One-design race shop · Dinghy
Snipe Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Snipe
All Snipe equipment
29 parts
Fit verified for Snipe
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for Snipe
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for Snipe
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for Snipe
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Snipe
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Snipe
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Snipe
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Snipe
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Snipe
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for Snipe
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Snipe
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for Snipe
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Snipe
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Snipe
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Snipe
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Snipe
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Snipe
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for Snipe
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No Snipe parts match these filters.
Can’t find a part for your Snipe? Request a Snipe part
Official Harken dealer
Snipe deck layout
- LOA
- 15 ft 6 in (4.7 m)
- LWL
- 13 ft 6 in (4.1 m)
- Beam
- 5 ft (1.5 m)
- Sail Area
- 128 sq ft (11.8 sq m)
- Weight
- 381 lb (173 kg)
Deck layout
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Snipe tuning guide
Snipe tuning revolves around spreader length and tip-to-tip angle, rake measured from the masthead to the top of the transom, shroud tension on a Loos PT-1 gauge and pre-bend set by the jib halyard, then a fore-and-aft puller at the deck. Guides differ by mast (Proctor, Sidewinder, Persson, Cobra), hull builder (rake numbers shift by about 1" between builders) and style (Quantum publishes separate San Diego and Brazil grids), so match the guide to your sails, mast and hull.
North Sails — Snipe Tuning Guide and CB-2 / R3-LM Tuning Matrix Undated web guide; matrix images uploaded April 2025 (CDN timestamp)
- Written for
- CB-2 main and R3-LM jib
- Tension gauge
- Loos PT-1 (named in the matrix; the web text names no gauge)
- How it’s measured
- Rake: 25 ft tape on the main halyard, pulled to the top and locked, measured to the top of the transom (numbers based on the Persson deck crown). Spreader length from the side of the mast to the shroud/spreader intersection; tip-to-tip shroud to shroud with spreaders fully back. Mast deck marks: neutral, then 3/8", ¾" and 1" forward of neutral (and 3/8" aft for Sidewinder Jr.).
- Source
- North Sails, Undated web guide; matrix images uploaded April 2025 (CDN timestamp)
Base setup
- Mast butt
- 60" behind the stem (matrix)
- Shroud attachment
- Forward hole, 70" aft of the stem (maximum forward)
- Jib tack
- 11" back from the stem (maximum forward); forestay shock cord 15" up the forestay
- Spreaders (web text)
- 16¾" (42.5 cm) start; tip-to-tip 29¼" (74 cm), 29¾" (76 cm) for heavy air or heavier crews
- Spreaders (matrix)
- 16.5"–16.7" long; tip-to-tip 29.8" (30" when overpowered)
- Shroud adjusters
- Holt Allen staggered-hole or Sta-Master style
- Crew weight
- 275–325 lb competitive
- Masts (stiffest to softest)
- Sidewinder Gold, Sidewinder, Proctor, Persson
CB-2 and R3-LM tuning matrix (imperial; shroud tension on Loos PT-1)
| Setting | Seeking power | Fully hiked | Becoming overpowered | Overpowered (15–18 kn) | Overpowered (18+ kn) |
|---|---|---|---|---|---|
| Shroud position | Forward hole | Forward hole | Forward hole | 2nd hole from front | 3rd hole from front |
| Shroud turns | Base | Base +1 | Base +2 | Base +3 | Base +4 |
| Shroud tension (PT-1) | 19 | 21 | 23 | 24 | 25 |
| Mast at deck | ½" forward | Neutral | ½" forward | 1" forward | 1.25" forward |
| Spreader tip to tip | 29.8" | 29.8" | 29.8" | 30" | 30" |
| Prebend | 2" | 2.5" | 2.5" | 2.5" | 2.5" |
| Rake | 21′7.25″ | 21′6.5″ | 21′6″ | 21′5.5″ | 21′4.5″ |
| Vang | Slack out | Slack out | Slack out | Vang sheet | Vang sheet |
| Traveller | Centred | Centred | Down 2" | Down 4" | Down 6" |
| Outhaul | Light ease | Max | Max | Max | Max |
| Cunningham | Horizontal wrinkles | Slight wrinkles | Almost smooth | Smooth | Smooth |
| Tack line length | 2" from mast | 2" from mast | 1.75" | 1.5" | 1" |
| Jib cunningham | Hint of wrinkles | Hint of wrinkles | Smooth | Tighter | Max |
| Jib lead | Trim line extension | Trim line extension | Trim line extension | Trim line extension | Trim line extension |
| Jib height at tack | 2" above deck | 2" above deck | 2" above deck | 2.5" above deck | 2.5" above deck |
| Jib leech vs spreader tip | ½" inboard unless really light | At spreader tip | ½" outboard | 1" outboard | 2–3" outboard |
Trim by condition
- Mainsheet
- Under 7 kn the top telltale flies about 70% of the time; above 7–10 kn it should fly all the time.
