One-design race shop · Dinghy

Windmill Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Windmill

  • 1 verified part
  • 1 brand

Fit verified for Windmill

All Windmill equipment

1 part

  • Fit verified for Windmill

    Dynamic

    Dynamic Windmill Dolly

    Part # DYN-10079

    $650.00$886.36

Can’t find a part for your Windmill? Request a Windmill part

Go fast

Windmill tuning guide

The Windmill is tuned mainly with mast rake (measured with a boom-band radius from the headstay), spreader deflection and moderate shroud tension, then the jib leads and board angle. North Sails' guide is the only published one we found; its shroud figure is in pounds on a Loos gauge with no model named.

North Sails — Windmill Tuning Guide Not dated on the page

Written for
North Windmill main and jib (no model named; the main has a shelf foot)
Tension gauge
Loos gauge, model not stated; tension in lb
How it’s measured
Rake: hoist the jib without hanking it, unpin the forestay and swing it back to the mast; mark the zero point where the wire meets the top of the black band at the boom (upper band if there are two), then swing it forward and measure from that point to the upper forward deck/bow intersection. Centre the mast with a tape on the main halyard to each chine below the chainplates.
Source
North Sails, Not dated on the page

Base setup

Mast step
About 59–60" from station 0; the mast must be snug in the step and unable to twist
Spreader height
Standard 104–106" above the theoretical top of keel; some boats run up to 117"
Spreader length
About 15.5" from the mast surface, with spreaders at 106" and inboard chainplates, or at 117" with chainplates near the gunwale
Spreader deflection
Shrouds pushed about 2.5–3" outboard (limits side bend) and about 1.5–2" forward (limits fore-and-aft bend), checked at the light-air rake setting
Mast to shroud line
Aft edge of the mast about 5" forward of a straight line between the shrouds for a Kenyon "A" section; about 6.5" for a Proctor Lambda or Alpha Minus
Shroud tension
About 150 lb on a Loos gauge at the light-air rake setting. Without a gauge: moderately tight, so the shroud can be wiggled in a small circle without much effort. Heavier crews tighter, lighter crews looser.
Prebend check
At the 3'0" rake setting with the jib up, about ½–1" of forward bend at mid-mast
Partners
Mast straight and snug in the partners; side-to-side play depowers the rig too early
Jib lead (start)
Bearing point of the lead blocks about 83" aft of the jib tack pin, or set so the sheet lines up with the clew trim line
Jib lead (athwartships)
About 16–17" from centreline, set by the shackle length to the track slider: about 16" for light air, about 18" for heavy air

Mast rake (zero point at boom band to the deck/bow intersection)

ConditionRake measurement
Light air, full powerAbout 34.5"
Average light-air setting36"
Lighter crews / building breezeAbout 37"
Heavy airAbout 38"

Trim by condition

Rake & helm
If you point high but are slow, add rake and free the helm; if you're fast but can't point, take rake out. When overpowered, ease the jib halyard to rake aft.
Spreaders
If the spreaders drop to leeward upwind in 8–10 kn with the boom near centreline, loosen the rig or shorten the spreaders; Nicropress stops under the spreaders hold the angle.
Daggerboard
Stiff and tight in the trunk (carpet shims are class-legal). Fully down and forward in light air up to full hiking; as weather helm builds, raise it and/or angle it aft.
Mainsheet & vang
The vang should just go slack at maximum mainsheet tension. Light–medium: top batten about parallel to the boom; in very smooth water hook it about 5° to windward.
Speed vs pointing
Fast but not pointing: less rake, traveller nearer centreline, harder vang, jib leads forward. Pointing but slow: more rake, ease the traveller, more mast bend, ease an over-tight vang, jib leads aft.
Cunningham
Slack to about 10 kn; above that, just enough to remove luff wrinkles (moves draft forward, frees the leech).
Outhaul
The shelf foot makes it sensitive: ease 2–3" for power in chop and off the wind; tighten in heavy air or when overpowered.
Jib leads
Forward and a slightly looser sheet in chop; move aft as breeze and rake increase to twist the head open. If there's no trim line, draw one from the clew centre to mid-luff.
  • The guide gives no author, date or sail model, and no wind-range table: settings are described as light air, 8–10 kn, above 10 kn and heavy air.
  • North notes the exact numbers shift with chainplate position and spreader-bracket height; the deflection amounts matter more than the lengths.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Windmill resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Windmill by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
We have no current one-design class rules on file for the Windmill. Racing legality depends on your class or handicap rules; check them before changing equipment.