One-design race shop · Keelboat

Yngling Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Yngling

  • 58 verified parts
  • 18 brands
  • Fit checked Nov 2026

Fit verified for Yngling

All Yngling equipment

58 parts

Can’t find a part for your Yngling? Request a Yngling part

Official Harken dealer

Yngling deck layout

Length
20 ft 4 in (6 m)
Weight
1320 lb (599 kg)
Beam
5 ft 6 in (1.6 m)
Draft
3 ft 6 in (1 m)
Mainsail
95 sq ft (8.8 sq m)
Jib
55 sq ft (5 sq m)
Spinnaker
180 sq f t (17 sq m)

Mainsheet

Mainsheet — Harken layout for the Yngling
Drawing: Harken
  1. 1 40mm Fiddle Block — SwivelHarken 2655 $52.95
  2. 4 40mm Block — SwivelHarken 2636 $38.95
  3. 5 29mm Block — SwivelHarken 340 $29.95
  4. 6 29mm Wire Bullet BlockHarken 098 $26.95
  5. 8 57mm Ratchamatic® Block — SwivelHarken 2625 $121.95

Belowdeck Fine-Tune Jib Controls

Belowdeck Fine-Tune Jib Controls — Harken layout for the Yngling
Drawing: Harken
  1. 2 13mm Car — Pivoting ShackleHarken 2700 $150.95
  2. 3 29mm Double Block — SwivelHarken 342 $53.95
  3. 5 29mm BlockHarken 348 $17.95
  4. 6 29mm Double Block — SwivelHarken 342 $53.95
  5. 7 29mm BlockHarken 348 $17.95
  6. 8 Standard Cam-Matic® Cleat - 150Harken 150 $44.95

Jib Halyard Adjuster

Jib Halyard Adjuster — Harken layout for the Yngling
Drawing: Harken
  1. 1 29mm Cheek BlockHarken 350 $18.95
  2. 2 29mm Cheek BlockHarken 350 $18.95
  3. 3 29mm T2 Soft-Attach BlockHarken 2146 $29.95
  4. 4 29mm T2 Soft-Attach BlockHarken 2146 $29.95
  5. 5 29mm BlockHarken 348 $17.95
  6. 7 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  7. 9 29mm Triple Block — SwivelHarken 344 $70.95
  8. 10 29mm BlockHarken 348 $17.95
  9. 11 29mm BlockHarken 348 $17.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Yngling tuning guide

The Yngling is set up with spreader length and sweep, mast position on deck, rake and cap-shroud tension, with the lowers tuned under sail for a little leeward sag in light air and a straight mast in breeze. All three guides use the Loos PT-1, but their cap-shroud numbers and rake methods differ (Ullman base 17 with rake to a forestay mark, North base 9 with rake to the transom, Høj Jensen 18.5 in medium air), so follow one guide at a time.

Ullman Sails — Yngling Tuning Guide (by Dayne Sharp) Two editions with identical numbers: 'Yngling Tuning Guide' (PDF dated August 2008) and 'Yngling Tuning Guide for Ullman Mainsail' (file name says 2008, PDF dated May 2015)

Written for
Ullman Yngling sails (one edition is titled for the Ullman mainsail); no sail models named
Tension gauge
Loos PT-1
How it’s measured
Spreader length from the mast side wall along the spreader to where the cap shroud passes the tip. Spreader rake: mast track up, shock cord clipped to the caps at the tips, measured at right angles back to the mast track. Rake: forestay laid tight along the front of the mast, marked at the top edge of the gooseneck black band; with caps and lowers slack, measure from the deck beside the forestay fitting up to that mark. Mast centred with a tape on the main halyard to each shroud base.
Source
Ullman Sails, Two editions with identical numbers: 'Yngling Tuning Guide' (PDF dated August 2008) and 'Yngling Tuning Guide for Ullman Mainsail' (file name says 2008, PDF dated May 2015)