- Outhaul
- Tight upwind; ease 2–3" downwind.
- Vang
- Slack until hiking hard; pull the mast to the aft mark as the breeze builds.
- Puller
- Light air with crew inside: forward deck mark. Crew to windward: neutral. 15+ kn: aft mark on soft masts, forward to neutral on stiff masts.
- Traveller
- Centred in most conditions; drop it when overpowered.
- Main tack line
- Sail edge about 3/8" aft of the back of the mast (web text).
- Jib
- Start with the sheet in line with the trim stripe on the clew; leech telltale a third of the way down; reference mark on the splash rail 15" from centreline. Jib halyard needs at least 10–12" of throw: tighten a third to a half for reaching with the pole up; fully off dead downwind.
- The web text and the matrix give slightly different spreader numbers (16¾" / 29¼" vs 16.5–16.7" / 29.8"); the matrix is the newer, sail-specific setting.
- A metric version of the matrix is also published: https://cdn.shopify.com/s/files/1/0688/6549/1220/files/2Snipe_CB-2_Matrix_Metric.jpg
- The web page says to download a PDF chart, but only the matrix images are linked.
Quantum Sails — Snipe Tuning Guide and Snipe Tuning Grid (San Diego and Brazil styles) 2020 (grid dated July 2020)
- Written for
- Quantum Snipe main and jib (models not named)
- Tension gauge
- Loos PT-1
- How it’s measured
- Tape on the main halyard locked at the top (head of the main level with the bottom of the top band), measured to the top of the transom. Guide: spreader length from the side of the mast to the shroud/spreader intersection, measured on top of the spreader at the shortest distance; grid: centre of shroud to closest point on mast or bracket, tips fully aft. A Persson measures 1.75" (4.5 cm) from a transom-corner straight edge to the deck: add or subtract the difference to your rake number. Grid: https://quantumsails.com/en/sails/one-design/documents/snipe/snipe-tuning-grid-2020.aspx
- Source
- Quantum Sails, 2020 (grid dated July 2020)
Base setup
- Spreader length
- 16½"–16⅞" (42–43 cm) quick setup; prescribed range 15⅞"–16¾" (40–42.5 cm)
- Spreader angle (tip to tip)
- 29"–30½" (73.5–77.3 cm in the quick setup; 73.6–77.5 cm in the text), spreaders locked aft
- Rake (jib halyard final)
- 21′5"–21′7" (652–658 cm) quick setup; 21′6"–21′7" (653–658 cm) in the setup steps
- Builder correction
- Figures for McLaughlin, Persson, Eclipse or Jibe Tec; add 1" for Phoenix, Lillia or Mueller; subtract ¾" (2 cm) for Skipper
- Pre-bend / tension
- 1½–2½" (38–63 mm) pre-bend at 21 on PT-1 (base 20–21); if the mast is too stiff, use 19
- Shroud attachment
- 5′5¾"–5′6¼" from forestay pin to shroud pin (167 cm from the front hole on a Persson with shrouds 4′7½" / 141 cm apart; about 5′7" / 170 cm aft if 4′9" / 145 cm apart)
- Mast butt
- Persson: centre of transom to pin 10′8⅞" (327.4 cm) [2020 grid: 10′9", #3, 39 cm pin to front of trunk]; Jibetech: centre of transom indent to pin 10′8⅛" (325.5 cm) [grid: or 9.5–9.75" from tube to pin]. Typically ¾–1" gap in front of the mast at the partner.
