One-design race shop · Keelboat

Nordic Folkboat Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Nordic Folkboat

  • 62 verified parts
  • 11 brands

Fit verified for Nordic Folkboat

All Nordic Folkboat equipment

62 parts

Can’t find a part for your Nordic Folkboat? Request a Nordic Folkboat part

Go fast

Nordic Folkboat tuning guide

Most Folkboat guides don't use tension gauges: they set rake by a forestay mark (or a plumb line), then control bend and forestay sag with how hard the mast foot is pushed against the aft edge of the mast hole, jumper turns and shroud turns, aiming for about 8 cm of forestay sag. Settings differ for aluminium and wooden masts and between sailmakers; Doyle's rake is measured a different way from North's, and the UK association's base settings add shroud loads in kg on an unnamed gauge, so don't mix numbers between guides.

North Sails — Nordic Folkboat Tuning Guide for Aluminium Masts Undated web guide (Søren Kæstel, Per Jørgensen, Theis Palm)

Written for
North Folkboat mainsail and jib
Tension gauge
Not used – tension is set by forestay sag and turnbuckle turns
How it’s measured
Rake: detach the forestay, lay it up the mast, stretch it and mark it level with the top of the gooseneck mark; reattached, the mark is measured to the deck along the forestay. Centring: mark each shroud at the same height and compare mark-to-deck distances.
Source
North Sails, Undated web guide (Søren Kæstel, Per Jørgensen, Theis Palm)

Base setup

Mast rake
Forestay mark 1.31 m from the deck along the forestay
Mast foot
Slide aft until the mast just touches the aft edge of the mast hole, then press further aft on the foot rail by wind (see table)
Jumpers
Pull on backstay, sight up the track; mast straight and jumpers equal. Fairly loose in light and strong wind; tighten the common turnbuckle 2–3 turns in medium wind.
Mainsail draft
Maximum draft in the top of the main 47% aft along the chord; aim for an even mast curve from deck to top
Forestay sag
About 8 cm in light wind, achieved by tightening the shrouds while sailing
Jib lead track
Centre 58 cm from the boat's centreline (cabin-top sheeting recommended)
Jib lead reference
2.65 m from the forestay pin to the centre of the block (lead on the cabin top)

Mast foot and shrouds by wind

WindMast foot pressed aft on railJumpersShrouds
Light 0–8 kn22 mmRelatively looseSet for about 8 cm forestay sag
Medium 9–14 kn16 mmCommon turnbuckle +2–3 turns+1½ turns
Strong10 mmRelatively looseA further +1½ turns

Mainsail controls by wind

ControlLightMediumStrong
Outhaul0–5 kn: 3 cm from the mark5–12 kn: about 1.5 cm from the markAll the way to the mark
CunninghamOffJust remove luff wrinklesOver 15 kn: pulled hard
Traveller (twin cars)0–6 kn: cars 15–20 cm to windward6–14 kn: centredEased to leeward to cut heel and helm

Trim by condition

Mainsheet
Main shape control: harder closes the leech and adds helm but helps pointing (medium wind, flat water); ease in light air so the top telltale flies; in heavy air sheet hard and add backstay until the helm is light; more twist in big waves. Top batten parallel to the boom in almost all winds.
Traveller set-up
Two cars joined by two wires of about 40 cm to the mainsheet block.
Backstay
Flattens the main, opens the leech and reduces forestay sag (flatter jib). Mark it, e.g. every 20 cm.
Kicker
Upwind only in strong wind; never upwind under 18 kn. Always ease before bearing away. Downwind set so the top batten is parallel to the boom.
Jib sheet
Middle batten parallel to the centreline in most conditions; 2–3° more twist in 0–5 kn. In lumpy seas move the lead 2–3 holes forward; in heavy wind 2 holes back without letting the foot flutter.
Jib halyard
Just remove luff wrinkles; leave small wrinkles in light air.
Jib lead
Luff should break evenly – top and bottom telltales together. Use a swivel block on deck when sheeting from the cabin top.
  • The web guide gives the kicker limit as 18 kn; North's 2023 presentation of the same guide says 16 kn.

North Sails — Nordic Folkboat – Helsinki spring 2023 (North Sails Folkboat sails and tuning) Spring 2023 presentation; file name TheisPalm26042023 (26 April 2023). The guide text inside credits Søren Kæstel, Per Jørgensen and Theis Palm.

Written for
LM-5A mainsail (J.M aluminium mast); LM-5 mainsail (B.M aluminium mast and most wooden masts); FL-5L jib 0–12 kn; FL-5 jib 8 kn and up (the all-purpose choice if you have only one jib)
Tension gauge
Not used
How it’s measured
Same method as North's aluminium-mast guide, plus a check that the gooseneck mark is 1 m above deck (±1 cm in the rules).
Source
North Sails, Spring 2023 presentation; file name TheisPalm26042023 (26 April 2023). The guide text inside credits Søren Kæstel, Per Jørgensen and Theis Palm.