Base setup

Spreader length
600–620 mm
Spreader rake
190 mm; can go to 225 mm for moderate winds (know how many adjuster turns this takes); check both sides equal against a batten on the aft edge of the heel
Mast position on deck
Two common positions: forward face of the mast at the cabin top 360 mm (most forward) or 280 mm from the forward breakwater measurement point
Mast heel
Start with a 1–2 mm gap at the front edge of an adjustable heel (range 1–3 mm to induce bend)
Rake
112 mm from the deck beside the forestay attachment to the forestay mark
Cap shrouds (setup)
17 on the PT-1, no lower or backstay tension; mast track straight
Prebend
20–25 mm (main halyard held to the track at the gooseneck, moderate tension)
Lowers (setup)
Just tight, even both sides; then tune under sail

Rig tension by wind (caps on Loos PT-1; lowers as leeward bend at the spreaders)

Wind (kn)Cap shrouds PT-1Lowers (leeward bend)
4–693 mm
6–8115 mm
8–10140 mm
10–14170 mm
14–18210 mm
18+250 mm

Trim by condition

Cap shrouds
Enough tension that the leeward cap just stops moving across the range; the numbers vary with crew weight and sea state.
Lowers
Set while sailing by sighting up the front of the mast on each tack; small changes matter and wrong tension costs pointing. Raise the lowers with the caps so the mast stays straight to the spreaders, otherwise vang tension over-bends it and creases the main. Ease the vang before sighting.
Spreaders
After stepping, check the tips are even (to the transom centreline or to a forestay mark at spreader height) and at equal height above the deck.
  • Ullman's own download page could not be opened; both editions are hosted by canadianboating.ca (mainsail edition: https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Yngling-Mainsail-Tuning-Guide-2008.pdf). The NTNU sailing club also links a copy.
  • The 4–6 kn row shows less leeward bend (3 mm) than 6–8 kn (5 mm), as published.
  • Mast position as printed: 360 mm is the most forward setting and the mast 'can be moved aft to 280 mm', although a smaller distance from the same forward reference would normally mean further forward; check against your boat.
  • Based on the author's seven years coaching women's Olympic Yngling campaigns.

North Sails — Yngling Tuning Guide Undated (current web page)

Written for
North Yngling main, jib and spinnaker (no model names)
Tension gauge
Loos PT-1
How it’s measured
Spreader length from the mast side to where the shroud passes the tip; cant from the back of the mast to a taut line between the tips. Rake: tape hoisted on the main halyard to the standard full hoist, measured to the deck at the transom; use the same tape to centre the mast.
Source
North Sails, Undated (current web page)

Base setup

Spreader length
Very close to 60 cm (23 9/16″)
Spreader cant
21.5–22.0 cm (8½–8¾″); Abbot boats with Proctor spars 21.6–21.8; DeWolf boats with Hall spars about 21.5 cm. More = bendier mast.
Mast step
Centre of the forestay pin to the front of the mast 1.925 m (6′ 3¾″); the mast should not sit flat on the step — leave nearly ¼″ so it can rock fore and aft
Rake
Masthead (halyard tape) to the deck at the transom 26′ 3″–26′ 5″
Uppers
About 6 in light winds (the guide says below 6 mph), about 9 as the medium-wind base, 18 in heavy breeze (PT-1, at the dock)
Lowers
Tuned under sail: about ⅜″ leeward sag at the spreaders in light to medium winds; tighter in breeze or when overpowered to straighten the mast
Jib lead
2 m from the forestay pin to the centre of the block

Upper shroud tension (Loos PT-1, dock readings)

WindUppers PT-1
Light (below 6 mph as printed)About 6
Medium (base)About 9
Heavy breeze18

Cunningham by wind

Wind (kn)Cunningham
Up to 10None
11–12Just enough to remove many of the wrinkles
Above 12Progressively tighter, removing most wrinkles

