One-design race shop · Dinghy

Laser 4000 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Laser 4000

  • 21 verified parts
  • 8 brands

Fit verified for Laser 4000

All Laser 4000 equipment

21 parts

Can’t find a part for your Laser 4000? Request a Laser 4000 part

Go fast

Laser 4000 tuning guide

The Laser 4000 is tuned with rake (masthead to the underside of the hull at the transom), rig tension on the jib halyard, lowers and pre-bend, raking back as the wind builds. The only surviving guide is an Italian translation of the old class website guide; its tension figures use the old Loos scale, with a conversion table to the newer scale, so check which scale your gauge reads.

Laser 4000 Class (Italian association translation) — Laser 4000 tuning guide 2005 PDF (Italian translation by Carlo Annaratone of the laser4000.lasersailing.com guide)

Written for
Class one-design sails
Tension gauge
Loos, old scale (conversion to kg and the new scale given)
How it’s measured
Rake from the masthead to the underside of the hull at the transom. Rig tension (jib halyard) read just below the jib's lower batten reinforcement. Pre-bend at spreader height with the main halyard from the masthead to the boom gooseneck. Check the spreaders are symmetrical by sighting the shrouds from about 30 m away.
Source
Laser 4000 Class (Italian association translation), 2005 PDF (Italian translation by Carlo Annaratone of the laser4000.lasersailing.com guide)

Summary by wind (old Loos scale)

Wind (kn)Rake (mm)Rig tension (jib halyard)LowersPre-bend (mm)Jib car
<5 (section 0–4)736035/360 (no tension)>60 (minimum 60)As far aft as possible, moving forward as wind increases
5–10 (section 5–8)7350/736036/375Minimum (section text: 50–60)Back 3 or 4 holes
11–187320/733034/35Just touching50/60Back 3 or 4 holes
>18729035/36Just touching50/60Back 4 or 5 holes

Loos gauge conversion (as published)

Old scalekgNew scale
2610019
2810920
3011821
3213623
3415424
3617727
3820429

Trim by condition

0–4 kn
Keep flow attached: start with flat, twisted sails and slowly close the main leech; ease if the helm goes dead. Weight well forward so the transom releases cleanly. Strong rig tension pre-bends the mast to flatten the main; spreaders can go to the class maximum in the lightest air.
5–8 kn
Less mast bend for a more powerful main; no vang until you need to depower, because the leech must stay fairly open to avoid stalling. Work no more than a hand's length of mainsheet.
8–10 kn
Don't depower too early; crew calls when at full leverage, ease in gusts and re-sheet to centreline after.
11–18 kn
Flat sails with a tighter leech in flat water; more power and twist in waves or gusty wind. Get there by keeping the 5 kn settings and reducing rig tension.
Over 18 kn
Cunningham and vang hard on to control the leech; lift the board a little if the main is unmanageable. Don't over-bend the mast so the main inverts.
  • The guide's own summary table lists pre-bend in 5–10 kn as 'minimum', while the 5–8 kn section gives 50–60 mm; its wind bands also differ between the sections (0–4, 5–8, 8–10) and the summary (<5, 5–10).
  • In the light-air section the rig tension cell is printed as '35 – 36 LOOS'.
  • This is a translation; the English original is no longer online.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Laser 4000 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Laser 4000 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
We have no current one-design class rules on file for the Laser 4000. Racing legality depends on your class or handicap rules; check them before changing equipment.