Base setup

Mast rake
Forestay mark 1.31 m from the deck along the forestay
Gooseneck mark height
1 m (±1 cm in the rules)
Mast foot
Light 0–8 kn 22 mm aft on the rail; 9–14 kn 16 mm; strong 10 mm
Jumper struts
Legs not less than 450 mm ±5 mm; 900 mm ±10 mm between bearing points (standard on J.M and B.M masts)
Jumpers
Loose in light and strong wind; common turnbuckle +2–3 turns in medium
Forestay sag
About 8 cm in light wind; shrouds +1½ turns medium, +1½ more strong. Check: with a medium set-up the forestay moves 28 cm from full starboard to full port.
Jib lead
Track centre 58 cm from centreline; 2.65 m forestay pin to block centre
Whisker (jib) pole
2,85 m

Crew weight placement upwind

WindPlacement
4–7 knOne crew in the cabin forward, one to leeward trimming, helm to leeward
8–11 knBoth crew in the cockpit balancing the boat, helm to windward on deck
12 kn and upAll on deck, hiking as the wind builds

Trim by condition

Mainsail
Same notes as the web guide: outhaul 3 cm off the mark at 0–5 kn, 1.5 cm at 5–12 kn, at the mark above; cunningham hard over 15 kn; traveller cars 15–20 cm to windward at 0–6 kn, centred 6–14 kn; backstay marked every 20 cm.
Kicker
Never upwind under 16 kn; ease before bearing away; downwind top batten parallel to the boom.
Jib
Middle batten parallel to centreline; 2–3° twist in 0–5 kn; lumpy sea 2–3 holes forward; heavy wind 1–2 holes back.
Mast bend check
Hoist a coloured string on the main halyard and hold it at deck level to see that the mast bends evenly.
Downwind
Crew weight as far forward as possible.
Balance
Keep the boat as light on the rudder as possible.
  • A slide deck rather than a formal guide; the tuning text repeats the aluminium-mast guide with extra photos and notes.
  • Kicker threshold 16 kn here vs 18 kn on North's web guide; heavy-wind jib lead 'one or two holes back' here vs 'two holes' on the web guide.
  • Hosted on the Finnish Folkboat association's (folkkariliitto) website.

Folkboat Association (UK) – Cy Grysely — Nordic Folk Boat Base Settings Scanned PDF created 1 April 2023; by Cy Grysely with Ed Donald, based on measurements of Danish boats in 2022

Written for
Not stated
Tension gauge
A rig tension gauge reading in kg; make and model not stated
How it’s measured
Forestay: 131 cm from the bottom of the mast band to the deck (same as earlier guides). Mast position measured from the mast base to the forward face of the companionway bulkhead instead of from the transom. Forestay sag checked with a thin line from the jib tack to the spinnaker halyard carrying a rigid 8 cm marker at the 5th jib hank, set up in Force 1–3.
Source
Folkboat Association (UK) – Cy Grysely, Scanned PDF created 1 April 2023; by Cy Grysely with Ed Donald, based on measurements of Danish boats in 2022

Base setup

Forestay
131 cm; the fastest Danish boats measured 129–131 cm, most 131 cm
Forestay sag
8 cm, adjusted with the shrouds; in 14/18 kn upwind the mainsheet controls it, in light air use backstay to hold the 8 cm
Mast base
196 cm from the mast base to the forward face of the companionway bulkhead (the author's boat started at 198 cm; Danish boats 193–196 cm, nearly all 195/196 cm)
Mast base effect
Moving the base back 10, 20 or 30 mm moves the masthead roughly 100–140 mm
Shrouds
With the forestay at 131 cm, pull the backstay until the gauge reads 10 kg, then set the shrouds to 20/22 kg (most Danish boats 22 kg). Release the backstay and note the shroud reading as your base setting.
Shroud turns
About one turn off for very light air; one to two turns on for heavier conditions
Jumpers
Usually off in light air; in medium air one or two turns on (wooden rig); let off again in heavy air so the top falls away
Jib car
264–265 cm from the forestay buckle to the jib cars, depending on sails; 58 cm from centreline to the centre of the car as the base (less slot in light air, more in heavy)