- Jib tack
- 11" (27.9 cm) aft of the stem
- Mast quick set
- Proctor: rake 21′6" (655 cm), spreaders 16⅞" x 29¾", tension 21–22 (printed with inch marks). Sidewinder & Cobra II: rake 21′6", spreaders 16¾"–16.5" x 29.5", tension 21–22. Sidewinder Junior: 15⅞" x 30½" with 1" pre-bend.
- Deck marks
- Neutral (pre-bend) mark, plus marks ¾" (1.9 cm) in front and ½" (1.3 cm) behind
- Jib lead spacing
- 27"–32" (68.5–81.3 cm) between lead bearing surfaces; newer boats about 2′5.5" (75 cm)
- Grid assumptions
- Main halyard locked: 16′9" to the top of the black band (at gooseneck); shrouds 5′6" from bow, 4′7.5" apart; jib halyard has 12 of throw for the run (printed 12′, presumably inches); add 1 unit of tension with 1/8" 1x19 wire
- Spreaders (San Diego grid, by crew weight, not wind)
- Range 16½–16⅞ long, 28.75/30.5 tip to tip; light team 16.5 x 28.75; 305 lb team 16.75 x 30; heavy team 16.75 x 30.25
Tuning grid 2020, San Diego style (shroud tension on Loos PT-1)
| Wind (kn) | 4–6 | 7–9 | 10–15 | 16–22 | 22+ |
|---|---|---|---|---|---|
| Crew | Leeward | Weather side | Hiking | Full hiking | Full hiking |
| Turns | 1 | 0 | 1 | 3 | 4 |
| Final rake | 21′6.5″ / 7″ | 21′7″ | 21′6.5″ | 21′4″ | 21′3.5″ |
| Shroud tension | 19 | 18 | 19 | 22 | 23 |
| Pre-bend | 60 mm | 50 mm | — | — | Ease halyard slightly |
| Shroud position | 1 | 1.5 | 2 | 2 | 2–3 |
| Puller | ¾" forward | .25" forward | .25" aft | Neutral | Neutral |
| Outhaul | Off 1.25" | Off ¾" | On to band | Foot tight | Foot tight |
| Leeward shroud | Tight | Just loose | 15° | — | — |
| Traveller | 0 | — | 3–6" | 8 | 10 |
| Cunningham | Add ½" | — | Draft under 2nd number from front | Hard | Skipper and crew both pull |
Tuning grid 2020, Brazil style (metric; shroud tension on Loos PT-1)
| Wind (kn) | 4–7 | 8–11 | 12–15 | 16–19 | 20+ |
|---|---|---|---|---|---|
| Crew | Leeward | Weather side | Hiking | Full hiking | Full hiking |
| Turns | 1 | 0 | 1 | 1 | 2 |
| Final rake (m) | 6.53 | 6.54 | 6.5 | 6.5 | 6.47 |
| Shroud tension | 24 | 21 | 21 | 21 | 21 |
| Pre-bend | Ease halyard | — | — | — | — |
| Spreader length (cm) | 42 | 42 | 42 | 42 | 42 |
| Tip to tip (cm) | 73 | 73 | 76 | 78 | 78 |
| Shroud position | 1 | 1 | 1 | 1 | 1 |
| Puller | Forward 2 cm | Neutral | Neutral | Forward 1 cm | Aft 1.5 cm |
| Outhaul | Off 1.25" | Off ¾" | Tight | Foot tight | Foot tight |
| Leeward shroud | Tight | Tight | Loose | Loose | Loose |
| Cunningham | Add ½" | Slight | Draft under 2nd number from front | Hard | Hard |
Trim by condition
- Power vs depower
- For power, make the mast more upright and/or the shrouds looser; to depower, rake back and/or tighten the shrouds. Average crew is defined as 300 lb.
