One-design race shop · Multihull
Dart 15 (Sprint 15) Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Dart 15 (Sprint 15)
All Dart 15 (Sprint 15) equipment
1 part
Fit verified for Dart 15 (Sprint 15)
Schaefer
Schaefer Wind Indicator - Cat Hawk
Part # SCHH005F00
$93.00
No Dart 15 (Sprint 15) parts match these filters.
Can’t find a part for your Dart 15 (Sprint 15)? Request a Dart 15 (Sprint 15) part
Go fast
Dart 15 (Sprint 15) tuning guide
The Dart 15 (called the Sprint 15 from 2005 to 2022) is a one-design cat with few adjustments: the shroud-pin hole sets rake, a rope forestay adjuster sets rig tension, and batten tension, downhaul and traveller do the rest. No sailmaker publishes a guide; the UK class association's tips are the reference, Windsport's rigging manual gives the starting shroud hole, and a 2012 Shanklin Sailing Club survey records what 20 boats there ran. There is no gauge reading anywhere; tension is judged by feel or as inches of forestay pull.
UK Dart 15 Association (Paul Smith) — Stay Tooned! April 1997
- Written for
- Standard Dart 15 una-rig mainsail
- Tension gauge
- None: rig tension by forestay adjuster and feel
- How it’s measured
- Rake is changed one shroud-pin hole at a time; rig tension is described as inches of extra forestay pull.
- Source
- UK Dart 15 Association (Paul Smith), April 1997
Base setup
- Rake
- Very little aft rake for 15 kn or less on flat water
- Crew position
- Sit right up against the windward shroud on all points of sailing
- Traveller
- Directly below the clew, except when the sail is fully out on a broad reach
Settings by wind
| Setting | Up to 7–8 kn | 8–18 kn | 18 kn + |
|---|---|---|---|
| Forestay / rig tension | Fairly slack, just enough to keep the shrouds straight (up to 8 kn) | Forestay another inch tighter | Another inch, until the shrouds are hard to push in with your fingertips |
| Batten tension | None (7 kn or less): sail as flat as possible | About ½" more on each batten (less on the top one) to induce a permanent curve; this band runs 8–20 kn | None again above 20 kn |
| Downhaul, beating | Just remove horizontal creases | Just remove horizontal creases (to 18 kn) | As much as possible |
| Rake | Little aft rake on flat water | Little aft rake on flat water (to 15 kn) | Pins down one hole and re-tighten the forestay (also in chop) |
Trim by condition
- Rake
- Raking back one hole helps pointing in most winds and off the wind in a breeze; one hole is usually enough.
- Mainsheet
- Beating under 8 kn, pull the mainsheet block-to-block to add rake. Fully eased off the wind, the masthead moves forward.
- Downhaul off the wind
- Reaching: ease until creases just start to appear. Broad reaching: fully off. Not on the run (the sail S-bends and can gybe). In strong winds leave it fully on.
- Trim fore and aft
- Beating: leeward bow's inside waterline just below the surface, windward hull just clear. In strong wind or chop sit further back and out so the bow doesn't bury. With a fairly upright mast the boat nose-dives more off the wind above 18 kn, so the helm needs to be about 13 stone or more, or sit on the rudder.
- Light-air battens
- Battens reverse more easily when tacking in light winds.
- Class-member tips rather than a sailmaker guide; no shroud-hole numbers are given as a base.
UK Dart 15 Association (George Carter) — Sailing in a Blow / Forestay Rig Tension June 1997 (class magazine article); forum answer 3 Feb 2009
- Written for
- Standard Dart 15 mainsail
- Tension gauge
- None
- How it’s measured
- Mast-rotation feel is used to judge forestay tension.
- Source
- UK Dart 15 Association (George Carter), June 1997 (class magazine article); forum answer 3 Feb 2009
Base setup
- Shroud pins
- 3rd hole from the top, never changed (Carter, forum answer)
- Forestay
- Rope adjuster at the bottom of the forestay pulled to maximum while the wind can still rotate the mast
- Rotation check
- Light wind: mast rotates easily to 90°. Medium: rig tightens just before 90°. Strong: tightens well before 90°.
Trim by condition
- Rake in a blow
- Raking back made no real difference to nose-diving and limits mainsheet trim.
- Downhaul
- On as hard as possible before the start (use the 3:1); ease on the run only if the bows won't bury.
- Battens
- Reduce tension progressively from the top down; very little tension from about Force 5.
- Traveller & mainsheet
- Note the traveller position before the start and set it so the boat is powered without constant luffing; end of the track on the first reach. Sheet hard upwind; ease about a foot when tacking (a couple of feet if it stalls). The class's upwind tips put the traveller 3–4" off midships.
- Crew position
- Hard against the shroud upwind, moving back if the leeward bow digs; right back on the first reach.
- Forestay adjuster (Supercharge tips)
- If a furling drum is fitted, have the forestay shortened by 2" and make up the length with a thin rope (about 1 m of 3 mm Dyneema), so rig tension can be set looser for light and tighter for strong winds.
- Rudder alignment (Supercharge tips)
- With the blades down, the distance between them at the front and at the back should match within a couple of mm.
- The forestay notes come from https://dart15.co.uk/faq/forestaytension.php, the traveller figure from https://dart15.co.uk/faq/upwind.php, and the Supercharge tips from Carter's 'Supercharge Your Dart 15' (https://dart15.co.uk/faq/SuperchargeYourBoat.pdf).
- Carter's forum answer adds that he uses tighter rig settings when sailing with the jib and trapeze.
