One-design race shop · Dinghy
Enterprise Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Enterprise
All Enterprise equipment
19 parts
Fit verified for Enterprise
Forespar
Forespar Aluminum Small Whisker Pole Twist-Lock (ADJ 4-8 Ft.) 53-93 In. (for 16 ft. Boat Max.) - 1 In. Dia.
Part # FOR404000
$134.36
$167.95Fit verified for Enterprise
Forespar
Forespar Aluminum Small Whisker Pole Twist-Lock (ADJ 4-8 DL) 53-93 In. (for 16 ft. Boat Max.) - 1 In. Dia.
Part # FOR404100
$147.96
$184.95Fit verified for Enterprise
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Enterprise
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Enterprise
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Enterprise
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Enterprise
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Enterprise
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for Enterprise
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Enterprise
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Enterprise
Schaefer
Schaefer Wind Indicator - Little Hawk Race
Part # SCHH007F00
$93.00
Fit verified for Enterprise
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Enterprise
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Enterprise
Schaefer
Schaefer Wind Indicator - Little Hawk MK 1
Part # SCHH003F00
$34.70
Fit verified for Enterprise
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for Enterprise
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Enterprise parts match these filters.
Can’t find a part for your Enterprise? Request a Enterprise part
Go fast
Enterprise tuning guide
Enterprises are usually set at about 400 lb shroud tension with rake around 21′ 1″–21′ 2″ (P&B's 2025 sheet uses 6490 mm, dropping to 6445 mm and 450 lb in heavy air), and spreaders tuned to each sailmaker's prebend target (North wants a straight mast; Speed about 1″). Rake is measured to the top or back edge of the transom in most guides but to the transom centre in North's, so read each guide's datum.
Pinnell & Bax — Enterprise Tuning Guide 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-ENT)
- Written for
- Not stated (Pinnell & Bax guide); written for the Selden D+ or Super Spar M2 (lower sleeve) mast
- Tension gauge
- Super Spar rig gauge on the shrouds (3 mm 1x19 wire), lb
- How it’s measured
- With rig tension on, pull the tape to the masthead on the main halyard (cleated), check 18′ 6″ (5640 mm) at the top of the gooseneck band, then measure to the top of the transom on the centreline. Spreader A: from the line between spreader ends perpendicular to the mast track; B: mast side wall to spreader end.
- Source
- Pinnell & Bax, 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-ENT)
Base setup
- Spreaders, Selden
- A 160 mm / B 413 mm
- Spreaders, Super Spar
- A 160–165 mm / B 410 mm
- Mast foot
- As far forward as the rules allow: 2689 mm from the aft of the mast at deck to the aft of the transom; P&B Rondar mast steps are 25 mm high (a lower step reduces rake)
- Centreboard bolt
- As far aft as allowed: 2216 mm from the aft face of the transom to the foreside of the bolt's bearing point
- Centreboard depth
- Close to the 826 mm maximum extension below the keel (excluding keel band)
- Hull weight
- Down to the 94 kg minimum; slot gasket overlapping ¼″ (6 mm) and fitted under tension
- Jib fairleads
- Close to the 595 mm minimum from the centreline (measured to the outside edge)
- Jib sheet line
- Extension of the sheet should meet the luff wire 1680 mm from the tack
- Kicker
- 16:1 cascade; attached 21″ (530 mm) from the inboard end of the boom; can be moved aft up to 3″ (75 mm) to induce lower mast bend
Settings by wind (rig tension in lb, Super Spar gauge)
| Wind | Light | Medium | Heavy |
|---|---|---|---|
| Mast rake | 6490 mm | 6490 mm | 6445 mm |
| Rig tension | 400 lb | 400 lb | 450 lb |
| Outhaul upwind | Tight | Ease 18 mm | Tight |
| Outhaul reaching / off wind | Ease 12 mm | Ease 90–115 mm | Ease 50–75 mm |
| Outhaul running | Tight | Tight | Tight |
| Cunningham upwind | Off | Up to 12 mm | Up to 75 mm |
| Cunningham reaching / off wind | Off | Off | Off |
Trim by condition
- Mast straightness
- With tension on, sight up the luff groove: it must be straight fore-and-aft and sideways. A sideways bend at the spreaders usually means a worn step; pack Mylar under the heel on the side it bows towards. P&B calls this the biggest single fault in slow Enterprises.
- Jib sheeting
- Medium: in tight until a hard crease runs along the foot. Light, as the crew thinks of sitting in: ease ¼″ (6 mm) so the foot is smooth. Heavy: as hard as possible (the helm may need to help).
