One-design race shop · Keelboat
Rhodes 19 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Rhodes 19
All Rhodes 19 equipment
13 parts
Fit verified for Rhodes 19
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 100' long
Part # buc-cro-nal38100
$41.18
Fit verified for Rhodes 19
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 150' long
Part # buc-cro-nal38150
$70.70
Fit verified for Rhodes 19
Barton Marine
Barton Windicator WP285 – Offshore Racing
Part # bam-84004
$59.00
Fit verified for Rhodes 19
Ritchie
Ritchie X-11Y SportAbout Handheld Compass - Yellow
Part # rit-x-11y
$59.99
Fit verified for Rhodes 19
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Rhodes 19
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Rhodes 19 parts match these filters.
Can’t find a part for your Rhodes 19? Request a Rhodes 19 part
Go fast
Rhodes 19 tuning guide
The only published Rhodes 19 tuning guide is Doyle's: mast-step position, uppers and lowers in pounds on a Loos Model A gauge by wind, then outhaul, backstay and jib-luff settings by wind. Class sailors note the boats vary, so treat the numbers as a starting point and read tensions on the same gauge model.
Doyle Sails — Rhodes 19 Tuning Guide (Jud Smith and Tomas Hornos) PDF created June 2018 (Doyle One Design layout); text unchanged from Doyle's 2014 web page
- Written for
- Doyle Rhodes 19 main, jib and spinnaker
- Tension gauge
- Loos Tension Gauge, Model A (readings given in lbs)
- How it’s measured
- Mast step: tape from the intersection of the transom centre and the deck to the aft edge of the mast step. Centre the mast with the uppers, checking with a tape on the jib halyard to each chainplate; sight up the aft face of the mast to check it is straight.
- Source
- Doyle Sails, PDF created June 2018 (Doyle One Design layout); text unchanged from Doyle's 2014 web page
Base setup
- Mast step
- 12′ 6½″ from the centre of the transom at deck level to the aft edge of the mast step
- Base tension
- Uppers 150 lbs, lowers 80 lbs (equal both sides), mast straight
- Mast at deck
- Shim tightly where it passes through the deck
- Headstay sag (light air)
- With the backstay loose the headstay should be able to swing through a 12″ circle
- Jib leads (diagram)
- Swing a 7′ 9½″ arc from the forward headstay hole aft onto the cabin top; jib blocks 28″ apart (14″ each side of centreline) on 12″ tracks mounted on the cuddy top at 45° to the centreline
Shroud tension by wind (Loos Model A, lbs)
| Wind (unit not stated) | Lowers | Uppers |
|---|---|---|
| 0–4 | 0 | 110 |
| 4–8 | 0 | 110 |
| 9–14 | 80 | 150 |
| 15+ | 80 | 200 |
Outhaul by wind
| Wind (kn) | Outhaul |
|---|---|
| 0–5 | Eased 1½″ |
| 6–10 | Eased 1″ |
| 11–14 | Eased ½″ |
| 15+ | Maximum |
Backstay by wind
| Wind (unit not stated) | Backstay |
|---|---|
| 0–6 | None |
| 7–10 | ¼ |
| 11–15 | ½ |
| 16–18 | ¾ |
| 19+ | Max |
Trim by condition
- Rig tension
- More overall rig tension means more headstay tension.
- Mainsheet
- Top batten parallel to the boom; once up to speed trim harder with the top batten slightly to weather, but a batten hooked well to weather stalls the main.
- Traveller
- Car up to the inner edge of the windward seat so the boom is on or just below centreline; drop it progressively as the breeze builds.
- Outhaul
- Controls the lower third of the main; use it for helm balance.
- Cunningham
- Keep maximum draft 50% aft: none up to 10 kn, enough to remove most wrinkles at 11–15 kn, progressively tighter above.
- Vang
- Loose upwind in most conditions; offwind just enough for a top batten parallel to the boom. Watch boom bend in a breeze — Rhodes 19 booms are not strong.
- Jib luff
- Medium wrinkles at 0–10 kn, progressively smoother from 11 kn; ease it if short of power in chop.
- Jib leads
- Set so the luff breaks evenly when luffing slowly; forward breaks the bottom first, aft breaks the top first. Keep both telltales streaming.
- Backstay
- Bends the mast (flatter, more open upper main) and tightens the forestay (flatter jib entry); adjust the mainsheet with every backstay change.
- Heavy air (18+ kn)
- Sheets hard; over about 20 kn traveller down full time and play the main; outhaul max, cunningham hard, backstay between ½ and max played in waves and puffs. Some jib luff wrinkles are fine in chop, but expect to tighten the luff and move the leads aft; with heavy helm move them further aft, ease the jib for upper twist and add backstay. Keep the boat flat.
- Downwind
- Vang for a top batten parallel to the boom; ease cunningham, outhaul and backstay; pole height so the clews are level; 6–12″ of luff curl; pole square to the apparent wind. Reaching: head up in lulls and chop, bear away only in puffs. Running: gybe on the shifts.
- Identical PDF also on ussailing.org (https://www.ussailing.org/wp-content/uploads/2020/10/DoyleRhodes19TuningGuide.pdf; file re-saved October 2020 on upload, content unchanged).
- The class site links a 19 May 2014 print of Doyle's old web page (doylesails.com/onedesign/rhodes19/tuning.html) with the same numbers and text but no author names: https://cdn.shopify.com/s/files/1/0811/2449/1514/files/Rhodes_19_Tuning_Guide___Doyle_Sailmakers.pdf?v=1769451623
- The shroud and backstay tables give no wind unit; the outhaul table is headed in knots (the cunningham text also uses knots).
- The backstay table gives fractions of the available travel, not a measured unit.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Rhodes 19 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Rhodes 19 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Rhodes 19. Racing legality depends on your class or handicap rules; check them before changing equipment.