Trim by condition

Backstay
Used a lot in light and heavy air, less in medium; the aim is to keep 8 cm of forestay sag in all conditions. Release it at the windward mark so the rig can go forward downwind.
Heavy air
Depower with backstay (twist in the top of the main) and/or more vang (flatter lower main); tighter shrouds firm the forestay and depower both sails.
Loose shrouds
The light shroud loads put the power in the lower main, where heeling moment is smallest, and let the boom go further out downwind; lock and tape the turnbuckle nuts.
  • Image-only scan; values read from the page images. The author's name is not printed in the document; it comes from the association's link ('by Cy Grysely'), and other association documents spell it Grisley.
  • Written for the UK fleet from observations of Danish boats; the author describes himself as a club sailor, and the figures come from his and Ed Donald's boats (Gybe n' and Madelaine).
  • Ed Donald's article 'The Best Things in Life are Free!' (Folk Boat Year Book 2022, pp. 43–46, folkboats.com) gives a related setup for Madelaine: 131–131.5 cm forestay mark and 8 cm sag; mid-weather (F3–4) mast step 4th hole back from the forward end of the step plate with shrouds at '4.3 on turnbuckles or 70 lbs on the luge gauge' (gauge as printed); light air 5th hole back and two turns off; heavy weather 3rd hole back and two to three turns on.
  • Tension values are in kg on an unnamed gauge; do not compare with Loos or other gauge readings without calibration.

North Sails — Nordisk Folkebåd tuning-guide til træmast (Nordic Folkboat tuning guide for wooden masts) Undated blog guide (Søren Kæstel, Per Jørgensen, Theis Palm); in Danish

Written for
North Folkboat mainsail and jib
Tension gauge
Not used
How it’s measured
Same forestay-mark rake method as the aluminium guide. Wooden-mast stiffness is graded by deflection: 10.5–14.5 cm with 16 kg hung 4.8 m from the top. Wind given in m/s.
Source
North Sails, Undated blog guide (Søren Kæstel, Per Jørgensen, Theis Palm); in Danish

Base setup

Mast stiffness
Deflection 10.5–14.5 cm, measured with 16 kg at 4.8 m from the top
Mast rake
Forestay mark 1.31 m from the deck along the forestay
Mast foot
Stiff mast: hard on the aft edge of the mast hole, pushed 22 mm aft; about 12.5 cm deflection: 16 mm; soft mast (14.5 cm): just touching the aft edge
Soft masts
Use a 2 cm wedge on the aft edge of the mast hole to get the same effect on forestay tension
Jumpers
Adjusted with the backstay pulled hard; fairly loose in light wind, tighten the common turnbuckle 2–3 turns in medium wind (mellemluft). Aim for an even bend from deck to top.
Forestay sag
About 8 cm in light wind; shrouds +1½ turns in medium, +1½ more in fresh wind
Jib lead reference
2.65 m from the forestay fitting to the centre of the sheet block (cabin-top sheeting)

Mainsail controls by wind (m/s)

ControlLightMediumStrong
Outhaul0–2 m/s: 3 cm from the black mark2–5 m/s: 1.5 cm from the markOver 5 m/s: out to the mark
CunninghamOffJust remove luff wrinklesOver 7 m/s: pull hard
Traveller0–3 m/s: 15–20 cm to windward3–6 m/s: centredCars to leeward until light on the helm

Trim by condition

Mainsheet
As in the aluminium guide; top batten parallel to the boom in almost all winds.
Backstay
Marked every 20 cm.
Kicker
Never upwind below 8 m/s; ease before bearing away; off the wind set so the top batten is parallel to the boom.
Jib sheet
Middle batten parallel to centreline; 0–2 m/s 2–3° more twist; in a lot of chop 2–3 holes forward; strong wind 1–2 holes back without the lower leech going slack.
Jib halyard
Never pull it too hard (the draft moves forward); in light air small creases at the hanks are fine.
  • Unlike the aluminium guide, the mast foot setting here depends on mast stiffness only, not on wind strength.
  • The Danish jumper text says loose in light wind and 2–3 turns in medium wind but does not clearly say what to do in strong wind; the aluminium guide returns them to fairly loose.
  • Translated from Danish ('sidevanter' = shrouds, 'forstag' = forestay, 'hækstag' = backstay); all wind speeds are in m/s.

