One-design race shop · Dinghy
Mirror Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Mirror
All Mirror equipment
7 parts
Fit verified for Mirror
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Mirror
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Mirror
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Mirror
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Mirror parts match these filters.
Can’t find a part for your Mirror? Request a Mirror part
Go fast
Mirror tuning guide
Mirror tuning is mainly rake (shroud-plate holes and forestay tension), shroud tension, jib tack height and jib sheeting. Rake depends on the rig (gaff or Bermudan), the hull builder (wooden, Winder, Goodwin, Trident) and the datum used, so only compare numbers measured the same way; tension is read on Loos or Superspar gauges or given in pounds.
P&B (Pinnell & Bax) — Mirror Tuning Guide 2021 (PDF dated July 2021)
- Written for
- P&B Mirror sails (Bermudan chart; gaff rake given separately)
- Tension gauge
- Loos tension gauge on the shrouds (model not stated)
- How it’s measured
- Bermudan rake: hoist a tape to read 4 m 22 at the top of the gooseneck black band (datum), then swing to the top of the transom. Gaff rake: with 180 lb forestay tension, boat on its side, from the pin of the masthead halyard sheave to the top outside of the transom.
- Source
- P&B (Pinnell & Bax), 2021 (PDF dated July 2021)
Base setup
- Rake (chart)
- For Winder hulls, 5020 mm; Goodwin and wooden hulls need slightly more rake (wooden hulls 4995–4920 mm)
- Changing rake
- Shrouds down a hole = more rake (smaller number); up a hole = less rake (bigger number). When overpowered rake back half a hole to 5010 mm and tension to 18 on the Loos gauge.
- Rig tension
- Start at 15 on the gauge, maximum 18; add tension as the wind rises to stop jib luff sag
- Fairleads
- As far back and as high as possible on the thwart; bearing points 750 mm apart; bow (outside edge, middle of the bow) to fairlead bearing point 997 mm
- Spinnaker pole
- Bow to pole-end bearing point 1430 mm; pole eye on the mast 1070 mm up
- Gaff rig rake
- 3540–3570 mm
Settings by wind (Bermudan rig; tension on Loos gauge)
| Wind (kn) | 0–4 | 5–9 | 10–14 | 15–19 | 20–24 | 25+ |
|---|---|---|---|---|---|---|
| Mast rake | 5020 mm | 5020 mm | 5020 mm | 5020 mm | 5010 mm | 5010 mm |
| Shroud tension | 15 | 15 | 15 | 17 | 17 | 17 |
| Kicker | Loose | Loose | Quite tight, top telltale stalling | Tighter | Lots | Lots |
| Why | Top telltale stalling 30% of the time | Top telltale stalling 30% of the time | Top telltale stalling 30% of the time | Control twist and blade out the main | Control twist and blade out the main | Control twist and blade out the main |
| Outhaul | Tight crease along foot | Tight, no crease | Loose, 15 cm gap | Tighten | Tighten | Tight |
| Downhaul | None | None | None | Slight | On hard with increasing wind | On hard |
| Jib height (from uppermost point on deck) | 15 mm | 25 mm | 25 mm | 25 mm | 15 mm | Low as possible |
| Jib tension | 2" of tight | 1" of tight | Tight | Tight | Tight | Ease to foot |
Trim by condition
- Outhaul
- Average upwind setting: foot just touching the leeward side of the boom, then adjust for wind and waves.
- Jib tack
- Raise or lower for the conditions, using the top of the gunwale as the datum.
- The wooden-hull range is printed high to low (4995–4920 mm).
UK Mirror Class Association (Ash Shepherd) — Mirror rig set-up 2017 (PDF dated April 2017)
- Written for
- Gaff and Bermudan rigs (class sails)
- Tension gauge
- None; tension set by a multi-turn forestay lashing (a healthy 'thrum' when a shroud is plucked)
- How it’s measured
- Gaff: boat on its side, tape from the pin of the main halyard sheave to the horizontal/aft face of the transom. Bermudan: tape on the main halyard to 4,220 mm at the top of the gooseneck black band, then to the rear edge of the transom on the centreline.
- Source
- UK Mirror Class Association (Ash Shepherd), 2017 (PDF dated April 2017)
Base setup
- Gaff rake
- Minimum 3,550 mm; 1–2 cm more is fine
- Bermudan rake, level transom (wooden and plastic, e.g. Trident)
- About 5,010 mm or 5,020 mm
- Bermudan rake, curved transom (Winder)
- Maximum rake 4,990 mm; 5,020 mm and 5,010 mm are good, depending on shroud plates and lengths
- Gaff sail head
- Up to the bottom of the black band on the gaff, about 76 mm from the gaff end; gaff pulled tight to the mast sheave
- Older wooden boats
- Shroud plates often give too upright a rake; multi-hole plates allow adjustment
Trim by condition
- Helm check
- Close-hauled and level with a light grip: slowly turning into wind = correct rake; turning quickly into wind = too much rake; bearing away = too upright.
