One-design race shop · Dinghy
Interlake Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Interlake
All Interlake equipment
1 part
No Interlake parts match these filters.
Can’t find a part for your Interlake? Request a Interlake part
Go fast
Interlake tuning guide
The Interlake's simple unstayed-looking rig (no spreaders or backstay) is tuned with mast step position (76″ from the stem), rake of about 25′2″–25′4″ to the transom and shroud tension around 200–250 lb, then sailed with wire and cloth tension, jib lead, vang, bridle and centreboard angle. All guides give tension in pounds on the side stays (not the forestay) and add about 3″ to rake for boats with the old masthead crane.
Quantum Sails — Interlake Class (quick tuning guide) 2022
- Written for
- Quantum Interlake sails (Bob Sagan)
- Tension gauge
- Not named (pounds)
- How it’s measured
- Rake from full hoist to the centreline of the transom with the rig under tension; add 3″ with the old masthead crane. Jib lead from the luff-wire tack to the turning point of the jib car block under load.
- Source
- Quantum Sails, 2022
Base setup
- Mast step
- Maximum legal forward: 76″ from the stem (hull/deck intersection at the bow) to the front of the mast
- Mast rake
- 25′2″–25′3″
- Rig tension
- 240 lb; up to 280 lb+ in heavy air
- Jib cloth tension
- Wrinkles extending 5–6″ aft of the luff tape (fairly soft)
- Jib lead
- Start at 97″
- Jib foot
- Set low, preferably touching the deck
- Crew weight
- 375–475 lb; 425 lb is the sweet spot
Controls by wind
| Control | Setting |
|---|---|
| Vang | Off under 6 kn; firm enough that the boom lifts no more than 5″ in 6–10 kn; played aggressively in 10–15 kn; tight in 15+ kn |
| Main cunningham | Minimum under 10 kn; increase as wind builds to reduce overbend wrinkles; max when overpowered |
| Outhaul | 4″ of belly (about knuckle width) in 0–10 mph, then progressively flatter |
| Centreboard, beating | Straight down to 10° back (6–8″ of pull on the line) to balance helm; a bit further back in breeze/waves |
| Centreboard, off the wind | Further back reaching; half up or more running |
- Supersedes the 2015 numbers (rake 25′2″, 200 lb, lead 95″) in the older complete guide.
Quantum Sails — Interlake Complete Tuning Guide Updated 6-1-2015 by Bob Sagan (original 1998)
- Written for
- Quantum Interlake main (tapered battens), jib (separate wire and cloth), spinnaker
- Tension gauge
- Loos tension gauge (model not named), on the shrouds
- How it’s measured
- Rake: tape hoisted as high as possible on the main halyard to the middle of the back edge of the transom. Shroud tension on the trailer without sails, measured on the shrouds, not the forestay.
- Source
- Quantum Sails, Updated 6-1-2015 by Bob Sagan (original 1998)
Base setup
- Mast step
- 76″ from the stem (hull/deck intersection, excluding the rub rail) to the front of the mast
- Mast rake
- 25′2″ (add about 3″ for a dual-sheave masthead crane); adjust ±½–1″; rake forward 1″ or more in 15+ kn
- Shroud tension
- About 200 lb; ease in light air and chop; 260+ lb in strong wind
- Jib lead
- 95″ (95–6″ under load) from luff-wire tack to the car turning block, with rake at 25′2″
- Wire purchase
- Minimum 6:1, 8:1 or more better
- Boat weight
- Class minimum 650 lb
- Crew weight
- 375–475 lb (quick guide), 385–485 lb (detail section); 425 lb ideal
Trim by condition
- Jib lead
- Find the even-breaking position, then move the leads back a couple of inches; back 1–2″ to depower (also in under 3 kn); forward 1″ to power up in chop.
- Jib cloth
- Tighten until smooth, then ease until the cloth just behind the luff tape softens 3–4″ back (quick guide: up to 4+″ for max pointing); more tension in shifty winds or chop and in heavy air.
- Jib wire
- Just enough to stay fully hoisted in light air or chop; maximum in flat water or heavy air.
- Jib sheet
- Middle batten straight back; upper leech telltale always streaming.
- Vang
- Off under 10 kn; played aggressively 10–15; extremely tight 15+. In light to moderate air set so the boom lifts a couple of inches and the upper batten falls off up to 8° when eased.
- Cunningham / outhaul
- No cunningham under 12 kn; outhaul firm in most conditions, eased when the waves are bigger than the wind.
