One-design race shop · Keelboat

Santana 20 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Santana 20

  • 51 verified parts
  • 12 brands
  • Fit checked Nov 2026

Fit verified for Santana 20

All Santana 20 equipment

51 parts

Can’t find a part for your Santana 20? Request a Santana 20 part

Official Harken dealer

Santana 20 deck layout

LOA
20' 2 1/2"
LWL
16'
Beam
8'
Draft
Fin Keel 4'
Draft
Wing Keel 32"
Displacement
1350 lbs.
Ballast (lead)
550 lbs.
Sail Area
204 sq. ft.

Backstay

Backstay — Harken layout for the Santana 20
Drawing: Harken

    Jib Halyard

    Jib Halyard — Harken layout for the Santana 20
    Drawing: Harken

      Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

      Go fast

      Santana 20 tuning guide

      The Santana 20 is tuned for rake, a base upper/lower shroud tension and adjustable aft lowers that invert the mast (inverse prebend) more as the wind builds, with genoa foot and leech distances as the trim reference. North reads tension on a Loos PT-1 (base 25/20) and Ullman on a Loos Model A (33/33), and they measure rake differently, so don't mix their numbers.

      North Sails — Santana 20 Tuning Guide Web page (posted 2017)

      Written for
      North main, genoa, class jib (small jib), full radial spinnaker
      Tension gauge
      Loos PT-1 (recommended over the Model A because it stays on the shroud and doesn't stretch)
      How it’s measured
      Rake: forestay disconnected and pulled taut up the mast on the jib/spinnaker halyard, bottom of the black band marked (the mark should be 22″ above the mast bottom); reconnect, add backstay to straighten the forestay, and measure from the mark to the centre of the forestay pin. Centre the masthead with a tape on the genoa halyard to rail marks about 10″ forward of the shrouds. Turns are full turns of an open-body turnbuckle, always counted from base.
      Source
      North Sails, Web page (posted 2017)

      Base setup

      Rake
      51″ (about 50″ for light crews in more breeze)
      Forestay mark
      Bottom of the black band 22″ above the bottom of the mast
      Base tension
      Uppers 25 / lowers 20 on the PT-1 (the 10–12 kn setting)
      Aft lowers
      On an adjustable track; at maximum they should invert the mast at least 3¼–3½″ (release the backstay first)

      Rig settings (turns from base; one turn = one full turn of an open-body barrel)

      Apparent wind (kn)UppersLowers
      0–5−1−1
      5–10−½−½
      10–12Base: 25Base: 20
      12–15+1½+2
      15–20 (genoa)+2+2½
      15–20 (jib)Base+2
      20–25 (jib)+2+2½

      Upwind references

      Wind (kn)0–56–1213–1819+
      Aft lowers (inverse bend)Tensioned, mast straight1–1¾″3–3½″4″
      Outhaul (from black band)1–2″½″MaxMax
      Genoa leech from spreader tip2–3″2–3″4–5″6″
      Genoa foot from turnbuckle3–4″1–2″AgainstAgainst
      Genoa luff tensionSmoothSlight wrinkleSmoothSmooth
      Leech lineJust enough to stop flutterJust enough to stop flutterJust enough to stop flutterJust enough to stop flutter

      Trim by condition

      Main, 0–5 kn
      Speed before pointing. Aft lowers set so the mast is straight; sheet until the top batten cups slightly to windward, then add backstay until it is parallel to the boom; vang off; traveller up so the lower battens sit just to leeward of the backstay; outhaul 1–2″ off max (looser in chop); cunningham only for big wrinkles.
      Main, 6–12 kn
      Aft lowers 1–1¾″ inverse; traveller up with the boom on centreline (ease for helm or heel); outhaul ½″ off; cunningham removes all wrinkles; vang snug. To point, sheet so the top-batten telltale stalls 50–80% of the time.
      Main, 13–18 kn
      Aft lowers 3¼–3½″ inverse; backstay until the top batten twists about 15° to leeward; cunningham smooth; vang holds the boom at sheeted height; outhaul max.
      Main, 19+ kn
      Aft lowers max (4″); backstay for about 20° twist; hard vang; outhaul max; traveller to the cockpit edge. 'Super twist' if still overpowered: traveller to windward and sheet eased so the boom is on centreline, outhaul eased ½″.
      Genoa, 13–18 kn
      Halyard tighter; foot against the turnbuckle, leech 4–5″ off; depower by easing the sheet 1–2″. Keep the windward telltales at about 45° for best VMG.
      Jib
      Crossover often in the 13–18 kn range. Use a 2:1 sheet. In 19+ sheet to inboard cabin-top tracks at 11° off centreline (19½″ outboard of centreline behind the mast); halyard just removes wrinkles; top telltales break slightly before the lower ones.
      Downwind main
      Release the aft lowers at the windward mark; backstay off (some on above 15 kn); jib halyard to the tack hook to hold the mast forward; outhaul 2″ off; cunningham off; vang so the top batten is parallel to the boom.
      Spinnaker
      Pole at the mast 44½″ above the deck, level with the horizon; halyard fully up; pole square to the apparent wind; slight luff curl; ease the sheet 5–12″ in puffs; keep the pole at least 2–3′ off the headstay.
      • The rig-settings table is labelled 'apparent wind'; the trim sections use plain wind-speed bands.