- Jib halyard
- Tight enough that the luff doesn't sag between the hanks, but not so tight that a bulge runs parallel to the forestay; fine-tune while beating.
- Written for the UK class's race-training resources; record your starting measurements and photos before changing anything.
Sailboats Speedsails — Mirror Tuning Guide by Sailboats Speedsails Undated web page
- Written for
- Speedsails Mirror sails (gaff and Bermudan)
- Tension gauge
- Pounds, with Superspar rig-tension gauge numbers; measured on a side shroud at the same height (eye level) each time
- How it’s measured
- Gaff rake: top of mast to top of transom with 180 lb forestay tension. Bermudan rake: tape to a 4102 mm datum at the gooseneck back band, then swing to the top of the transom.
- Source
- Sailboats Speedsails, Undated web page
Base setup
- Mast step, gaff
- 2174 mm from the forward face of the transom to the centre of the mast step (class rule 2160 mm ± 15 mm)
- Mast step, Bermudan
- 2174 mm from the forward face of the transom to where the front of the spar meets the foredeck butt strap
- Rig tension, all rigs
- 160–180 lb (15–18 on a Superspar gauge)
- Rake, gaff
- 3540–3570 mm
- Rake, Bermudan
- 4921 mm with 160 lb shroud tension (15 on the Superspar gauge); shrouds down a hole for more rake, up a hole for less
- Jib fairleads
- Bearing surface 30 mm from the side tank, as far aft as possible on the thwart
- Main luff lacing
- Tight enough to hold the luff about 30–40 mm from the mast with the downhaul on
Jib sheet
| Conditions | Setting |
|---|---|
| Above 12 kn, both fully hiking | Bar tight |
| Crew to windward but not hiking | Eased 5–10 mm |
| Crew progressively lighter / moving inboard | Eased progressively, up to 25 mm maximum |
| Very choppy and light | Ease a further 5 mm |
Jib tack height (above the bow knees)
| Conditions | Height |
|---|---|
| Light winds | Up to 25 mm |
| Strong conditions | 10 mm |
Kicker
| Conditions | Setting |
|---|---|
| Very light (crew to leeward or middle) | Just take out the slack; control the leech with the mainsheet |
| Wind increasing (crew on the windward deck or gunwale) | Top leech telltale flying about 80% of the time |
| Above 15 kn (both fully hiked) | Top telltale flying continuously; use as the power control |
| Downwind | Ease so the leech telltales fly; let off a lot on a run |
Outhaul
| Point of sail | Setting |
|---|---|
| Upwind | About 100 mm between the main foot and the boom |
| Reaches | Eased a further 38–50 mm (leave on for a windy close spinnaker reach) |
| Run | Eased only 5–10 mm |
Trim by condition
- Jib halyard
- Just tight enough to remove creases between the hanks; a long vertical crease along the forestay means too much.
- Jib tack height
- Raising it loosens the foot and tightens the leech (upper telltale breaks first); lowering it tightens the foot and opens the upper leech.
- Downhaul
- Only to remove the large luff creases.
- Spinnaker
- Pole set so the clews are level about 90% of the time; stopper knots keep the pole just off the forestay in light air; drop the pole a few inches if the kite won't fly.
- Rake datum (4102 mm) differs from P&B and the class guide (4220 mm), so the Bermudan rake numbers aren't directly comparable.
North Sails — Mirror Tuning Guide Undated web page
- Written for
- Not stated (gaff and Bermudan rigs)
- Tension gauge
- Loos tension gauge on the shrouds (model not stated)
- How it’s measured
- Rake from the top of the mast (or gaff) to the centre top of the transom.
- Source
- North Sails, Undated web page
Base setup
- Rake, wooden hulls
- 4950–5000 mm (gaff or Bermudan)
- Rake, Goodwin hulls
- 4975–4850 mm (printed in that order)
- Rake, Winder hulls
- 5000–5100 mm
- Shroud tension
- 12–16 on older boats; new wood and FRP boats take 18–22. Record it so it's repeatable.
- Fairleads
- As far back and as high as possible on the thwart (a 25 mm block is allowed); bearing surfaces roughly 750 mm apart
Jib tack height
| Conditions | Tack above deck |
|---|---|
| Starting point | 30 mm |
| Light and moderate wind and waves | 50 mm |
| Strong winds | Level with the deck |
| Very strong winds | 10–20 mm below deck level |
Trim by condition
- Outhaul
- Upwind, foot just touching the leeward side of the boom; in chop when not overpowered leave 2 cm; tight in strong winds. Downwind it can be eased 5 cm for more power.
- Kicker and twist
- Keep leeches open enough that the telltales don't stall; over-closing makes the boat slow and slide sideways.
- Jib sheet
- If the boat slows against the boats around you or bounces in place, ease the jib 1 cm. Mark the sheets and the kicker to repeat fast settings.
- Gaff and Bermudan rakes are lumped together here; the class and P&B guides give a separate, much shorter gaff number.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Mirror resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Mirror by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Mirror. Racing legality depends on your class or handicap rules; check them before changing equipment.