One-design race shop · Dinghy
M-16 Scow Race Shop
Everything you need to prepare, compete, and win.
Fit verified for M-16 Scow
All M-16 Scow equipment
1 part
Fit verified for M-16 Scow
Harken
Harken Canvas M-16 Scow Mooring Cover (Top Gun)
Part # HAC8069
$996.45
No M-16 Scow parts match these filters.
Can’t find a part for your M-16 Scow? Request a M-16 Scow part
Go fast
M-16 Scow tuning guide
The M-16 is tuned with mast rake, sidestay tightness (set by feel, not with a gauge), jib-lead position, traveller, board height and about 45° of mast rotation. North's guide is the only current sailmaker guide; the class association keeps an old Johnson Boat Works rigging guide and a member's heavy-air article, which disagree with North on board height in a breeze.
North Sails — M-16 Scow Tuning Guide Current web page, undated
- Written for
- North M-16 main and jib (AP mainsail on North's product page; no model named in the guide)
- Tension gauge
- None: sidestays by feel
- How it’s measured
- Rake given as a length without saying where it is measured from/to. Jib leads in inches back from the front of the cockpit (edge of the cockpit at 15+ kn).
- Source
- North Sails, Current web page, undated
Base setup
- Mast rotation
- Mainsheet blocks set for 45° of mast rotation in all wind ranges
- Crew weight
- If combined crew weight is over 290 lb, sit forward downwind in all conditions
Setup by wind
| Setting | 0–5 kn | 5–15 kn | 15+ kn |
|---|---|---|---|
| Mast rake | 24' 7" | 24' 6" | 24' 5" |
| Jib leads | 4" back from the front of the cockpit | 4 ½" back from the front of the cockpit | 5 ½" back from the edge of the cockpit |
| Traveller | Centreline | Centreline | Down to the rudder posts (18") |
| Boards | Full down | Full down | Up 2" |
| Sidestays | Just loose enough to let the mast rotate | Tight | Very tight |
| Cunningham | Leave wrinkles in the luff | Remove most wrinkles | Remove all wrinkles |
| Vang | None | Tighten once the boat is hard to hold down | Hard |
| Jib luff | Leave wrinkles for fullness | Tighten just enough to remove the wrinkles, no more | Tighten hard |
| Mast rotation (blocks) | 45° | 45° | 45° |
Trim by condition
- Main
- Top batten parallel to the boom in light air; trim harder as the wind builds.
- Jib
- Loose in light air so the top batten twists off; harder as it builds without letting the top batten hook in. Above 15 kn, play it so the bow can steer around waves.
- 0–5 kn
- Heel until the windward rudder just clears the water; crew still, smooth steering. Downwind: weight together and slightly forward; build speed, bear off, head up as it slows.
- 5–15 kn
- Flatter, windward rudder skimming (about ¾ immersed with both crew on the high side); crew together, shift back slightly in chop. Downwind: weight to windward and forward, heeling the boat to windward.
- 15+ kn
- Keep the boat on its lines so it doesn't stall in waves; crew ready on the jib sheet, skipper easing the main in puffs and trimming in lulls with the vang very tight; hike hard.
- The guide doesn't give a rake reference point, shroud tension or spreader settings.
Johnson Boat Works (builder) — Rigging and Tuning the Johnson "M" Owner's guide, late 1970s (reproduced by the class)
- Written for
- Original Johnson M-16 main and jib
- Tension gauge
- None
- How it’s measured
- Rake judged by eye from the side: spar vertical or slightly forward.
- Source
- Johnson Boat Works (builder), Owner's guide, late 1970s (reproduced by the class)
Base setup
- Sidestays
- Uppermost hole of each chainplate, same setting on each calibrated turnbuckle; tight at the dock with sails up
- Rake
- Spar vertical or slightly forward of vertical under load; ease the forestay once the jib is up so the jib carries the mast; correct the rig with the jib-halyard ball setting and sidestay tension
- Boards
- Set the check lines so the board arm sits about 1–1½" above the deck line when down
Sail controls by wind (mph)
| Control | Light 0–8 mph | Medium 8–14 mph | Heavy 15+ mph |
|---|---|---|---|
| Gooseneck | Raised: sail foot about even with or above the top of the upper white band | Lowered a notch or two | All the way down: foot even with the top of the black band |
| Outhaul | Minimal foot tension | Foot stretched further out | As far out as possible |
| Cunningham | Luff and foot tension about equal | Luff and foot tension about equal | Luff tight |
| Vang | Can be slack | Some, to stop the boom lifting in puffs | As tight as possible |
- A vintage builder guide for Johnson-built boats; it gives no jib-lead, traveller or mainsheet settings.
North American M-Scow Association (Tom Welsch) — Sailing Upwind in Heavy Air Undated (author using the system since 1985)
- Written for
- Not stated
- Tension gauge
- None
- How it’s measured
- Board height read as how much of the board horn shows above deck.
- Source
- North American M-Scow Association (Tom Welsch), Undated (author using the system since 1985)
Base setup
- Outside jib track
- For heavy air (switch at whitecaps), a second track 3¼" outboard of the inside track, or turning blocks 3¼" outboard on flush-deck boats
Trim by condition
- Rake
- Don't change it for heavy air.
- Traveller
- Centreline in heavy air (the author reports pointing about 5° higher).
- Main
- Outhaul to the black band; cunningham not too tight; vang very hard (8:1) so the boom visibly bends, eased for tacks; ease the sheet 6–12" in puffs and trim back.
- Jib
- Cars aft to open the upper leech; after a tack, trim and cleat, then two more clicks on the ratchet once the windward telltales stall.
- Boards
- Fully down, with the top 3–4" of the board horn showing.
- Disagrees with North's guide, which raises the boards 2" and drops the traveller to the rudder posts above 15 kn.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
M-16 Scow resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the M-16 Scow by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the M-16 Scow. Racing legality depends on your class or handicap rules; check them before changing equipment.
- Class associationnorthamericanmscowassociation.blogspot.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a M-16 Scow part