units on each upper backstay (Oberbackstag), with no puller on and the lower backstays (Unterbackstagen) slack.
- Source
- North Sails, Undated
Base setup
- Intermediates
- Upper-to-intermediate difference 73 cm in the text (the sketch shows 73 mm, so mm is meant); lighter crews 72–71
- Spreader sweep
- 135 mm, a good start for all current North mains; more sweep = flatter, less = fuller. Half a turn of the Allen key each side moves it about 1 cm.
- Mast foot
- Depends on keel position (E measurement on the measurement certificate); the further forward the keel, the further forward the mast. Standard figures: Mader (older generation) and Folli 4520 cm, Lillia 4540 cm (as printed; the side-view sketch shows 4.522 m, so mm is meant). Ask the builder if unsure.
- Upper backstays
- 10 units each on the PT-1
- Shroud cars
- Lowers (Unterwanten) in line with the front of the mast; uppers can be run 5–8.5 cm from the lowers. On boats without levers or sliders the further-forward position is better because the uppers then slacken downwind.
- Rake start (Mastfall)
- Folli and Mader (old model) 43; Lillia and Mader (new) 44; mark at least two more settings 1 cm apart so the mast can be raked further when needed. Rake is right when, in 8–10 kn, the main can be sheeted hard enough for the top batten to come to windward (overtrimmed).
- Uppers base
- 22 on the PT-1 with the rake at 43/44 and 10 units on the backstays; check the Starmasters show the same numbers both sides (then the mast usually stands straight)
- Lowers base
- Mark 91.5 cm above the top edge of the black band; measured at right angles to the mast, 75 cm between the lowers (the medium-air setting with uppers at 22). A rubber band round the lowers keeps the pull consistent.
Trimmeinstellungen by wind (OW = uppers on Loos PT-1; other units as printed, mostly not stated)
| Wind | Uppers (OW) PT-1 | Lowers spacing (UW) | Rake (MF) | Jib car fore/aft | Jib car athwartships (Focktraveller) | Jib tack above deck | Jib halyard tension | Outhaul (Unterliek) | Cunningham |
|---|---|---|---|---|---|---|---|---|---|
| 0–5 | 21 | 74 | 44 | 217 | 40 | 2.5 | Slight wrinkles | 5 cm | None |
| 5–10 | 22 | 75 | 44 | 217 | 35 | 2.5 | Slight wrinkles | 5 cm | None |
| 10–15 | 22 | 75 | 44 | 217 | 35 | 2.5 | Wrinkle-free | 2.5 cm | Only to pull out wrinkles |
| 15–20 | 23 | 77 | 45 | 217 | 35 | 2.5 | Wrinkle-free | Full (voll) | Pull out wrinkles and hold (fixieren) |
| 20–25 | 23 | 79 | 45 | 219 | 37 | 2.5 | Wrinkle-free | Full (voll) | Full (voll) |
| 25+ | 24 | 79 | 46 | 220 | 40 | 2.5 | Wrinkle-free | Full (voll) | Full (voll) |
Trim by condition
- Spreader squareness
- With the rubber band still across the spreaders, fix a long batten at the mast foot, step back and sight that band and batten are parallel; correct by turning one screw out and the other in by the same amount so the sweep doesn't change. Half a turn each side changes the sweep by about 1 cm.
- Marks
- Mark jib halyard, jib traveller, backstays, outhaul and vang so settings can be repeated, and log settings against conditions and speed.
- A separate, undated North edition in German (North Sails One Design branding; contact details of Hans Spitzauer), hosted by the Austrian Star fleet. Its spreader, butt, rake and shroud numbers differ from the English North web guide.
- Several lengths are printed in cm where mm is clearly meant (73 cm intermediates vs 73 mm in the sketch; 4520/4540 cm butt vs 4.522 m in the sketch).
- Rake (MF) values 43–47 are those the text gives for measuring on the forestay pin; the forestay mark for continuous stays is put at the lower end of the black band (the English North guide uses the top of the band). The side-view sketch labels the rake dimension "43 cm (90 cm)" without explaining the bracketed figure.
- Table units are not stated for lowers, rake, jib car and tack height; the jib-car sketch shows 220 cm fore/aft and 35.5 cm athwartships from the deck/forestay intersection, so cm is likely.
Quantum Sails — Star Tuning Guide 2003 (Quantum San Diego, Mark Reynolds and George Szabo) 2003
- Written for
- Quantum Star main and jib (yarn-tempered Dacron)
- Tension gauge
- Small-model Pro Loos gauge, with equivalents on the old silver Loos gauge; backstays at 5 units on the Loos
- How it’s measured
- Intermediates, mast down: mark the upper's bearing point (include the small spacer on Spar Tech masts) and set the intermediates' inside bearing point to a second mark below it. Spreader sweep from the mast to a line between the tips at the shroud bolts. Rake as jibstay length, clevis pin to deck. Shrouds read with 5 units on the backstays, mast bender neutral, spreaders back.
- Source
- Quantum Sails, 2003
Base setup
- Intermediates
- 73 mm (2⅞″) to 76 mm (3″); quick guide suggests starting at 2 15/16″ (75 mm), text says most are now 74 mm (2 15/16″). Looser is better in light air and chop.
- Spreader sweep
- 127 mm (5″) to 139 mm (5.5″); text: about 127 mm (5″). More sweep needs more lower backstay but bends more easily in light air.