- Pre-bend check
- Mast floating in the partners, jib wire tensioned: hold the main halyard against the back of the spreader bracket; at the top of the black band it should be within ¼" of the front of the mast. Too much: ease shrouds; too little: tighten, then re-measure rake.
- Stepping up (US tuning)
- For 15–18 kn, tighten shrouds half a hole (Holt-Allen) or 1.5 turns (Sta-Master) keeping the same jib halyard mark; over 15–18 kn, move the shrouds aft one hole (¾", 2 cm). Use the same halyard mark for every setting.
- When to tighten
- If the leeward Sta-Master leans more than about 20°, or more than three finger-widths of sag between jibstay and forestay at the bottom telltale, tighten the shrouds.
- Spreader symmetry
- Pull the jib halyard hard with the puller off, stand about 20′ to the side and check the shrouds line up as one; adjust the screws until they do.
- Mast partner
- Shim tight with the rig loaded; pull the mast ½" (15 mm) aft at the deck to straighten it, then sight up the back to check.
- Jib halyard
- Needs at least 10" of ease from the rake setting to square the pole aft on the run.
- The guide's rake ranges differ slightly between the quick-setup table (21′5″–21′7″) and the step-by-step (21′6″–21′7″).
- In the San Diego grid the spreader sizes are given by crew weight (light / 305 lb / heavy team), not by wind band, so they are listed under base settings rather than in the wind table.
- The grid's '305 pounds' spreader setting is 16.75 x 30 (2020) versus 16.75 x 30.25 in the 2015 grid.
- The San Diego grid's 22+ pre-bend cell is printed 'Easy halyard slightly' (read as ease).
Quantum Sails — Quantum Sails Snipe Tuning Grid (C-5) 15 December 2015
- Written for
- Quantum C-5 main
- Tension gauge
- Loos PT-1
- How it’s measured
- Same base assumptions as the 2020 grid; jib halyard stays at the same mark through the wind range.
- Source
- Quantum Sails, 15 December 2015
Base setup
- Mast step
- Persson: centre of transom to centre of pin 10′8⅞" or forward (38.39–40 cm pin to front of trunk); Jibetech: 10′8⅛" from the transom indent
- Main halyard check
- 16′9" from the locked halyard to the top of the black band
- Initial rake
- 21′2"
- Spreaders
- 16½–16⅞ long, tip to tip 28.75/30.5; light team 16.5 x 28.75; 305 lb team 16.75 x 30.25; heavy team 16.75 x 30.75
C-5 grid by wind (Loos PT-1)
| Wind (kn) | Final rake | Shroud tension | Shroud position | Aft puller | Outhaul | Traveller | Cunningham |
|---|---|---|---|---|---|---|---|
| 4–6 | 21′7″ | 17/18 | 1.5 | ⅛" forward | Ease 1" | 0 | — |
| 7–9 flat water | 21′6.75″ | 19 | 1.5 | Float | Ease 1" | 0 | — |
| 7–9 waves | 21′6.25″ | 20 | 1.5 | Float | Ease ¼" | 0 | — |
| 10–15 | 21′5.5″ | 21 | 1.5 | .25" aft | To band | 3–6" | Crease from clew to cunningham grommet |
| 16–22 | 21′4.5″ | 22 | 1.5 | Neutral | To band | 8 | Draft under 2nd number from front |
| 22+ | 21′3.5″ | 23 | 1.5 | Neutral | To band | 10 | — |
Floating jib lead
| Wind (kn) | Forestay to twing-line distance | Twing-line ease | Distance between twings | Jib sheet vs cockpit edge |
|---|---|---|---|---|
| 5–10 | 90" | 0–1" ease | 29" | Even |
| 12–18 | 89" | 2" ease | 31" | 1–2" out |
| 18+ | 88" | 3" ease | 33" | 3′–4" out (as printed) |
- Older Quantum grid for the C-5 main; superseded by the 2020 grid.