- Main
- Boom on centreline, upper batten parallel to the boom, top telltale stalled 50–70%; ease up to 10° when footing; hook up to 10° briefly to point.
- Battens
- Stiffer battens from about 13 kn, top first; thin end first.
- Centreboard
- Never forward of vertical; beating 7–10° back (about 7″ of line); 12–15° (about 1 ft) in a blow; don't pull more than 1′ up when beating. Interlakes often like 7/8 board (8–10″ of pull).
- Spinnaker
- Pole back an extra 3–4″ on a reach; halyard eased 6–8″; twings above 5 kn.
- Class-hosted copy of Quantum's older complete guide; Quantum's 2022 quick guide raises tension to 240 lb and the lead to 97″.
North Sails — Interlake Tuning Guide Undated web page (current)
- Written for
- North Interlake main, jib and spinnaker
- Tension gauge
- Loos tension gauge (model not named), pounds
- How it’s measured
- Mast butt: stem to the mast's forward edge at the imaginary hull/deck intersection (excluding the rub rail). Rake: tape on the main halyard latched at the top black band, pulled to the transom/deck joint with the rig tensioned. Bridle: deck to top of block.
- Source
- North Sails, Undated web page (current)
Base setup
- Mast butt
- Maximum forward, 76″ (6′4″)
- Mast rake
- 25′3″
- Rig tension
- Leeward shroud just goes slack upwind in about 10 mph; about 250 lb target; 200–250 lb below 8 mph; nearly 340 lb above 12 mph
- Centreboard
- Must not swing past vertical when fully down (knot the pennant if it does)
- Crew weight
- 390–460 lb combined
Traveller bridle height (deck to top of block)
| Condition | Height |
|---|---|
| Standard | 24″ |
| Light wind | 28″ |
| Very heavy wind | 18–20″ |
Trim by condition
- Jib lead
- Sheet in line with the trim line below 12 mph; 1–1.5″ aft above 12 mph.
- Jib cloth
- Remove the crow's feet at each snap; luff smooth above 10–12 mph.
- Jib sheet
- Middle batten parallel to centreline for speed; 10° outboard in light or sloppy conditions; ease for twist in breeze.
- Outhaul
- Slight horizontal wrinkle along the foot; horizontal crease in heavy wind; eased until smooth downwind.
- Cunningham
- Under 6 mph small wrinkles head to tack; medium only in the lower 1/4–1/3; heavy nearly smooth; draft about 45–50% aft.
- Mainsheet
- Upper batten parallel to the boom; 10–15° outboard in light wind or chop; drifting, parallel to centreline (boom about 2 ft/61 cm off); above 12 mph with vang about 5° outboard.
- Vang
- Heavy above 15 mph (boom may bend about 3″); downwind the vang telltale should not stall; upwind it stalls 50–75%; ease before the windward mark.
- Spinnaker
- Clews even; halyard down so the chute flies 8″ off the mast; 6–12″ luff curl; crew eases up to about 3 ft in heavy-air puffs; board up downwind, at least half down if rolling.
- Crew position
- As far forward as possible, lined up behind the shroud; move back about 1 ft in waves.
Interlake Sailing Class Association — Rigging the Interlake – Mast, and Rigging tips (Summer edition) Undated (posted May 2024; Bob Sagan, IL #628/#1442)
- Written for
- Any brand (the tips say the numbers suit most Interlakes regardless of sails)
- Tension gauge
- Not named (pounds on the side stays)
- How it’s measured
- Rake from full hoist to the centre of the rear deck / transom; add 3″ for the old masthead crane.
- Source
- Interlake Sailing Class Association, Undated (posted May 2024; Bob Sagan, IL #628/#1442)
Base setup
- Basic tuning (mast rigging notes)
- 240–260 lb on the side stays; rake 25′2–3″ to the centre of the rear deck; less tension in light air, more in a big breeze
- Rigging tips (summer edition)
- Rake 25′3″ to 25′4″ with 230 lb side-stay tension
- Gooseneck
- Boom track 22″ (±½″) above deck; racing bands 21″ apart (inside edges), lowest band 22″ (±½″) above deck
- Standing rigging
- 1/8″ stainless for side stays and forestay
- Spinnaker hoist
- Maximum 18′6″ above deck
- Two class-hosted notes by the same author give slightly different base numbers; the summer tips are at https://interlakesailing.org/wp-content/uploads/2024/05/Rigging-Summer-tips.pdf
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Interlake resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Interlake by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Interlake class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesSpecifications page, no version; item amended 5/20/2013; plans at /resources/plans/
- Class associationinterlakesailing.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Interlake part