One-design race shop · Dinghy
Flying Dutchman Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Flying Dutchman
All Flying Dutchman equipment
9 parts
Fit verified for Flying Dutchman
Davis Instruments
Davis Spare Vane for Windex 15
Part # dav-3151
$36.00
Fit verified for Flying Dutchman
Davis Instruments
Davis Air-Flow Tels - Set of 14
Part # dav-950
$19.99
Fit verified for Flying Dutchman
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Flying Dutchman
Schaefer
Schaefer Wind Indicator - Little Hawk Race
Part # SCHH007F00
$93.00
Fit verified for Flying Dutchman
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Flying Dutchman
Velocitek
Velocitek Prism (Digital Dinghy Compass)
Part # VELPRISM
$579.00
No Flying Dutchman parts match these filters.
Can’t find a part for your Flying Dutchman? Request a Flying Dutchman part
Go fast
Flying Dutchman tuning guide
The FD is depowered mainly by rake (eased on the genoa halyard in small steps, then moving the genoa sheet to the next clew eye) and by shroud tension used as a 'pressure valve', while the lowers keep the mast almost straight. The only public guide we found is a 2002 German-language class trim guide with no gauge readings, only centimetre steps; no sailmaker tuning chart was found online.
SFDCO (Berno Ullings), hosted by the International FD Class — FD Trim Guide (Trimmanleitung) Created 12.06.02, modified 16.06.02; based on Jan Eckert's 1992 trim guide
- Written for
- Not stated (written around an all-round genoa with several clew eyes for the sheet)
- Tension gauge
- None; settings are relative (lee shroud slack/firm) and in cm
- How it’s measured
- Rake changes are made by easing the genoa halyard in about 2 cm steps measured at the mast; board movement measured at its trailing edge.
- Source
- SFDCO (Berno Ullings), hosted by the International FD Class, Created 12.06.02, modified 16.06.02; based on Jan Eckert's 1992 trim guide
Upwind settings by wind range and power state (summary of the guide's sections; '—' = nothing given)
| Control | Light, underpowered | Light, max power to overpowered | Medium (Bft 3–4) | Strong |
|---|---|---|---|---|
| Mast / rake | Fully upright | Once fine trim is used up and the wind will hold: ease the genoa halyard about 2 cm (at the mast), then re-tighten shrouds and lowers; about 6 cm of rake per genoa eye at most, then move to the next eye | Same 2 cm steps, 6 cm maximum, then the next eye up | Further rake only as a last resort, 3–4 cm at most |
| Shrouds | Very loose in almost no wind, tightened progressively; lee shroud slightly slack with the crew fully trapezing | Tightened steadily as the wind rises, to the maximum in strong wind; ease again as it drops | Underpowered: lee shroud slack, seen swinging a little in waves; then tightened progressively with pressure | Maximum |
| Lowers | Little or none; only keep the mast near-straight | Only to hold the near-straight mast curve | Set so the mast curve is almost straight; not used to flatten the main | Very high, to stop the mast bending (adjust while stopped, vang off) |
| Genoa sheet | Leech ends about 10 cm above the deck; sheet at about 45° to the deck with slight twist; trim until the leech is roughly parallel to the centreline as wind builds | Hard, but the foot must not vibrate on the deck | — | Lead released completely to open the slot if the main flogs more and more |
| Genoa leads | Fully inboard to build pressure, then outboard once at full pressure; pulled down progressively to keep the 45° sheet angle | Keep the 45° angle (about bisecting foot and leech) | From about Bft 3 always fully down and fully out | Lowest position |
| Main | Boom on the centreline; traveller fully to windward in very light air; once the crew can just trapeze, traveller 10–15 cm to leeward and sheet the boom back to centre | Set the vang before easing so the boom swings out without rising; more vang as it builds | Underpowered: hard sheet, boom on centre, vang takes over, cunningham loose. Overpowered: main played, strong vang, cunningham until no horizontal creases | Max cunningham, max vang, foot (outhaul) max; traveller stays to windward |
| Centreboard | Fully forward and down; 2–3 cm aft in lots of waves | Lift about 5–10 cm just before a strong gust and lower again after; can stay about 10 cm up if the gust persists | Underpowered: fully down. Overpowered: about 4–5 cm aft of the forward position and raised about 10 cm | About 10 cm from the forward position and raised about 10–15 cm |
| Crew | Both as far forward as possible (crew to leeward, even on the foredeck) | Helm just behind the traveller, crew about midway between shrouds and traveller; crew moves aft in big waves and gusts | — | — |
Trim by condition
- Order of changes
- 'Fine before coarse': first sheet, vang, cunningham, shrouds and genoa leads; only then rake, lowers, board position or a different genoa eye.
- Very light air
- An exception to sailing flat: some heel reduces wetted area.
- Flat-water squalls
- As an exception, easing the lowers slightly can flatten the main when you can't change genoa eye.
- Reaching
- Ease shrouds and lowers; avoid negative (backward) mast bend from the pole by using a prebender or baby stay; in strong wind set the prebender and raise the board about 45°.
- Running
- Ease shrouds and lowers and pull the mast forward on the forestay; note your upwind marks to reset quickly.
- German-language guide summarised in our own words; it has no gauge numbers or rake lengths.
- The medium-wind section's settings boxes are partly empty in the PDF (crew, mast, genoa and genoa leads under 'underpowered'; crew and genoa under 'overpowered').
- The 'max power to overpowered' column comes from the guide's light-wind section; the guide says the medium-wind procedure is the same.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Flying Dutchman resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Flying Dutchman by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Flying Dutchman class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesFD Class Rules from 1 March 2026 (link taken from official rules page https://www.sailifdco.com/documentation/fd-class-rules-2026/; PDF itself not fetched)
- Class associationsailifdco.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Flying Dutchman part