      Ullman Sails — Santana 20 Tuning Chart, Tuning Guide and Sailing Guide 2014 in the file names (PDF metadata dated April 2008)

      Written for
      Ullman main (with spreader window), genoa, small class jib on inboard tracks, radial-head spinnaker
      Tension gauge
      Loos Model A
      How it’s measured
      Rake: tape tied to the main halyard (not the shackle), two-blocked, backstay just taking the slack out of the forestay; measure to the centre of the transom where hull and transom meet near the waterline. Centre the masthead with a tape on the spinnaker halyard to rail marks about 10″ forward of the chainplates.
      Source
      Ullman Sails, 2014 in the file names (PDF metadata dated April 2008)

      Base setup

      Rake
      31 ft (adjust with the forestay turnbuckle)
      Base tension
      Uppers 33 (320 lb) / lowers 33 on the Model A
      Aft lowers
      Equal both sides; at their maximum aft position about 3–4″ of inverse prebend, roughly 11 on the gauge

      Tuning chart (Loos Model A)

      Wind (kn)0–56–1213–1819+
      Uppers33333335
      Lowers33353537
      Inverse prebend (aft lowers)Straight1–2″3–4″4″
      HeadsailGenoaGenoaJibJib
      Genoa foot from shrouds3–4″1–2″TightSee 'Genoa trim'
      Jib halyardSmoothWrinklesSmoothSmooth
      Main cunninghamLooseWrinklesSmoothSmooth
      Outhaul (from band)1–2″½″TightTight
      Upwind vang & top-batten twistNo vangNo vang10–15°15–20°
      Traveller (from centreline)+2″Center0 to −3″0 to −8″
      BackstayLooseMediumTightMaximum

      Trim by condition

      Main, 0–5 kn
      Mast straight with a little backstay; sheet until the top batten hooks 5° to weather, then backstay until it is parallel to the boom; boom on centreline; no vang; outhaul 1″ off max in flat water, 2″ in chop; slight luff wrinkles.
      Main, 6–12 kn
      Aft lowers for 1–2″ inverse; sheet and backstay as in light air; cunningham max loose; play the traveller and hike.
      Main, 13–18 kn
      Aft lowers 3–4″ inverse; trim hard and backstay until the top batten twists 10–15°; outhaul max; cunningham smooth; take the slack out of the vang.
      Main, 19+ kn
      Aft lowers max (4″); 15–20° of twist; outhaul and cunningham tight; vang hard; drop the traveller.
      Genoa
      0–5 kn: luff just smooth, foot 3–4″ from the turnbuckles, leech 2–3″ off the spreader tip, leech/foot lines eased. 6–12: slight luff wrinkles, foot 1–2″, leech 2–3″. 13–18: halyard tighter, foot against the turnbuckles, leech 4–6″; ease a couple of inches in big puffs. 19+: only with big waves and heavy crew.
      Small jib
      Use the inboard class tracks; halyard just removes wrinkles; top telltales break slightly first; top batten twisted open 5–10°, middle 0–5°; leech 3–5″ inside the outboard end of the spreader.
      Downwind
      Aft lowers fully forward and backstay eased so the mast rakes forward; outhaul eased 2–3″; cunningham off; vang so the top batten is parallel to the boom.
      Spinnaker
      Halyard fully up; pole height so the luff curls just above half height; pole about 90° to the mast; sheet to a slight luff curl.
      Crew
      Recommended crew weight 490–600 lb, sitting close together at the widest part of the boat.
      • Three Ullman documents: the chart (linked), the Tuning Guide (https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Santana-20-Tuning-Guide-2014.pdf) and the Sailing Guide (https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Santana-20-Racing-Guide-2014.pdf). The PDFs' internal titles still read 'Melges 24 Tuning Guide' (template metadata), and their creation dates are April 2008 although the file names say 2014.
      • The chart's 6–12 kn cunningham says 'Wrinkles' while the sailing guide says max loose.
      • Ullman doesn't publish these on its own site any more; the links are to canadianboating.ca copies.

      Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the Santana 20

      Technical

      Santana 20 resource centre

      How we verify parts

      Fit verified
      Each part listed here was matched to the Santana 20 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
      Class rules
      Fitting a part is not the same as it being legal for racing. Read the current Santana 20 class rules before changing equipment, and ask your class measurer if a part is not original equipment.