One-design race shop · Dinghy
Escape Solsa 9 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Escape Solsa 9
All Escape Solsa 9 equipment
6 parts
Fit verified for Escape Solsa 9
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for Escape Solsa 9
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for Escape Solsa 9
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Escape Solsa 9
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Escape Solsa 9 parts match these filters.
Can’t find a part for your Escape Solsa 9? Request a Escape Solsa 9 part
Go fast
Escape Solsa 9 tuning guide
The Solsa is an unstayed sprit-rigged (Escape SimpleRig) beginner dinghy, so setup means downhaul and sprit tension and daggerboard use. The builder's owner manual is the only source and gives these settings by eye, not in numbers; Escape is no longer trading and the manual survives on an owner-run archive site.
Escape Sailboat Company — Escape Solsa manual – How to set up and sail your Escape SimpleRig boat Undated 4-page owner manual (PDF made May 2007 from a Word file)
- Written for
- Solsa SimpleRig mainsail (the manual does not describe the sail further)
- Tension gauge
- Not applicable
- How it’s measured
- All settings are by eye (wrinkles in the sail); the manual gives no measurements.
- Source
- Escape Sailboat Company, Undated 4-page owner manual (PDF made May 2007 from a Word file)
Base setup
- Mast
- Two-piece: top section slides over the bottom; step on the metal pin with the sprit facing forward, then rotate so the sprit points aft and the locking pin catches under the deckplate
- Downhaul
- Small pulley on the grommet (silver ring) at the tack; downhaul rope looped through it and fed through the mast eyestrap, tensioned until there is a slight vertical wrinkle in the sail
- Sprit
- 3-ft sprit rope: figure-8 knot, through the eye on the sprit, through the eyestrap on the mast, round the pulley and into the black V-cleat under the sprit; pull it tight to remove wrinkles in the sail – the mast bending under this tension is expected
- Clew
- Pulley on first, then the clew shackle, to the sprit end (tighten the shackle with pliers)
- Mainsheet
- Figure-8 knot through the eyestrap on the rudder bracket, through the sprit-end pulley, the loop and the pulley at the mast foot, then the optional cleat
Trim by condition
- Sail trim
- Use the Windicator on the bow and the matching colour-coded Sailtrimdex at the mast base: trim the sheet so the sail sits in the same colour zone the Windicator points to.
- Daggerboard
- Push it down gradually as the water gets deeper when leaving the beach.
- Slowing down
- Steer into the 'stop' zone or release the mainsheet.
- A builder's beginner manual; it has no numeric tuning settings. Escape no longer trades, and this copy is kept by an unaffiliated owner site.
- The setup and sailing pages are written for Escape 'SimpleRig' boats generally (the sailing page also mentions the Mambo); daggerboard and cockpit-plug items are marked 'Solsa model only'.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Escape Solsa 9 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Escape Solsa 9 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Escape Solsa 9. Racing legality depends on your class or handicap rules; check them before changing equipment.