- Jib-lead headings as printed: forestay to twing-line, twing-line eased from car, distance between twings pulled apart, jib sheet in/out compared to cockpit edge.
- The traveller figures 8 and 10 carry no units in the grid.
Quantum Sails — Snipe Tuning Guide (Quantum Snipe Performance Guide) with Tuning Grid 2009 (PDF created October 2009; Quantum San Diego: George Szabo, Mark Reynolds, Eric Heim)
- Written for
- Quantum SD-6K and C-2 mains (separate grids)
- Tension gauge
- Loos PT-1 (quick setup also quotes 180–220 lb)
- How it’s measured
- Grid base assumptions: Persson mast step centre of transom to pin 10′8⅞", Jibetech 10′8⅛" from the transom indent; spreaders measured on top, tips aft, centre of shroud to closest point on mast or bracket; jib halyard kept at the same mark through the wind range; 16′9" from the locked main halyard to the top of the black band.
- Source
- Quantum Sails, 2009 (PDF created October 2009; Quantum San Diego: George Szabo, Mark Reynolds, Eric Heim)
Base setup
- Spreaders
- 16.5"–16⅞" (42–43 cm) long; angle 29"–30½" (73.5–77.3 cm) tip to tip
- Initial shrouds (rake before jib)
- 21′1"–21′2" (642–645 cm)
- Jib halyard (final rake)
- 21′5"–21′7" (652–658 cm)
- Pre-bend / tension
- 1½–2½" pre-bend (printed as 28–50 mm); 180–220 lb on a Loos gauge; base 18–19 on the PT-1
- Shroud deck location
- 5′5.75"–5′6.25" from forestay/jibstay pin to shroud pin
- Jib tack
- 11" (27.9 cm) aft of the stem
- Starting settings
- Proctor: rake 21′6½", spreaders 16⅞" x 29¾", tension 18–19. Sidewinder & Cobra II: rake 21′6½", spreaders 16¾" x 29.5", tension 18–19.
- Builder correction
- Rake figures for McLaughlin, Persson, Eclipse or Jibe Tec; add 1" for Phoenix, Lillia or Mueller; subtract 2 cm (¾") for Skipper
SD-6K grid (shroud tension on Loos PT-1; initial rake 21′2")
| Wind (kn) | Final rake | Shroud tension | Tip to tip | Shroud position | Aft puller | Outhaul | Traveller | Cunningham |
|---|---|---|---|---|---|---|---|---|
| 0–6 | 21′7" | Less 1 turn | 29 | 1 | 1" forward | Ease 3/4" | 0 | Slight wrinkles |
| 7–9 flat water | 21′6.5" | Base 18–19 | 29 | 1 | Neutral | Ease 1/2" | 0 | — |
| 7–9 waves | 21′6.5" | Base 18–19 | 29.5 | 1 | Neutral | Ease 1/2" | 0 | — |
| 10–15 | 21′6" | Add 1 turn | 29.5 | 1 | Neutral | To band | 2–4" | Some wrinkles from cunningham grommet |
| 16–22 | 21′5.5" | Add 2 turns | 29.5 | 1 | Neutral | To band | 4–8" | Draft under 2nd number from front |
| 22+ | 21′5" | Add 2 turns | 29.5 | 1 | Neutral | Ease 1/4" | 10+" | — |
C-2 grid (shroud tension on Loos PT-1; initial rake 21′2")
| Wind (kn) | Final rake | Shroud tension | Tip to tip | Shroud position | Aft puller | Outhaul | Traveller | Cunningham |
|---|---|---|---|---|---|---|---|---|
| 0–6 | 21′7" | Less 1 turn: 16–17 | 29 | 1 | 1" forward | Ease 1/2" | 0 | — |
| 7–9 flat water | 21′6.5" | Base 18–19 | 29 | 1 | Float | To band | 0 | — |
| 7–9 waves | 21′6.5" | Base 18–19 | 29.5 | 1 | Float | Ease 1/4" | 0 | — |
| 10–15 | 21′6" | Add 1 turn: 20–21 | 29.5 | 1 | .25" forward | To band | 2–4" | Crease from clew to cunningham grommet |
| 16–22 | 21′5.5" | Add 2 turns: 22–23 | 29.5 | 1 | .5–.75" forward | To band | 8 | Draft under 2nd number from front |
| 22+ | 21′5" | Add 3 turns: 24–25 | 29.5 | 1 | .5–.75" forward | To band | 10 | — |
Floating jib lead
| Wind (kn) | Forestay to twing-line | Twing-line eased from car | Distance between twings | Jib sheet vs cockpit edge |
|---|---|---|---|---|
| 5–10 | 90" | 0–1" ease | 29" | Even |
| 12–18 | 89" | 2" ease | 31" | 1–2" out |
| 18+ | 88" | 3" ease | 33" | 3′–4" out (as printed) |
- Older Quantum edition (2009) for SD-6K and C-2 mains; superseded by the 2020 guide. Spreader length in both grids is 16¾–16⅞" (given in the 0–6 row).