- Kicker
- Light–medium: top telltale stalling about 70% of the time. Heavy: loads, until creases appear from the spreaders to the clew.
- Outhaul
- 4:1 system with a stopper knot at the maximum setting (e.g. 4½″ / 115 mm).
- Mainsheet
- Block fixed on the centreline; P&B prefers no ratchet block so the main can be played quickly to keep the boat flat.
- Jib sticks
- Carry a maximum-length stick for goose-winging and a minimum-length one for broad reaches with the jib to leeward (faster in light–medium air; limiting in heavy air and waves).
- Rig faults
- Creases from the mast towards the clew = too much bend: check tension, then angle spreaders forward. Excess cloth by the mast or jib backwinding = too little bend: ease cunningham, then sweep spreaders aft.
- The kicker-position text reads 'except in windy conditions this position can be moved aft', which is ambiguous; it most likely means the attachment can be moved aft in windy conditions.
North Sails — Enterprise Tuning Guide Posted 2017
- Written for
- North Enterprise main and jib
- Tension gauge
- Rig tension gauge on the shrouds, 3 mm wire scale (model not named), lb
- How it’s measured
- Rake from the top of the mast to the centre of the transom, jib hoisted and tension fully on.
- Source
- North Sails, Posted 2017
Base setup
- Spreader tip to tip
- Superspar M2 Sleeved 780 mm; Proctor D+ 760 mm
- Spreader length (tip to mast wall)
- Superspar M2 Sleeved 410 mm; Proctor D+ 410 mm
- Rig tension
- 400 lb, all conditions
- Mast rake
- 6470 mm
- Mast shape
- Should be straight with no mainsail hoisted
Trim by condition
- Mainsail
- Make sure it is fully hoisted; halyards stretch.
- Cunningham
- None until overpowered in heavy air, then progressively harder to move draft forward in the top and free the upper leech.
- Outhaul
- Beating: tight in light and heavy air, eased about 12 mm in medium. Running: tight. Reaching: fully eased in medium, eased 25 mm in light, tight in heavy.
- Jib lead
- The sheet line through the clew should divide the luff about in half; in Force 3 all telltales should break together. Sheet hard in medium–heavy air; ease about 12 mm in light air. Keep the same lead except in very heavy air, then move it back 25 mm.
- The class association's comparison table gives North spreader deflections of 162 mm (Superspar) and 175 mm (Proctor) for a straight mast.
Speed Sails (Sailboats) — Enterprise Tuning Guide by Sailboats Speedsails Undated web page; the class site's PDF copy (sailenterprise.co.uk/wp-content/uploads/Enterprise.pdf) carries 2007 file metadata
- Written for
- Speed Sails Enterprise sails; Superspar or Proctor mast
- Tension gauge
- Not named; measured on the shroud at eye level, lb
- How it’s measured
- Jib hoisted at 400 lb; tape on the main halyard reading 18′ 6″ to the top of the black band at the gooseneck, then swing to the top of the transom.
- Source
- Speed Sails (Sailboats), Undated web page; the class site's PDF copy (sailenterprise.co.uk/wp-content/uploads/Enterprise.pdf) carries 2007 file metadata
Base setup
- Spreader length
- Superspar 410 mm; Proctor 420 mm (mast side wall to shroud)
- Spreader deflection
- 171 mm (both masts)
- Rig tension
- 400 lb in all conditions; fine-tune with a small chain plate on the jib halyard
- Mast rake
- 21′ 1½″–21′ 2″ to the top of the transom
- Chain plate steps
- Each half-hole changes rake by about ½″
- Prebend
- 1″ at spreader height
Jib fairleads
| Conditions | Fairlead |
|---|---|
| Below 8 kn | One hole forward |
| Normal | Sheet line bisects the leech–foot angle |
| Above 15 kn | One hole back |
Outhaul
| Point of sail | Setting |
|---|---|
| Upwind | To the black band |
| Upwind, drifting | Eased ¼″ |
| Reaching | Eased 1½–2″ |
| Running | Eased ½″ |
Trim by condition
- Jib sheet
- Bar tight in medium and heavy air (a crease across the foot); ease ¼″ when the crew comes off the side deck and ½″ when the crew sits to leeward.
- Jib sticks
- Carry a maximum-length running stick and a minimum-length reaching stick; over-trim slightly with the reaching stick so the bottom leeward telltale lifts.
- Main halyard
- Hoist to the bottom of the black band; ½″ below it (one notch) under 10 kn.
