One-design race shop · Dinghy

RS700 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

RS700

  • 47 verified parts
  • 11 brands
  • Fit checked Nov 2026

Fit verified for RS700

All RS700 equipment

47 parts

Can’t find a part for your RS700? Request a RS700 part

Go fast

RS700 tuning guide

The RS700 is set up within a minimum-to-maximum power window (rake 7060–7360 mm to the gudgeon, 150–220 kg on a shroud, spreaders and prebend matched to sailor weight), and normally only rake changes with the wind. The 2005 fleet survey measures rake to the transom 'bump' and tension on the forestay in pounds, so its numbers can't be compared directly with RS's own guide.

RS Sailing (LDC) — RS700 Rigging Guide – Tuning Guide section Undated (PDF dated March 2014)

Written for
Class main and asymmetric
Tension gauge
Rig tension gauge (model not named), kg measured on a shroud
How it’s measured
Rake from the tip of the mast to the gudgeon. Spreader length mast to shroud; sweep from the shrouds to the mast track.
Source
RS Sailing (LDC), Undated (PDF dated March 2014)

Base setup

Prebend minimum
50–60 mm so the sail sets in light winds
Rigging start
Lowers in the top hole of the chainplates; shrouds in the aft chainplates, hole three as a starting point; 220 kg on a shroud via the forestay purchase (don't push down on the boat)
Wing width
≤68 kg hole 4 (2.30 m, 9 kg lead); 69–77 kg hole 3 (2.20 m, 6 kg); 78–86 kg hole 2 (2.10 m, 3 kg); ≥87 kg hole 1 (2.00 m, none); add holes for shorter sailors per the guide's height table

Power window (rig tension measured on a shroud)

SettingMin powerMax power
Mast rake (tip of mast to gudgeon)7060 mm7360 mm
Rig tension (on shroud)150 kg220 kg
Spreader length (mast to shroud)400 mm450 mm
Spreader sweep (shrouds to mast track)220 mm140 mm
Prebend125 mm50 mm

Trim by condition

Rake by wind
Maximum power 7360 mm in 3–8 kn for everyone (heavier sailors hold it longer); minimum power 7060 mm (fully raked, flattener in, board raked) from about 16/18 kn for light sailors, 20 kn+ for heavier.
Tension and spreaders by weight
The 67–95 kg weight spread maps onto the min–max settings; at 80/85 kg and medium height, the middle is close.
Cunningham
Slack in light airs, progressively harder; extreme tension blades the upper leech in very strong wind.
Vang
More with more wind; ease in very gusty conditions and substantially downwind; a little in light airs adds shape.
Outhaul
Tight except in light airs (ease 1–2 cm for waves).
Foils
Rudder always fully down; daggerboard down on all points, raked when the rig is raked, raised a few inches in heavy wind.
  • RS's own site no longer hosts this file; the link is to a copy on a French skiff forum.

RS700 fleet (Stokes Bay open survey) — RS700 Rig Settings Guide – 2005 2005

Written for
Class sails
Tension gauge
Not named; tension measured on the forestay in pounds; lowers adjusted on the Sta-Master calibration scale
How it’s measured
Rake from the masthead to the top edge of the transom 'bump' with rig tension on. Prebend at maximum bend with rig tension on, line from masthead to bottom of the sail track. Lowers checked without the sail but with tension on.
Source
RS700 fleet (Stokes Bay open survey), 2005

Base setup

Rake
730–740 cm (normally hole 2–4 on the shrouds)
Rig tension (forestay)
450–550 lb; generally more is good; mark the setting
Spreaders
Base 79 cm between the shrouds and 18 cm from a line between the shrouds to the back of the mast track (bigger crews go wider)
Prebend
Most used 40–50 mm (range 10–90 mm among the top 5)
Lowers
About 4 cm lateral movement in medium conditions (roughly hole 3 on the back holes of the standard adjuster); change no more than '1' on the Sta-Master scale

Changing gears (wind in Beaufort force as published)

ConditionsMainsheetKickerCunninghamOuthaulBoardRake
Light (F0–1)Light; sheet in for gustsA little to flattenNoneMidDown (back elastic)Some reduce rake one hole
Max power (F1–2)Max, almost block to blockLotsA little (creases still up the luff)MidDown (back elastic)Normal
Overpowered (F2–4)Play lots, never block to blockMoreIncrease to depowerEase slightly to stop foot flutterSome rake (front elastic)Normal
Very overpowered (F4–6)Ease and play even moreEven moreLotsEase slightly to stop foot flutterRake (front elastic); some raise 5–10 cmRake one hole (reset tension, lowers, strop)

Trim by condition

Lowers
Loosen if the boat staggers however much kicker and cunningham you use; tighten if it feels loose and points poorly.
Mainsheet strop
Set nearly block to block with max sheet and some kicker, so the leeward strop slackens as kicker goes on.
  • A fleet survey from one 2005 event rather than a sailmaker guide; its rake reference and forestay tension aren't comparable with the RS guide's gudgeon rake and shroud tension.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

RS700 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the RS700 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current RS700 class rules before changing equipment, and ask your class measurer if a part is not original equipment.