- The quick-setup pre-bend conversion (1½–2½" = 28–50 mm) is as printed and does not match the inch figures; the 2020 guide prints 38–63 mm.
- Traveller figures 8 and 10 in the C-2 grid carry no units.
Sailboats (sailboats.co.uk) — Snipe Tuning Guide by Sailboats Undated web article
- Written for
- North Snipe main and jib
- Tension gauge
- PT-1 (units not stated)
- How it’s measured
- 25′ tape on the main halyard to the top of the transom.
- Source
- Sailboats (sailboats.co.uk), Undated web article
Base setup
- Spreader length
- 16¾" (42.5 cm), side of mast to shroud/spreader intersection
- Tip to tip
- 30 11/16" (78 cm) start; 31½" (80 cm) heavy air/heavier crews; 29 15/16" (76 cm) very light air
- Mast heel
- 60" aft of the stem
- Shroud attachment
- 70" aft of the stem (move back slightly if lacking power)
- Jib tack
- 11" back from the stem; forestay shock cord 15" up
- Masts
- Cobra II, Sidewinder Sr., Proctor Miracle, Sidewinder Junior
Rake and tension (PT-1)
| Wind (kn) | Mast rake | Tension (PT-1) |
|---|---|---|
| 0–8 | 21′7″ | 18 |
| 9–15 | 21′5″ | 20 |
| 15–22 | 21′4″ | 22 |
Trim by condition
- Puller
- Light air (crew inside): forward mark, ¼" ahead of neutral. Crew to windward: neutral. 15+ kn: softer masts at the aft mark ¼" behind neutral (Sidewinder Junior 3/8"); stiffer masts let forward to neutral.
- Main
- Tack edge about 3/8" aft of the back of the mast; top telltale flying about 70% of the time under 7 kn, constantly above 7–10 kn; outhaul tight upwind, eased 2–3" downwind.
- Jib
- Halyard throw at least 10–12"; tighten a third to a half when reaching with the pole; fully off dead downwind. Splash-rail marks 15" from centreline.
- Published by a UK chandlery for North sails; it reads like an older edition of North's guide (different tip-to-tip numbers from North's current matrix).
- The Speed Sails PDF linked from class resource pages (sailboats.co.uk/media/datasheets/snipe_tuning_ guide.pdf) now returns 404.
Snipe Fleet #001 (Dallas) — Snipe Fleet #001 Tuning and Racing Guide (2024 Edition) 2024 edition (file named 2025)
- Written for
- Not sail-specific (nominal settings for newer sailors)
- Tension gauge
- Loos (model not stated)
- How it’s measured
- 25 ft tape attached at the top of the main halyard shackle clevis pin, measured to the top of the transom (beside any rudder cut-out). Wind ranges are in mph.