- Kicker
- Slack out in very light air; top telltale flying about 80% as the mast starts to bend; above 15 kn it is the power control. Downwind keep the leech telltale flying. If you run out of kicker, move the kingpost chain plate pin down a hole (up a hole if you can't ease enough on a run).
- Cunningham
- Only upwind in 15 kn and above, to remove some creases; never bar tight; never downwind.
- The class association's comparison table lists Speed Sails at Superspar 410/177 mm and Proctor 420/171 mm, which differs from the 171 mm Superspar deflection here.
- The kingpost chain-plate advice in the kicker note is in the PDF copy on sailenterprise.co.uk (Enterprise.pdf), not on the current web page; the numbers are otherwise the same in both.
Enterprise Association — Enterprise Tuning Guide (with sailmaker spreader table) Undated (mentions a 2009 flyaway jib-stick change; PDF file created 2012)
- Written for
- General; spreader figures for North, Pinnell & Bax and Speed Sails
- Tension gauge
- Rig tension gauge on the shroud (not named), lb
- How it’s measured
- Mast foot 2689 mm from the aft face of the transom to the back of the mast. With the jib hoisted at 400 lb, hoist a tape to read 18′ 6″ (5640 mm) at the top of the gooseneck black band, then measure to the back edge of the transom.
- Source
- Enterprise Association, Undated (mentions a 2009 flyaway jib-stick change; PDF file created 2012)
Base setup
- Mast rake
- 21′ 2″ (6452 mm) at 400 lb as the best upwind/downwind compromise
- Light winds / frail boats
- 300–350 lb; no loss of speed below Force 4
- Mast foot
- As far forward as the rules allow: 2689 mm (transom aft face to back of mast)
- General deflection
- 160–165 mm for flatter sails; 170–180 mm+ for older or fuller sails
- Prebend
- Printed as “about ½″/4″” at spreader height (the “/4″” looks like a typo); with North settings, no prebend
- Jib fairleads
- Class minimum 595 mm from the centreline (inside face); sheet line should cross the luff 1680 mm from the tack
- Kicker
- Boom attachment 530 mm from the inboard end; 16:1 cascade common
- Jib sticks
- Running: class maximum 1328 mm; reaching: minimum 1256 mm
- Hull weight
- No less than 94 kg including up to 4.5 kg of correctors
Sailmaker spreader settings (length / deflection)
| Sailmaker | Superspar length | Superspar deflection | Proctor length | Proctor deflection |
|---|---|---|---|---|
| North Sails | 410 mm | 162 mm (straight mast) | 410 mm | 175 mm (straight mast) |
| Pinnell & Bax | 410 mm | 165 mm | 413 mm | 160 mm |
| Speed Sails | 410 mm | 177 mm | 420 mm | 171 mm |
Trim by condition
- Mast upright
- With the tape still hoisted, measure to the deck beside each shroud and even them up; re-check rake after any change.
- Sideways bend
- An uneven step can bend a straight mast: shim under the foot on the side it bows towards.
- Traveller
- Fix the lower mainsheet block on the centreline.
- North's own guide measures rake to the centre of the transom (6470 mm), not the back edge used here.
Enterprise Association — Boat Set Up & Tune Undated (PDF file created 2012)
- Written for
- General
- Tension gauge
- Gauge not named, lb, always read at the same height
- How it’s measured
- Same method as the class Tuning Guide (18′ 6″ / 5640 mm datum, back edge of the transom).
- Source
- Enterprise Association, Undated (PDF file created 2012)
Base setup
- Mast rake
- 21′ 2″ (6452 mm) at 400 lb; most top sailors use 21′ 1″–21′ 3″
- Older boats / light wind
- 300–350 lb (one successful club sailor uses 280 lb on a 39-year-old boat)
- Mast foot
- 2689 mm from the aft face of the transom to the back of the mast
- Jib fairleads
- Inside edge 59.5 cm from the centreline (119 cm apart)
- Jib sheet line
- Should meet the luff at its midpoint, 1918 mm from the tack
Trim by condition
- Older masts
- On older Proctor masts (e.g. gold Proctor E) the top sheave sits about 4″ (10 cm) above the top band rather than 2″ (5 cm), which skews rake readings; hold the halyard 2″ above the band with the boat on its side and measure from there.
- Halyards
- Wire jib halyard tensioned with a Highfield lever; low-stretch main halyard.
- The jib-lead crossing point on the luff differs from the Tuning Guide (1918 mm vs 1680 mm from the tack).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Enterprise resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Enterprise by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Enterprise class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesEffective 1 March 2023 (World Sailing, per filename and search excerpt)
- Class associationsailenterprise.co.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Enterprise part