One-design race shop · Multihull
Weta Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Weta
All Weta equipment
42 parts
Fit verified for Weta
Ronstan
Ronstan Standing Rigging - Stay Adjuster Channel Style - Length: 4/6 in (117 mm)
Part # RONRF2330
$29.77
$35.02Fit verified for Weta
Ronstan
Ronstan Spars, Fittings & Accessories - Mast Tang - Pin: 0.2 in (5 mm)
Part # RONRF43A
$24.79
$29.17Fit verified for Weta
Ronstan
Ronstan Swivel Cam Cleat - Base w/ Small C-Cleat & Fairlead - Line: 3/32 to 5/16 in (2 to 8 mm)
Part # RONRF67
$71.94
$84.64Fit verified for Weta
Ronstan
Ronstan Series 30 BB OrbitBlock, Single, Lashing Head, Becket Option
Part # RONRF35101
$17.26
$20.30Fit verified for Weta
Ronstan
Ronstan Cam Cleats - Fairlead w/ Front Mount (Grey) - For Small C-Cleat & T-Cleat
Part # RON-RF5005
$9.91
$11.66Fit verified for Weta
Ronstan
Ronstan Cam Cleat - C-Cleat (Small) - Grey - Line: 5/64 to 5/16 in (2 to 8 mm)
Part # RONRF5000
$29.77
$35.02Fit verified for Weta
Ronstan
Ronstan Shock - 3/16" Line - 1/4" Webbing - Grey - Pair
Part # ronrf8080gry-2
$23.10
$27.18Fit verified for Weta
Ronstan
Ronstan Shock - 3/16" Line - 1/4" Webbing - Red - Pair
Part # ronrf8080r-2
$23.10
$27.18Fit verified for Weta
Ronstan
Ronstan Cam Cleat - C-Cleat (Medium) - Grey - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # RONRF5010
$32.85
$38.65Fit verified for Weta
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for Weta
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for Weta
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for Weta
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Weta
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Weta
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Weta
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Weta
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Weta
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Weta
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for Weta
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Weta
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Weta
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for Weta
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Weta
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Weta
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for Weta
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No Weta parts match these filters.
Can’t find a part for your Weta? Request a Weta part
Go fast
Weta tuning guide
The Weta trimaran is designed to need very little tuning: no spreaders or diamonds, so set-up is mast rake (side-stay adjuster hole), plenty of forestay/rig tension, batten tension and the clew-board holes for main and jib, with downhaul and sheets doing most of the depowering. The builder's Tips and Tricks articles are the only published guides; none uses a tension gauge.
Weta Marine (Chris Kitchen) — Tips and Tricks: Upwind Sailing (Series 5) and Rigging Your Weta Right (Series 1) Series 5 October 2012; Series 1 August 2011
- Written for
- Weta main (boomless, fully battened), hanked jib and gennaker
- Tension gauge
- None (rig tension by feel: forestay until the beams stop rising in their sockets)
- How it’s measured
- Rake by the hole used on the side-stay adjusters (counted from the bottom). Jib tack ring height above the deck.
- Source
- Weta Marine (Chris Kitchen), Series 5 October 2012; Series 1 August 2011
Base setup
- Mast rake
- Side stays on the 3rd hole up from the bottom (about 30 mm) as a start; drop a hole if there's no weather helm. Aim for slight weather helm on both tacks; too much rake = rounds up easily, very heavy helm.
- Rig tension
- Plenty: tension the forestay until the beams stop rising in their sockets, then a fraction more; rig the same each time (forestay lashing length affects rake)
- Jib tack
- Bow ring about 50 mm above the deck with rig tension on; the three lines from the ring at roughly 120° to each other
- Battens
- Good tension, just starting to 'rib' the sail; ease only if really overpowered
- Trampolines
- Tensioned evenly; inner tension line set in line with its block plus about 5 cm extra
Clew-board positions by wind
| Wind (kn) | Main clew hole | Jib clew hole |
|---|---|---|
| Up to about 15 | Aft-most | Second from the back (aft-most or the one in front in light air) |
| About 15–22 | Middle (Series 1 says aft-most up to 18, middle 18–22) | Move forward a hole when overpowered / main backwinds |
| 22+ | Forward | Front hole by 25+; then ease the jib sheet if still overpowered |
Trim by condition
- Jib halyard
- Plenty: slight scalloping between hanks only in light air; none as the wind builds; at 18+ kn maximum, with tension lines up the luff. A 3:1 purchase (loop 150 mm from the cleat) helps; re-tension between races.
- Jib sheet
- Light air: twisted leech, all telltales flowing, under-sheet rather than pinch. Medium: as much sheet as possible without stalling; 3 mm of sheet changes the leech noticeably.
- Mainsheet
- Trim so telltales fly all the way up; stalled leeward head telltales = over-sheeted, stalled windward ones = under-sheeted.
- Cunningham
- A little from about 15 kn, building to maximum around 25 kn; if height drops, check tension in the bottom 3 battens or move the clew aft a hole.
- Steering and heel
- Windward hull flying; once fully powered on the rail, leeward float submerged to just above the horizontal join in the float. Adjust sail trim only for wind changes of about ±5 kn; otherwise steer.
- Crew position
- Light air: in the main hull just behind the mast; medium: on the rail just behind the side stay; over 18 kn about 30 cm aft of the side stay.
- Gennaker
- Halyard tension matters little; a tight furl reduces windage upwind.
- Series 1 (rigging) is at https://www.wetamarine.com/assets/Uploads/Weta-Trimarans-Tips-and-Tricks-Rigging-Your-Weta-Right-Series-1.pdf; it gives main clew aft-most to 18 kn, middle 18–22, front 22+, while Series 5 moves to the middle hole from about 15 kn.
- Series 1 says never to have scallops between the jib hanks; Series 5 (a year later) allows slight scalloping in light air.
Weta Marine (Miranda Powrie) — Tips and Tricks – Basic Tuning Guide (Series 9) April 2014
- Written for
- Weta main, jib and screecher
- Tension gauge
- None
- How it’s measured
- Rake by side-stay adjuster hole.
- Source
- Weta Marine (Miranda Powrie), April 2014
Base setup
- Mast rake
- Side stays in the 3rd or 4th hole from the bottom of the adjuster; tape the adjuster pin
- Sailing without the jib
- Side stays in hole 3 or 4 from the top (mast forward) so the boat bears away and tacks more easily
- Rig tension
- Forestay as hard as possible; some sailors tension the screecher hard then pull the forestay again
Trim by condition
- Clew holes
- Front holes (main and jib) twist and depower; back holes straighten the leech and deepen the foot for power.
- Screecher halyard
- Tight to flatten for tight reaching and in breeze (and for a good furl).
- Jib halyard
- Tighter when windy (a 2:1 purchase helps), looser in light air for depth.
- Battens
- Most sailors keep full batten tension in all conditions because downhaul and mainsheet depower the rig easily (general small-boat rule: loose in light and heavy air, tight in medium).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the Weta
Technical
Weta resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Weta by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Weta class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesnot stated (WCNA One-Design Rules adopted for 2019 seen in PDF; international draft 2017 V2.5)
- Class associationwetanorthamerica.com
- Builder specificationsWeta on wetamarine.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Weta part