Trim by condition

Final check
In every condition the leeward upper should just start to go slack, not flop about.
Backstay
Bends the mast, flattening and opening the upper main, and tightens the forestay (flatter jib entry, less heel); recheck mainsheet and vang after every change.
Mainsheet
Top batten parallel to the boom; harder (slightly to windward) to point once up to speed, with the top telltale stalling about 70% of the time; ease in light air and chop.
Traveller
Light to moderate air: car up to 4–5″ to windward so the boom is on centreline, top batten near parallel (15–20° outboard of parallel in light or sloppy conditions). Back towards centre as it builds; up to 2–3″ below centreline when very windy.
Vang
Very windy: hard on to control leech and bend the lower mast. Downwind in light to moderate air: top batten just past parallel.
Outhaul
Tight enough to close the shelf foot in almost all conditions; to the band in heavy air (small difference).
Cunningham
Aim for maximum draft about 50% aft.
Jib
Luff should break nearly evenly at the 2 m lead; in heavy air move the lead aft one hole (no more than 1″). Many raise the tack 2–3″ with the skirt still on deck for a fuller foot. Halyard: just a hint of wrinkle at each hank, slightly tighter in heavy air.
Spinnaker
8–10″ of luff curl; pole end level with the free clew and square to the apparent wind; pole height so the luff breaks about a third down from the head (or centre seam parallel to the mast). Heavy-air reaching: pole at least 2–3″ off the headstay; ease 2–3′ of sheet as a puff hits.
Twings and downwind main
Windward twing fully down; leeward off for the set and in light air, about halfway (2′ off the deck) in very heavy air. Downwind ease cunningham, backstay and outhaul.
  • No date or author on the page; the light-air shroud band is printed in mph.
  • The old URL northsails.com/sailing/en/resources/yngling-tuning-guide redirects to the blog URL above.

Høj Jensen Sails — Yngling trim guide Undated (current web page)

Written for
Høj Jensen main, light jib, medium/heavy jib, spinnaker (sheeting figures given for boat DEN 136)
Tension gauge
Loos PT-1
How it’s measured
Rig length: stern of the boat to the main halyard hooked at the masthead. Jib sheeting point: from the jib's 'head attachment on the boat' (as printed; presumably the tack/forestay fitting on deck) to the middle of the sheeting block.
Source
Høj Jensen Sails, Undated (current web page)

Base setup

Stern to masthead (main halyard)
808 cm
Spreaders
Length 60 cm, angle 24 cm
Jib head shackle
40 mm long
Jib sheeting point (DEN 136)
196 cm in light air; 194 cm in medium/heavy
Jib halyard
Only until the luff wrinkles disappear, no tighter

Shroud settings (uppers on Loos PT-1)

ConditionsUpper shrouds PT-1Lower shrouds
Light10Middle of the mast 5 cm to leeward
Medium18.5Mast straight
Heavy25Top of the mast 5–10 cm to leeward

Jib choice

JibWind
Light jib0–5 m/s (0–12 kn)
Medium/heavy jib5–14 m/s (10 kn and up)

Mainsail outhaul (distance from the black band)

WindSmooth waterWaves
1–3 m/s5 cm from the band5 cm from the band
4–10 m/sOut to the band3 cm from the band
10+ m/sOut to the bandOut to the band

Trim by condition

Jib traveller in waves
One position forward in short, steep waves; one back as the wind increases. Upwind in waves, easing the sheet works better than moving the traveller.
Mainsail
Main trim is the key to the Yngling's basic setup; the main closes its leech when sheeted hard.
Backstay
Opens the top of the main; pull to neutralise too much weather helm, but too much costs height.
Main traveller
Slightly to windward in light air; centred in medium and heavy air.
Cunningham
Only in medium and heavy conditions.
Spinnaker
Pole at the highest position the class allows (lowest setting only in heavy air); horizontal or up to 10 cm above horizontal; on a reach 30 cm off the forestay in light air, 50 cm in medium/heavy; the foot must never touch the forestay.
  • The page is in English; its shroud table pairs each upper reading with a lower-shroud mast-bend instruction per condition (rechecked at audit).
  • Wind bands overlap in the jib-choice table (0–12 kn and 10 kn up), as published.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Yngling resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Yngling by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Yngling class rules before changing equipment, and ask your class measurer if a part is not original equipment.