One-design race shop · Dinghy
Contender Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Contender
All Contender equipment
19 parts
Fit verified for Contender
Davis Instruments
Davis Spare Vane f/WindTrak 10.Sport
Part # dav-3101
$29.99
Fit verified for Contender
Davis Instruments
Davis Windtrak Wind Vane Tab Assembly
Part # dav-r3102
$15.00
Fit verified for Contender
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Contender
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Contender
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Contender
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Contender
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Contender
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Contender
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Contender
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for Contender
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Contender parts match these filters.
Can’t find a part for your Contender? Request a Contender part
Go fast
Contender tuning guide
The Contender is a single-handed trapeze dinghy tuned with rake (tape from the masthead band to the transom), spreader length and deflection, pre-bend with the lowers slack, lowers then set to straighten the mast, and shroud tension; upwind the centreboard is progressively raised as the wind builds. The two published guides agree on 430 mm spreaders but quote rig tension differently (Loos 26–28 vs 115–150 kg on an unnamed gauge).
North Sails — Contender Tuning Guide Undated web guide
- Written for
- North Contender main (model not named)
- Tension gauge
- Loos (model not stated)
- How it’s measured
- Spreader angle measured from the track to a line stretched between the wires at the spreader tips. Pre-bend set with the lowers slack.
- Source
- North Sails, Undated web guide
Base setup
- Rake
- 21′2″
- Spreader length
- 430 mm
- Spreader deflection
- 100–110 mm (track to line between the wires at the tips)
- Pre-bend
- 20–25 mm with lowers slack
- Lowers
- Tension until the mast is straight
- Shroud tension
- 26–28 on a Loos gauge
Centreboard position upwind
| Wind (kn) | Board (from vertical) |
|---|---|
| 0–8 | Vertical |
| 9–12 | Up 5–8 cm |
| 13–18 | Up 10–15 cm |
| 19–25 | Up 20–25 cm |
Trim by condition
- Centreboard
- Exact heights depend on crew weight and height, mast stiffness and sea state. Raising it too far makes the boat easy but poor at pointing: lower it a little to point, raise it to go low and fast.
- North's page gives a single rake figure, not rake by wind.
Wavelength Designs — Contender Setup and Tuning Guide Undated web guide (linked from the International Contender Class site)
- Written for
- Wavelength standard Contender sail (leech cut 100 mm short of maximum)
- Tension gauge
- Rig tension gauge (model not named), in kg/lb
- How it’s measured
- Rake: tape hoisted on the halyard from the lower edge of the masthead measurement band to the transom crown, with lowers and rig tension on. Spreader deflection from the mast track to a straight edge joining the spreader tips.
- Source
- Wavelength Designs, Undated web guide (linked from the International Contender Class site)
Base setup
- Mast position
- Top of transom (excluding overlap) to aft face of the mast including the track, at deck level: as close to the 3050 mm minimum as possible
- Rake
- About 6500 mm (a compromise) with the standard sail; some top sailors use 6420 mm, which makes tacking very difficult; a few cm either way isn't critical
- Spreaders
- 430 mm long (leave fixed while learning); about 11 cm deflection to start. Swinging the spreaders forward straightens the mast, aft adds bend.
- Pre-bend
- 20 mm for an 80 kg helm; about zero for heavier helms; about 50 mm for a 70 kg helm
- Lowers
- Just taut, adjusted equally, with the forestay lever horizontal
- Rig tension
- 115 kg (250 lb) to 150 kg (340 lb) on a rig tension gauge, depending on body weight and mast type (heavier sailors generally more); too much in light air can stop the rig depowering later
- Reference marks
- Boom band 2700 mm from the aft edge of the mast track, with a mark 50 mm inboard; cunningham mark 50 mm below the track exit; mainsheet mark where it passes the boom block in medium conditions
Trim by condition
- Example: Force 3, flat water, straight-legged trapezing
- Outhaul on its reference mark; cunningham 1" above reference; vang 2" beyond reference; mainsheet at its reference mark; lowers one hole tighter.
- Halyard
- Use low-stretch halyard (the author uses 2.5 mm wire).
- The page carries no author byline or publication date (site footer © 2006–2026).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Contender resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Contender by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Contender class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesCurrent class rules
- Class associationcontenderclass.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Contender part