Windsport International — The Forgotten Control (batten tension) December 2021 (upload date in the URL; signed "Tom")
- Written for
- Sprint/Dart 15 and Dart 18 mainsails
- Tension gauge
- None
- How it’s measured
- Mark each batten where the leech sits on it so the tension can be repeated.
- Source
- Windsport International, December 2021 (upload date in the URL; signed "Tom")
Base setup
- Minimum
- Just enough tension to remove the small vertical creases along the batten pocket
Trim by condition
- Deep vs flat
- More batten tension: deeper, more powerful sail for acceleration in light air, chop or waves. Less: flatter, lower-drag sail with more top speed. Too deep in very light air can hook the leech and stall.
- Order & method
- Work from the top batten down (short top battens need harder pulls). Brace the batten end on the traveller track, tie half a reef knot, pull in the tension, then lock it.
- After sailing
- Release the tension so the pockets don't stretch.
- Written by the builder's representative for both Dart 18 and Sprint 15 owners.
Windsport International (builder) — Sprint 15 Rigging Manual, Part 2 PDF dated February 2022
- Written for
- Standard Sprint 15 mainsail (7 battens) and optional roller jib
- Tension gauge
- None
- How it’s measured
- Shroud setting by vernier-adjuster hole; no rake measurement given.
- Source
- Windsport International (builder), PDF dated February 2022
Base setup
- Shroud adjusters
- Vernier adjuster on hole No. 1 from the top when rigging
- Battens
- No. 1 at the bottom to No. 7 at the top; thumb-and-forefinger tension, just enough to put a little tension down the pocket
- Mainsail downhaul
- No luff tension when hoisting; set it once sailing
- Jib (if fitted)
- Tension the luff with the jib downhaul; only furl or unfurl when the mainsheet is not loaded
- An assembly manual: the hole-1 shroud setting is a rigging start point. The class tips run lower holes (Carter keeps the 3rd hole), and the 2012 Shanklin survey shows holes 2–6.
Shanklin Sailing Club — Sprint 15 boat setup survey (Measurements) 13 August 2012
- Written for
- Standard Sprint 15 mainsail
- Tension gauge
- None: forestay figure given in inches (one boat also lists a pull in lbs)
- How it’s measured
- Rake: main-halyard shackle pin to the top of the traveller track on the rear beam. The page says the forestay figure is taken from the furling gear to the base of the mast; it doesn't say how.
- Source
- Shanklin Sailing Club, 13 August 2012
Settings recorded on 20 boats, 13 Aug 2012
| Sailor | Boat no. | Shroud pin hole from top | Rake (ft/in) | Rake (mm) | Forestay pull | Forestay (in) |
|---|---|---|---|---|---|---|
| Ian Bolton | 1698 | 3 | 22' 6.5" | 6870 | — | 12 |
| Liam Thom | 554 | 3 | 22' 6.75" | 6877 | — | 12 |
| Simon Giles | 1944 | 5 | 22' 6" | 6858 | — | 10 |
| Bob Marks | 1960 | 3 | 22' 6.25" | 6864 | — | 11 |
| Stuart Pierce | 1813 | 3 | 22' 6.25" | 6864 | — | 14 |
| Christine Roman | 1925 | 3 | 22' 6.25" | 6864 | — | 12 |
| Mark Pritchard | 1907 | 5 | 22' 6.25" | 6858 | — | 12 |
| Chris Read | 642 | 3 | 22' 6.5" | 6870 | — | 11 |
| Erling Holmberg | 2007 | 3 | 22' 5.5" | 6845 | — | 12 |
| Phil Davis | 1990 | 5 | 22' 5.75" | 6850 | — | 10 |
| Geoff Howlett | 1953 | 4 | 22' 5.75 | 6850 | — | 15 |
| Keith Newnham | 1150 | 3 | 22' 6.75" | 6877 | 6.5 lbs | 9 |
| Sean Strevens | 1779 | 2 | 22' 5.125" | 6835 | — | 15 |
| Bob Baker | 1926 | 4 | 22' 5.5" | 6845 | — | 11 |
| John Shenton | 1956 | 4 | 22' 4.5" | 6820 | — | 15 |
| Stuart Dyer | 1739 | 3 | 22' 4.5" | 6820 | — | 16 |
| Liam Thom | 1890 | 3 | 22' 4.25" | 6812 | — | 14 |
| Sean Mckenna | 1728 | 5 | 22' 6" | 6857 | — | 13 |
| Paul Grattage | 1458 | 6 | 22' 3.5" | 6795 | — | 22 |
| Alan Howie-Wood | 1704 | 5 | 22' 6.75" | 6877 | — | 13 |
- A snapshot of what boats at one club ran, not a recommendation. The headers are stacked over three rows in the page's table ("shroud pin / hole from top", "feet/inches" and "mm" under arrows for the rake, "forestay / pull", "forestay / inches"); read by table cell position, the labels above follow them. Only Keith Newnham's row has a value in the "forestay pull" column.
- The mm and ft/in rake columns don't always agree exactly (e.g. Mark Pritchard 22' 6.25" = 6858 mm); both are as printed. Liam Thom appears twice with different boats.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Dart 15 (Sprint 15) resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Dart 15 (Sprint 15) by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Dart 15 (Sprint 15) class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesDart-15 class Rules updated 070823 (filename); rules page labeled Updated June 2018; rules page https://dart15.co.uk/rules/class_rules.php
- Class associationdart15.co.uk
- Builder specificationsDart 15 (Sprint 15) on dartcatamaran.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Dart 15 (Sprint 15) part