One-design race shop · Dinghy
Day Sailer Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Day Sailer
All Day Sailer equipment
26 parts
Fit verified for Day Sailer
Harken
Harken Block - Carbo 57mm Single - Swivel
Part # HAR2600
$55.95
$63.45Fit verified for Day Sailer
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Day Sailer
Harken
Harken Swivel Cam Cleat - Base (Small) w/ Cam-Matic 150 - Line: 1/4 to 5/8 in (6 to 16 mm)
Part # HAR205
$163.95
$186.05Fit verified for Day Sailer
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Day Sailer
Boomkicker
Boomkicker Spares – Eye Strap with Luff Slide – For K0400
Part # BOOM0440
$22.88
$24.96Fit verified for Day Sailer
Boomkicker
Boomkicker Spares – Mast Bracket – For K0400
Part # BOOM0420
$15.55
$16.96Fit verified for Day Sailer
Barton Marine
Barton Windicator WP285 – Offshore Racing
Part # bam-84004
$59.00
Fit verified for Day Sailer
Boomkicker
Boomkicker Spares – Mast Swivel – For K0400, K0500 & K0750
Part # BOOM0710
$21.05
$22.96Fit verified for Day Sailer
Boomkicker
Boomkicker Rigid Boom Vang - Inc. Fittings - Boat Size: 16 ft (4.9 m) to 19 ft (5.8 m)
Part # BOOK0400
$293.00
$346.95Fit verified for Day Sailer
Davis Instruments
Davis Spare Vane f/WindTrak 10.Sport
Part # dav-3101
$29.99
Fit verified for Day Sailer
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Day Sailer
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Day Sailer
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Day Sailer
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for Day Sailer
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Day Sailer
Schaefer
Schaefer Wind Indicator - Little Hawk Race
Part # SCHH007F00
$93.00
Fit verified for Day Sailer
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Day Sailer
Schaefer
Schaefer Wind Indicator - Little Hawk MK 1
Part # SCHH003F00
$34.70
No Day Sailer parts match these filters.
Can’t find a part for your Day Sailer? Request a Day Sailer part
Official Harken dealer
Day Sailer deck layout
- Crew
- 2
- Draft
- 3.75 ft (1.143 m)
- Type
- Monohull
- Construction
- Fiberglass
- Hull weight
- 575 lbs (261 kgm)
- LOA
- 16.75 ft (5.105 m)
- Beam
- 6.00 ft (1.829 m)
- Mast length
- 22.50 ft (6.858 m)
- Spinnaker area
- 95 sq ft (8.8 m2)
- Upwind sail area
- 145.0 sq ft (13.47 m2)
Spinnaker System
-
1
57mm Block — SwivelHarken 2600
$55.95 -
2
57mm Block — SwivelHarken 2600
$55.95 -
8
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
9
57mm Ratchet Block — SwivelHarken 2135
$86.95 -
14
Standard Low Profile Cam Base — SwivelHarken 205
$163.95 -
15
57mm Ratchet Block — SwivelHarken 2135
$86.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Day Sailer tuning guide
The Day Sailer's rake and rig tension are set once ashore (about 25′1″ to the transom with moderate shroud tension, or very tight via the forestay as some champions prefer), with spreaders trimmed to suit; on the water you sail with jib lead, sheet, outhaul, cunningham and vang. Only North's guide could be opened; Doyle's older guide survives only in Day Sailer forum posts, which are behind a bot check.
North Sails — DaySailer Tuning Guide Undated web page (current)
- Written for
- North Day Sailer main, jib and spinnaker
- Tension gauge
- Not named (shroud tension in pounds)
- How it’s measured
- Aft rake: tape hoisted on the main halyard, held at the transom/rear-deck junction, rig snug and jib down. Prebend: main halyard held at the gooseneck, gap to the back of the mast at the spreaders. Mast butt measured along the floor from the inside of the transom to the aft face of the mast.
- Source
- North Sails, Undated web page (current)
Base setup
- Aft rake (rig snug, jib down)
- 24′11″ to 25′1″ (printed as '24 11″ to 25′ 1″')
- Aft rake (jib up, rig pulled forward)
- 25′1″ to 25′2″
- Shroud tension
- About 150 lb; the leeward shroud should not go slack until about 10 mph. Rake and tension are set and not changed.
- Alternative (Dave Keran)
- Rig very tight using forestay tension only: rake 25′1″, forestay 200–210 lb, shrouds 300–320 lb
- Prebend
- About 1″ positive
- Mast butt
- Printed as 11′1/2″ from the inside of the transom to the aft face of the mast
- Spreaders
- Many masts start near 21½″; trim no more than ½″ at a time. Check with the spinnaker halyard: about ½″ gap at the chainplate and the spreader tip about 3½″ beyond the taut halyard.
- Jib lead (start)
- Lead block 9′3½″ aft of the jib luff wire, measured around the cuddy
Trim by condition
- Jib lead
- Fore and aft: telltales break nearly evenly (if anything the top slightly first); heavy wind: aft 2–3″; most boats use inhaulers that bring the sheet in to where it would cross the cuddy 16″ from centreline; in breeze: outboard and aft 1–1½″; very light, choppy air: outboard (printed as 'move your lead outboard 2″ to 18″ off centerline') and ease the sheet.
- Barber-hauler (Keran)
- Barber-haulers exit through-deck bullseyes on the aft face of the cuddy about 8″ from centreline and cross the boat; the block holds the jib sheet about 12″ off centreline, about 20″ from the bullseye, left floating rather than pulled down to the cuddy.
- Jib sheet
- Upper leech about 10° outboard in most conditions.
- Mainsheet
- Upper batten parallel to the boom; about 5° outboard in light air or chop; parallel to centreline when drifting (boom about 2 ft off); about 5° outboard above 15 mph.
- Cunningham / jib cloth
- Just remove horizontal wrinkles: a hint in the main and slight crow's feet at the jib snaps.
- Outhaul
- Foot bolt rope just standing up straight; nearly to the band in heavy air; ease 2–3″ downwind.
- Vang
- Downwind: telltale at the upper batten flying straight off the leech. Upwind in heavy air: upper batten no more than 5–10° past parallel to the boom.
- Mast bend check
- Upwind in 10–12 mph: a hint of diagonal overbend wrinkles below the spreaders, aiming at the clew; above 15 mph: more definite; above 20 mph: 'speed wrinkles'. Check side bend in about 8 mph (shorten spreaders if the mast sags to leeward at the spreaders); set spreader sweep so wrinkles barely show above the spreaders in about 10 mph; set the mast butt so the lower wrinkles just appear in 8–10 mph (butt aft = bendier low down).
- Spinnaker
- 6–12″ luff curl; 2″ sheet eases and trims; pole height keeps the centre seam parallel to the mast.
- Two printed numbers are ambiguous: the mast-butt figure reads '11′1/2″' (11′½″ or 11′1½″) and the light-air lead reads 'outboard 2″ to 18″ off centerline'. The page text gives no way to decide either; read against the guide's own 16″ inhauler crossing point, the lead wording would fit 'out 2″, to 18″ off centreline', but that is an inference, not something the page says. Confirm with North before cutting or drilling.
- Audit: Day Sailer forum threads that might settle the mast-butt figure (forum.daysailer.org) returned HTTP 403 and could not be read.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Day Sailer resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Day Sailer by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Day Sailer. Racing legality depends on your class or handicap rules; check them before changing equipment.
- Class associationdaysailer.org
- Builder specificationsDay Sailer on capecodshipbuilding.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Day Sailer part