One-design race shop · Dinghy
Jet 14 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Jet 14
All Jet 14 equipment
11 parts
Fit verified for Jet 14
Davis Instruments
Davis Black Max Wind Direction Indicator
Part # dav-1295
$69.99
Fit verified for Jet 14
TRAC Outdoors
TRAC Outdoors Anchor Rope - 3/16" x 100' w/SS Shackle
Part # tra-69080
$30.99
No Jet 14 parts match these filters.
Can’t find a part for your Jet 14? Request a Jet 14 part
Go fast
Jet 14 tuning guide
Jet 14 tuning is set mostly ashore: spreader length (about 17¼″), mast butt (about 19⅜–19½″ from the centreboard pin), rake (about 20′8″–20′9″) and shroud tension (80–200 lb by wind in North's guide, 140–180 lb in the class speed guide), with jib leads about 80–82″ aft and 29–36″ apart. The guides give tension in pounds; the class guide warns Loos gauges vary from one to another.
North Sails — Jet 14 Tuning Guide Undated web page (compiled with help from national champions; thanks Brent Barbehenn)
- Written for
- North Jet 14 main, jib and spinnaker
- Tension gauge
- Not named; tension in pounds set on the jib halyard and measured on the shrouds
- How it’s measured
- Spreader length from the side of the mast to the shroud/spreader intersection; tip-to-tip shroud to shroud. Mast butt from the centreboard pin to the middle of the mast. Rake from the main halyard (locked at the top band) to the top of the transom.
- Source
- North Sails, Undated web page (compiled with help from national champions; thanks Brent Barbehenn)
Base setup
- Spreader length
- 17 1/4″ for most boats
- Spreader tip-to-tip
- About 32″; wider for heavier crews, narrower for lighter
- Spreader angle
- Heavier crews deflect the shroud slightly forward (1/4–1/2″); lighter crews aft (1/4″)
- Mast butt
- 19 3/8″ starting point; forward reduces prebend, aft induces it
- Shroud attachment
- About 72″ aft of the jib tack
- Prebend
- About 1/2–3/4″ positive at the medium-wind setting; mast straight sideways
- Jib leads
- Start on the clew trim line; about 82″ from tack to the sheet bearing point; about 32″ apart (some as close as 29″)
Rig tension and rake by wind (pounds on the shrouds)
| Wind (mph) | Rig tension | Rake |
|---|---|---|
| Below 5 | 80 lb | Not given |
| 5–10 | 150 lb | About 20′8″ |
| 10–15 | 180 lb | About 20′8½″ |
| 15+ | 200 lb | Not given |
Trim by condition
- Mainsheet
- Top batten parallel to the boom; top telltale flying about 70% under 7 kn, constantly above 10–12 kn.
- Cunningham
- Light wind 6–8″ wrinkles; then only the lower quarter; nearly smooth above 18 mph.
- Outhaul
- Tight upwind except the lightest air (shelf foot about 1″ open mid-boom); downwind ease 2–3″ (shelf 3–4″ open).
- Vang
- Slack until overpowered, then progressively on so the sheet works like a traveller; ease substantially before the weather mark.
- Traveller
- Drop when overpowered until helm is neutral and the boat flat.
- Jib
- Trim until the leech telltale is just on the verge of stalling; move the lead forward if the top luffs first, back if the bottom does; up to 2″ aft in heavy wind. Slight luff wrinkles, smooth in heavy wind.
- Spinnaker
- 6–12″ luff curl; pole nearly perpendicular to the wind (telltale about 1 ft up the topping lift); pole height keeps clews even.
- Wind bands for tension are in mph, but the mainsheet notes use knots.
- The same text is hosted by the class as 'Jet-14 Set Up and Tuning (Greg Fisher)': https://www.jet14.com/?view=article&id=40:jet-14-set-up-and-tuning-greg-fisher&catid=21
Jet 14 Class Association — Jet-14 Speed Guide 2002 (Dirk Schwenk and contributors)
- Written for
- Not brand-specific (mentions 1997 UK and 2000 Doyle cuts)
- Tension gauge
- Loos gauge (model not named); the guide warns Loos gauges vary, so treat numbers as rough
- How it’s measured
- Rake: tape on the main halyard raised to the black band, measured to the top of the middle of the transom (¼″ changes are noticeable). Prebend halfway up, sighting the luff track. Mast butt from the centre of the centreboard pin to the centre of the mast. Spreader length from the mast face to the spreader/sidestay junction. Jib leads measured between the sheet turning points and aft from the stem.
- Source
- Jet 14 Class Association, 2002 (Dirk Schwenk and contributors)
Base setup
- Mast section
- DM-1 (DM-2 and wood occasionally fast); keel-stepped
- Rake
- 20′9″ ±1″; competitive range about 20′8½″ to 20′9¾″
- Prebend
- Under 1″; competitive boats ¼–¾″
- Mast butt
- 19½″ ±½″ (historically 19–19½″, some up to 20¾″)
- Spreader length
- 17¼″ ±½″; competitive 16¾–18″; sweep neutral
- Sidestay tension
- 140–180 lb, more in heavier air (adjusted via the jib halyard)
- Jib leads
- 33″ ±3″ apart (competitive 31–36″); 80″ ±5″ aft of the stem (text also says generally 80–90″)
- Crew weight
- 270–330 lb combined (top four at the 2000 Nationals about 250–350 lb)
2000 Nationals top finishers – mast tuning (tension in pounds)
| Place | Skipper | Hull | Rake | Prebend | Butt | Spreader | Rig tension |
|---|---|---|---|---|---|---|---|
| 1 | Barbehenn | 698 | 20′8½″ | ¾″ | 19⅜″ | 17¼″ | 180 |
| 2 | Koski | 1135 | 20′9¾″ | ½″ | 19⅜″ | 17¼″ | 130 |
| 3 | Zaugg (1999) | 1132 | 20′8¾″ | ½″ | 19″ | 17¼″ | ---- |
| 4 | Schwenk | 398 | 20′8¾″ | ¼″ | 19⅜″ | 17¾″ | 70 |
| 6 | Bruns | 1126 | 20′8″ | ½″ | 19½″ | 17⅜″ | 100 |
| 7 | Hansen, D | 1066 | 20′9½″ | ¾″ | 20″ | 16¾″ | 150 |
| 8 | Simonds | 1137 | 20′9½″ | ½″ | 19⅜″ | 17¼″ | 130 |
| 9 | Parramore | 1140 | 20′9¾″ | ½″ | 19⅝″ | 18″ | 140 |
Trim by condition
- Jib leads
- Top and bottom telltales should break together in medium conditions.
- Centreboard
- Vertical and tight in the trunk (shims limited by class rules).
- Trim and heel
- Bow knuckle 1–2″ in the water, transom just skimming; flat to slight heel with near-neutral helm.
- Mainsheet / vang / outhaul
- Light air: boom to the transom corner with little downward pull, vang eased, outhaul taut; in breeze add sheet and vang to hold the leech; boom carried above horizontal in most conditions.
- Internal inconsistencies: the base tension (140–180 lb) doesn't cover the 70 and 100 lb in the Nationals table; the text quotes 140 lb for hull 1135 where the table shows 130; the lead text says 80–90″ against the 80″ ±5″ base.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Jet 14 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Jet 14 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Jet 14 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesTechnical Specifications page, no version stated
- Class associationjet14.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Jet 14 part