- Uppers
- 23–24 on the Pro Loos (31–32 on the old silver Loos): tight enough that they just slide on the tracks with the mast laid fully forward
- Lowers
- 915 mm (36″) up the mast from the top of the boom band, then shroud to shroud close to 735 mm (29″); lighter crews or steady moderate wind may tighten a little
- Partner
- At least 3 mm (⅛″) clearance each side of the mast
- Mast butt
- Quick guide 4500 mm (14′9″). Folli standard 4502 mm (14′ 9¼″) from the transom/deck intersection to the centre of the aft mast-step bolt; light crews a little forward.
- Butt check
- With jibstay and backstays set, the forward edge of the outhaul boom band is even with, or up to 38 mm (1.5″) past, the stern (author's Folli 35 mm behind; Mader about even)
- Shroud cars
- Lowers just in line with the front of the mast; uppers 1–2″ forward of the lowers
- Jibstay (rake)
- Quick guide: about 410 mm (16″) to 435 mm (17″), most new boats near 435. Text: 384 mm (15″) to 435 mm (17″) clevis pin to deck; Melges and Gerard about 406 mm (16″), Folli, Lillia and Mader about 432 mm (17″); author's 429 (16⅞″).
- Boom height
- About 200 mm (8″) off the deck in 8–10 kn (quick guide); 152–203 mm (6–8″) in medium air, 203–305 mm (8–12″) in light air (text)
- Jib
- Spreader mark 458 mm (18″) from the side of the mast; lead about 2200 mm (86.5″) from the headstay; cars 356 mm (14″) from centreline (9.5°); tack about 25 mm (1″) off the deck
- Backstay lengths (new mast)
- Lower 305 mm (12″) longer than the boom band, upper 165 mm (6.5″) shorter, on the author's system
Backstays by condition
| Condition | Lower | Upper |
|---|---|---|
| Upwind, light and lumpy / crew in cockpit | No tension (just enough to stop the rig swinging) | No tension either |
| Upwind, crew on deck | A little | Just snug |
| Upwind, crew hiking | More | Just snug |
| Upwind, overpowered | May ease slightly; very hard at times | Pull on; very hard at times |
| Reach without pole | — | Eased about 75 mm (3″) at the deck, about 230 mm (9″) on the line |
| Run, light to medium | Coarse adjuster eased about 1525 mm (60″) on a 3:1 system, until the spreaders start to reverse | Same |
| Run, strong wind | Not as far | Not as far |
Trim by condition
- Mainsheet
- Line the top batten up with the boom; it hooks slightly in very light air and twists off in heavy air. Trim harder in the groove and in flat water, ease out of tacks and in chop. Mark the sheet.
- Outhaul
- Small range: to the band above 10 kn or whenever overpowered; ease 25 mm (1″) in lighter air, a little more in chop. About 12:1 cascade purchase.
- Cunningham
- Horizontal wrinkles up to about 8–10 kn; tighten as it builds; completely loose offwind.
- Vang
- Top batten in line with the boom; firm on reaches; very little on runs.
- Mast lever
- Normally none upwind; on reaches only enough to stop reversing; on runs until the mast is straight with the windward spreader square.
- Jib
- Leech on the spreader mark in all but the lightest and windiest conditions (under 18 kn on the mark, slightly outside it in more wind); middle batten straight back, foot not too tight. Jib as low as possible.
- Rake
- Leave it alone once set: changing it alters halyard, leads, backstays and mainsheet.
- Purchases
- 5:1 on the lower backstay and 8:1 on the upper on the authors' boat.
- Older edition, written around Folli boats and the track and under-deck backstay systems of the time; rake is measured as jibstay length to the clevis pin, not to a black-band mark as in the 2020 guide.
- Inside the guide 2 15/16″ is given as 75 mm in the quick guide and 74 mm in the text, and the jibstay range is 410–435 mm in one place and 384–435 mm in another.
- The authors note that even the newer Pro Loos gauges can read up to 2 units apart, and the old silver-Loos equivalents are only given for the uppers.
- Also includes a crewing article by Magnus Liljedahl (no tuning numbers).
Star Class (Bill Buchan) — Thoughts on Upwind Speed Starlights, November 1980 (archive article)
- Written for
- Not stated
- Tension gauge
- Not stated (no tension numbers)
- How it’s measured
- Rake is set by feel: the most rake that still lets the main be trimmed hard in 10–12 kn.
- Source
- Star Class (Bill Buchan), Starlights, November 1980 (archive article)
Base setup
- Boom band
- About 3–4″ beyond the transom, with about 4″ of prebend from the lever
- Jibstay at deck
- Within about 1″ of fully aft of point A
- Shroud cars
- Lowers roughly in line with the mast face; uppers about 3–6″ ahead of the lowers
Trim by condition
- Rake
- A little more in light air, less at 12–18 kn, much more above 25 kn.
- Rig tension
- Slightly looser than his previous year's setup; backstays hard when a tight jibstay is needed.
- Jib
- Sight from under the boom to the clew: the lowest batten slightly to windward of a line from the leeward cockpit coaming.
- Keel and rudder
- Keel fin near ¾″ minimum thickness with maximum thickness about 4″ back; check keel alignment against a mark 48″ straight down from the stem knuckle; rudder near 1⅛″ maximum thickness at about 30% chord.
- Historical 1980 article (Buchan later won the 1984 Olympic Star event, as the 2003 Quantum guide recalls), kept on the Star Class site; useful context, not a modern setup.
- The same text also appears, titled "Some Thoughts on Upwind Speed", on the starclass.org history page "Tuning the Star", alongside 1966–67 articles by Malin Burnham and Lowell North that describe obsolete rigs (main traveller, older spreader set-ups) and were not added.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Star resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Star by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Star class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRules of the ISCYRA (updated January 2023), all parts
- Class associationstarclass.org
- Builder specificationsStar on mader-boote.de
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Star part