One-design race shop · Keelboat

Catalina 22 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Catalina 22

  • 40 verified parts
  • 7 brands
  • Fit checked Nov 2026

Fit verified for Catalina 22

All Catalina 22 equipment

40 parts

Can’t find a part for your Catalina 22? Request a Catalina 22 part

Go fast

Catalina 22 tuning guide

The Catalina 22 is tuned for rake first, then upper, forward-lower and aft-lower shroud tension on a Loos Model A gauge, with the backstay controlling headstay sag on the water. The two published guides use the same gauge but very different numbers (North 28/24/24, Harper 25/15/10) and different rake methods, and there are many hull, keel and mast variants, so treat both as starting points.

North Sails — Catalina 22 Tuning Guide Web page (posted 2017)

Written for
North main and genoa (no models named)
Tension gauge
Loos Model A
How it’s measured
Rake with the boat floating on its lines: hang a weight on the main halyard with the shackle 12″ below the boom, and measure from the aft face of the mast to where the halyard crosses the boom. Centre the mast with a tape hoisted on the halyard after snugging the backstay.
Source
North Sails, Web page (posted 2017)

Base setup

Rake
8″ for fixed keels; 6–7″ for swing keels (set with the headstay turnbuckle)
Uppers
28 on the Model A
Forward lowers
24
Aft lowers
24
Mast
Straight fore and aft, with a little rake for upwind bite; re-check side-to-side straightness under sail with moderate backstay
Deck set-up
Inboard genoa tracks 2–3′ long, centred on the aft edge of the cabin, 2″ out from the deck/cabin joint; 36″ rollers on the forward lowers and 12″ rollers on the uppers; an easily adjusted, fairly powerful backstay

Trim by condition

Main, light (0–8 kn)
Clew 1–2″ in from the band; cunningham/halyard loose enough to show horizontal wrinkles; traveller centred or slightly to windward; sheet so the top telltale flies about 90% of the time and the top batten is slightly outboard of parallel to the boom.
Genoa, light
Halyard just showing a hint of luff wrinkles; lead about 30″ forward of the deck drain, adjusted so the luff breaks evenly (forward if the top breaks first, back if the bottom does); backstay for about 6″ of forestay sag; sail 4–6″ off the spreader end.
Main, moderate
Foot out to the band, traveller centred, top telltale flying about 70% of the time, top batten parallel or slightly inboard; just enough cunningham to remove wrinkles.
Genoa, moderate
Sail 2–3″ off the spreader end; medium backstay for 3–4″ of sag; in chop move the lead forward 1–2 holes.
Main, heavy
Outhaul max; halyard/cunningham hard; aft lowers tensioned to limit bend; backstay very tight; top batten outside parallel; traveller fully down; vang tight enough to vang-sheet; play the sheet hard in puffs.
Genoa, heavy
Halyard quite tight; lead 1–2 holes aft of the light-air position; sail 3–4″ off the spreader end; backstay very tight to straighten the headstay.
  • Settings are starting points; North suggests keeping a log of fast settings. No spinnaker section.

Pete Harper — C22 Tuning Guide 2006 (PDF created July 2006)

Written for
Main, genoa, class jib, spinnaker
Tension gauge
Loos Model A
How it’s measured
Written for the old hull style with a swing keel and the new mast section. Centre with a 50′ tape on the main halyard to the same toe-rail point each side (lowers loose). Rake: with the boom in place and just enough backstay to take the slack out of the forestay, measure from the masthead (including the halyard shackle) to the outboard edge of the rudder cut-out in the transom. Prebend: main halyard pulled tight from masthead to gooseneck, measured at the spreaders.
Source
Pete Harper, 2006 (PDF created July 2006)

Base setup

Rake
29′ 4″ masthead to transom (as above)
Uppers
25 (tensioned equally once the mast is centred)
Forward lowers
15, mast in column side to side
Aft lowers
10
Prebend
½–1″ at the spreaders; the old mast needs less forward-lower tension for the same bend
Deck
Reinforcing the lower-shroud attachment (supports to the bulkhead) is strongly recommended

Shroud tension by wind (Loos Model A)

WindUppersForward lowersAft lowers
Light2515 (or base)10 (or base)
Medium2517 (or base +2)10 (or base)
Heavy30 (base +5)20 (base +5)10 (or base)

Trim by condition

Headstay sag
Measured halfway up the genoa luff to a spare halyard pulled from masthead to tack: 6–8″ in light air (0–7 kn) with the backstay eased; 3–4″ in medium (8–15); as little as possible in heavy (15+).
Light (0–7 kn)
Traveller to windward, boom on centreline, second batten from the top parallel to the boom; cunningham eased to speed wrinkles; outhaul eased to fill the shelf foot; no vang – sheet until the top leech telltales curl, then ease until they just fly. Genoa lead about level with the back of the windows, foot over the deck edge at mid-point, leech 4–6″ off the spreader tip; halyard just removing horizontal wrinkles; about 6″ of sag.
Medium (8–15)
Traveller centred; vang controls leech tension; outhaul for power (fold the shelf if overpowered); cunningham removes luff wrinkles; backstay to remove as much sag as possible without over-depowering.
Heavy (15+)
Traveller centred and vang sheeting; play the mainsheet to control heel; cunningham and outhaul hard; backstay opens the leech and tightens the headstay; move the genoa block back one notch if still overpowered.
Spinnaker
Keep the clews level (pole low in light air, higher as it builds); pole perpendicular to the wind on broad reaches and runs; keep a slight curl. Drop the genoa with the spinnaker up; the class jib may stay up when reaching.
Turns
Count turns at the dock from base to each setting so changes can be repeated on the water.
  • A personal guide, not a sailmaker's. Its base tensions are much lower than North's on the same Model A gauge.
  • Hosted on the sailboatowners.com Catalina knowledge base.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Catalina 22 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Catalina 22 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Catalina 22 class rules before changing equipment, and ask your class measurer if a part is not original equipment.