One-design race shop · Dinghy
Highlander Race Shop
Everything you need to prepare, compete, and win.
Highlander parts
Tell us what your Highlander needs
We list parts for a class only after checking them against the builder’s specification and the class rules. Send us the part, position or part number and our rigging team will source it.
Go fast
Highlander tuning guide
The Highlander is rigged very tight (leeward shroud firm until all three crew hike), with diamonds set before stepping to match mast bend to the main and rake of about 30′4″–30′7″ to the transom/back-deck joint. Both published guides quote tensions on the Loos Model A, but their rake and diamond numbers differ, so use the one written for your sails.
Quantum Sails — Highlander Tuning Guide 2018 (Karl Felger, Quantum Cleveland; Bill Wiggins, Quantum Charleston)
- Written for
- Quantum Highlander main (large spreader window), jib, spinnaker
- Tension gauge
- Loos tension gauge, Model A
- How it’s measured
- J: forward face of the mast at the bottom to the front of the forestay. Rake: top of the mast to the intersection of the transom and back deck, with proper rig tension.
- Source
- Quantum Sails, 2018 (Karl Felger, Quantum Cleveland; Bill Wiggins, Quantum Charleston)
Base setup
- J
- Minimum 67″
- Forestay tension
- 28–31 on the Model A; leeward shroud stays firm until all three crew are on the high side hiking
- Rake
- 30′4″
- Diamonds (Model A)
- Top 4 (0–2 for lighter crews); middle 16; bottom 16
- Jib lead
- Normal position 9′5″ aft of the jib luff-wire attachment point (all wind ranges)
Trim by wind (knots)
| Control | Light (0–7) | Medium (8–14) | Heavy (15+) |
|---|---|---|---|
| Main halyard / cunningham | Slight luff wrinkles | Enough to remove luff wrinkles | All controls maxed |
| Outhaul | Eased for depth low down | 1″ between shelf-foot seam and boom | Maxed |
| Bridle / traveller | Bridle raised; traveller may go to weather | Bridle so the upper batten just hooks when two-blocked | Ease mainsheet aggressively |
| Main top batten | Parallel to boom; top telltale 100% (speed) or stalled 75% at full speed (point) | 8–11 kn: hooked 5° (speed) to 8° (point); 11–14 kn start depowering | Eased to keep balance |
| Jib halyard / cloth | Loose, slight wrinkles | Remove wrinkles | Pulled on hard |
| Jib upper batten | 5° out from centreline | Parallel to centreline | Parallel to centreline |
| Main backwind | Never | Never | Up to a few feet behind the luff |
Trim by condition
- Diamonds
- Lower and middle diamonds too loose make the main too flat; too tight and it won't flatten in breeze. The upper diamond reflects crew weight and style: less tension lets the top bend and depower.
- Vang (medium)
- Take out the slack so boom height and leech tension stay constant when easing.
- Spinnaker
- Running: little or no luff curl, tack level with the clew, centre seam parallel to the mast, pole perpendicular to apparent wind. Reaching: up to 6″ of curl and the tack slightly lower than the clew.
North Sails — Highlander Tuning Guide Rev. Q05 (undated web page)
- Written for
- North Highlander main, standard inboard jib, clewboard jib, spinnaker
- Tension gauge
- Loos Model A (forestay and diamonds)
- How it’s measured
- Rake with a 50 ft tape on the main halyard from the top of the mast to where the transom meets the back deck, rig very tight. Bridle height from the back deck to the top of the block.
- Source
- North Sails, Rev. Q05 (undated web page)
Base setup
- J
- At least 67″
- Rake
- 30′5″ to 30′7″ with the rig very tight
- Rig tension
- Very tight: the leeward shroud just stays taut with all three crew on the high side starting to hike. Forestay 25–32 on the Loos Model A.
- Lower diamonds
- Squeeze to touch the mast no further than 4″ from the attachments; 15–18 Loos
- Upper diamonds
- Squeeze to touch the mast no further than 8″ from the attachments; 4–6 Loos
- Older gold aluminium / wood masts
- Diamonds about 4–5 Loos numbers lower
- Mast butt
- 3/16″ to 1/4″ spacer under the back of the aluminium butt casting (less reverse bend in light air, more bend in heavy air)
- Standard jib lead
- Lateral 15–16″ off centreline; fore-aft so the sheet meets the seat about 9′4″ from the jib luff-wire attachment at the stem plate; back 1″ at 15–18 mph, 2″ above 18 mph
- Clewboard jib lead
- Start on the middle clewboard hole; lead 16½–17″ off centreline (at the sheave exit); move the sheet forward on the clewboard in heavy air
Bridle traveller height (deck to top of block)
| Condition | Height |
|---|---|
| Fixed height | 22″ |
| Adjustable, very light air | 26″ |
| Adjustable, very heavy air | 20″ |
Outhaul (boom side to shelf seam)
| Condition | Gap |
|---|---|
| Upwind | 1½–2″ |
| Light air or choppy seas | 2½″ |
| Above 18 mph | Hard crease tack to clew |
| Downwind | 5″ (shelf open) |
Trim by condition
- Cunninghams
- Just enough to barely remove wrinkles: slight crow's feet at the jib hanks, slight horizontal wrinkles on the lower quarter of the main.
- Jib
- Sheet extends the pencilled trim line from the clew (slightly aft of it in heavy air with leads back); upper batten 5–10° out from centreline.
- Mainsheet
- Upper batten parallel to the boom (sight from under it); may hook in very light air; up to 20° past parallel in very heavy air. Ease the traveller down in puffs and back up in lulls.
- Vang
- Downwind keep the upper batten parallel to the boom and dump it in puffs; upwind moderate to heavy vang bends the mast and flattens the sail.
- Spinnaker
- 6–12″ luff curl; 2″ sheet adjustments; ease up to 3″ in puffs so the skipper can bear off; clews even, centre seam parallel to the mast.
- North's rake (30′5″–30′7″) is 1–3″ longer than Quantum's 30′4″, and its upper diamonds (4–6) and lowers (15–18) differ from Quantum's 4/16/16.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Highlander resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Highlander by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Highlander class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesOfficial Class Specifications updated 14 March 2019
- Class associationsailhighlander.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Highlander part