- Source
- Snipe Fleet #001 (Dallas), 2024 edition (file named 2025)
Base setup
- Spreader length
- 16¾", side of mast to shroud where it passes through the spreader
- Spreader tip to tip
- 30¾"; some use 29½" (lighter crews, under 300 lb combined, lean shorter)
- Mast at deck
- 59"–60" from the stem (59" is the class minimum)
- Initial rake
- 21′1" (20′11"–21′3" fine), before sails
- 10–15 mph setting
- Sta-Masters in the first hole aft from the front; jib halyard to 20 on the Loos; rake 21′5½" to the centre of the transom
- Pre-bend
- 1–1.25" between sail track and tape at the spreaders
- Jib fairleads
- Block 88" from the jib stay clevis pin at 7–17 mph; 1" aft at 0–7 and over 17 mph; outboard up to 2" over 15 mph
- Splash rail mark
- 16" from the centre of the mast
Rake, Loos tension, shroud hole and traveller by wind (mph)
| Wind (mph) | Mast rake | Loos gauge | Shroud attach | Traveller |
|---|---|---|---|---|
| 5–10 | 21′6½″ | 18 | First hole | None |
| 10–15 | 21′5½″ | 20 | First hole | None |
| 15–20 | 21′4½″ | 22 | Second hole | 3"–6" |
| >20 | 21′4″ | 22 | Second hole | 6"–12" |
Trim by condition
- Shrouds
- Normally the foremost hole; move back one in medium to heavy air (also guards against the mast inverting on runs). Adjust only between races.
- Marks
- Write the Sta-Master setting for each wind range on the jib; mark the jib-halyard hook position on the mast for each range.
- A fleet guide for beginners and intermediates; it recommends sailmaker-specific settings for advanced sailors.
- Fractions and table checked against the rendered PDF pages (the PDF text layer drops the fraction glyphs).
Luis Soubié (Snipe Class / SnipeToday) — How to Improve Fast – 3. How to Set-Up the Rig 25 January 2015
- Written for
- Not sail-specific; Persson hull, Sidewinder Gold mast, 1/8" wire shrouds (not Dyform); crew 130–140 kg (286–308 lb)
- Tension gauge
- Tension gauge readings quoted as silver / black scale (brand not stated)
- How it’s measured
- Rake: masthead to transom. Pre-bend: tape held at the gooseneck, gap at spreader height. Spreader opening between the shrouds with spreaders against the stops.
- Source
- Luis Soubié (Snipe Class / SnipeToday), 25 January 2015
Base setup
- Spreader length
- 42.5 cm (16¾"); heavier crews add 1–2 cm
- Spreader opening
- 75–77 cm (29½"–30¼"); flat main or soft mast 78 or 80 cm
- Rake
- 6.55–6.57 m (21′6"–21′6.5")
- Shroud tension (base)
- 27 silver / 21 black; 25 silver / 19 black is easier to sail
- Pre-bend
- About 3–4 cm
- Mast gap at partners
- 1–1.5 cm forward; more than 1.5 cm: move the bolt forward (old Persson: one hole ahead of the 60" position)
Shroud steps by wind
| Step | Shroud setting | Wind |
|---|---|---|
| 1 (base) | Mast locked at the deck mark | 0 to about 10–12 kn |
| 2 | Half a hole tighter than step 1 | Over 10 kn to about 15 kn |
| 3 | Another half hole | When the main must be eased constantly |
| 4 | One more half hole | Over 20 kn |
Trim by condition
- Light air
- Under 7 kn with a hard leech, pre-bend the mast forward to the maximum.
- Cunningham
- Loose with small wrinkles until step 3, a little on at step 3, full on at step 4.
- Jib halyard
- Ease 1–2 cm when tired above 20 kn.
- Written by a top Snipe sailor for the class website; not tied to one sailmaker.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Snipe resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Snipe by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Snipe class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rules2026 Class Rules, effective 2026-01-15 (World Sailing, status Approved)
- Class associationsnipe.org
- Builder specificationsSnipe on jibetech.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Snipe part