Doyle Raudaschl — Nordisches Folkeboot – Trimmbeschreibung (trim description) Undated (PDF uploaded July 2021); by Gunter May, with experience from Walter Muhs and Christoph Nielsen; in German

Written for
Doyle Raudaschl A 26 (KSR allround) and A 27 (KSR light-wind) main and jib
Tension gauge
Not used – shroud and forestay lengths measured from a mark
How it’s measured
Rake is measured differently from North: hang a weight on the main halyard as a plumb line and measure along the top of the boom (set at the measurement band) from the aft face of the mast to the plumb line, with only racing gear aboard, ideally in no wind. All figures are from the author's own 1987 Folkebootzentrale-built boat.
Source
Doyle Raudaschl, Undated (PDF uploaded July 2021); by Gunter May, with experience from Walter Muhs and Christoph Nielsen; in German

Base setup

Mast rake (plumb line)
Coastal: 60–65 cm aft. Inland / lighter winds: about 40–55 cm with generally looser shrouds; the author sails with about 56 cm. A more upright mast with looser shrouds helps a lot downwind. Rake is set by the forestay alone, so keep it loaded with light backstay or shroud tension while measuring.
Mast at deck
Always firmly against the aft edge of the mast hole so the bend continues down into the boat
Mast position
495 cm from the aft edge of the transom to the aft edge of the mast foot (tape run over the traveller beam and aft deck); 196,5 cm from the mast foot to the inside of the cabin bulkhead (Folkebootzentrale hulls only)
Prebend
After setting rake, move the mast 1–2 holes aft in the mast shoe (shrouds briefly very loose); don't then tighten the forestay – mainsheet and shrouds load it when sailing
Forestay (light-wind setting)
Take the forestay up to the mast measurement band and mark it at the band's lower edge; reattached, the mark is 126 cm from the forestay pin centre
Shrouds (light-wind setting)
Same method: lower edge of the measurement mark to the inner chainplate seat 111 cm
Centring
Either equal distance mast-to-side-deck both sides, or a steel tape on the main halyard to each chainplate (the author's preference, in calm conditions)
Jib H-track
Fit on the cabin top; its midpoint (from the jib's lead-line mark) is the medium-wind lead

Settings by wind (Beaufort)

ControlLight 1–2 BftMedium 3–4 BftHeavy 5+ Bft
ShroudsLight-wind setting (111 cm mark)+1–2 turns both sidesA further +1–2 turns
MainA 26 or A 27A 26 or A 27A 26 only
TravellerUp to 20 cm to windwardCentredCentred to about 10–30 cm to leeward, by helm
CunninghamLoose, ignore wrinklesLoose to slight tensionTension by mast bend; perhaps just remove luff wrinkles
OuthaulSlight tension, no crease along the footTightTo the mark
Mainsheet / backstaySheet fairly loose, check twist (top batten never to windward); backstay loose or lightSheet tight, twist via sheet and/or backstay; backstay otherwise looseEither traveller eased a hand's width with soft sheet and firm backstay, or traveller well down with firm sheet and loose backstay
JibA 27 light or A 26A 26 or A 27A 26 only
Jib lead fore-aftA 27 in 4–7 m/s: 259 cm from forestay pin to blockMidpoint of the H-track2–3 holes aft of the midpoint
Jib lead athwartshipsAbout 48–50 cm from centreline2 holes out, about 50–52 cmAbout 2 holes out, about 52 cm
Jib luff / sheetLuff very slight (small wrinkles at the hanks); sheet loose, round sailSheet harderLuff firmer; sheet hard

Trim by condition

Jumpers
Depend on mast stiffness: ideally fairly loose with an even bend into the deck; on stiffer masts tighten them to avoid a 'walking-stick' bend that only starts above the hounds, and add bend low down with backstay. Always tighten both sides equally; adjustable jumpers can be pulled hard downwind to stop the head falling to leeward.
Forestay logic
Loose shrouds and sheets give a loose forestay and a full jib; tight shrouds and sheets a tight forestay and a flat jib.
Kicker
Never used upwind in any wind. Downwind light/medium: just enough to keep the sail about 1 cm off the jumper ends; heavy: firm.
Downwind
Backstay fully off (light pull in rough sea when windy), outhaul eased (heavy: until the foot crease disappears), boom against the shroud; at 6–7 Bft sheet slightly harder so the sail doesn't wrap the jumper. Jib goosewinged square with a shortened pole or a shorter pole of about 290 cm.
Balance
Use mainsheet, traveller, backstay and cunningham together to keep the helm near neutral at maximum pointing.
  • The guide's light-wind section is 1–2 Bft, but its A 27 jib lead figure is given for 4–7 m/s.
  • Rake (plumb-line along the boom) is not comparable with North's 1.31 m forestay-mark method.
  • Measurements (mast position, forestay and shroud marks) are for the author's own boat; transfer with care.
  • Translated from German: Wanten = shrouds (one pair; no separate lowers), Vorstag = forestay, Achterstag = backstay, Mastfall = rake, Lot = plumb line, Mastschuh = mast step, Jumpstagen = jumpers, Baumniederholer = kicker, Unterliek = foot/outhaul, Holepunkt = jib lead, Windstärken = Beaufort.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Nordic Folkboat resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Nordic Folkboat by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
We have no current one-design class rules on file for the Nordic Folkboat. Racing legality depends on your class or handicap rules; check them before changing equipment.