One-design race shop · Keelboat

Cape 31 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Cape 31

  • 87 verified parts
  • 7 brands
  • Fit checked Nov 2026

Fit verified for Cape 31

All Cape 31 equipment

87 parts

Can’t find a part for your Cape 31? Request a Cape 31 part

Go fast

Cape 31 tuning guide

The Cape 31 is set up from an 11–12 kn base with mast rake, heel position and deck chocks fixed at the dock, then V1, D1, D2 and forestay turns plus deck-chock changes by wind speed, with runners and jib car height doing much of the on-the-water work. North's matrix is written for its 3Di sails and reads the V1s on a Loos PT-3M but the D1s and D2s on a PT-2M.

North Sails — Cape 31 Tuning Guide December 2023

Written for
North 3Di: MNi-6 all-purpose main; Helix jibs J1 (J1-4), J2 (J2-2), J3 (J3-4), J4 heavy-weather OSR (J4-3); A1.5 (A1.5-2), A2 Minus (A2 Minus-1), A2 (A2-2 Poly), A3 (A3-2), A4 (A4-3)
Tension gauge
Loos PT-3M for the V1 shrouds; Loos PT-2M for the D1 lowers and D2 uppers
How it’s measured
Rake: mark the jib halyard level with the top of the gooseneck measurement band, swing it to the forestay and mark it, then measure from that mark to the middle of the forestay (load-sensor/tack) pin. Prebend: pull the most forward main halyard to the back corner of the lowest bit of mast track above the gooseneck and measure the gap at the lowest spreaders, on base with base chocks, runners loose and boom down. Each turn in the matrix is 360°.
Source
North Sails, December 2023

Base setup

Mast heel
135–145 mm from the aft edge of the mast to the centre of the front keel bolt; move aft for more prebend, forward for less
Mast rake
1,715 mm (forestay mark to forestay pin)
Deck chocks
Light pressure on the front chocks: 4–8 mm of positive chock (fill the gap in front of the mast plus 4–8 mm). Check there is still a little prebend on +1 chocks. Chocks strongly affect D1 tension.
Prebend
40–50 mm
Centring
Shrouds near base with D1s (and D2s) loose; swing the jib halyard between shroud bases to centre the hounds, then re-tension the diagonals and straighten the mast
Base tensions
V1 20 (PT-3M), D1 35 (PT-2M), D2 25–27 (PT-2M) at 11–12 kn
Spreader marks
Underside of each spreader: one in the centre and one each 150 mm inboard and outboard of it

Tuning matrix (turns from base; tensions in brackets – V1 on PT-3M, D1/D2 on PT-2M)

TWS (kn)V1 shroudsD1 lowersD2 uppersForestayDeck chocks
4–7Base −2Base −3Base −2Base −8Base +1
8–9Base −1Base −2Base −1Base −4Base
10–11BaseBase −1BaseBase −2Base
11–12 (base)Base (20)Base (35)Base (25–27)BaseBase
12–14BaseBase +1BaseBase +2Base
14–16Base +1Base +1BaseBase +4Base
16–18Base +2Base +1BaseBase +6Base
18+Base +3Base +2 (37)BaseBase +8Base −1

Sail crossovers

SailWind (kn)
J1 (J1-4)5–11
J2 (J2-2)10–16
J3 (J3-4)15–21
J4 heavy weather OSR (J4-3)20+
A1.5 (A1.5-2)5–9
A2 Minus (A2 Minus-1)8–12
A2 (A2-2 Poly)11–21
A4 (A4-3)21+
A3 (A3-2)Reaching

Trim by condition

Jib cars
Max inboard in light and medium air; one step outboard when out of range or at the very top of a jib's range. Car height (control by the main hatch) is the main tool for depth and twist.
Jib halyard
Helix jibs: use the halyard fine-tune to control camber and luff sag.
Traveller
All the way up in light air for height and power. In strong wind stay near centreline and twist the main with the fine-tune; once overpowered, just above centreline is fastest. Easing the traveller is one of the first depowering moves.
Runners
Off below 6 kn, then progressively tighter up to a maximum combined headstay/tack load of 1.8 tonnes (the builder's limit). Downwind, loosen for depth but keep the windward runner snug, tightening with wind just enough to keep the headstay straight.
Outhaul
Just loose enough that the sail doesn't touch the boom below base; tighten as the wind builds.
Cunningham
Off downwind and in light air; progressively tighter as the wind builds, especially at or above +4 on the headstay.
Downwind
In light air the kite flies and gybes best with the jib down; above about 8 kn TWS sail VMG angles and leave the jib up.
Battens
Carbon full-length battens of a couple of stiffnesses in the head of the main (and jib) to suit the wind range.
  • On the web page the 16–18 and 18+ rows share one table row; we have split them in order (V1 +2/+3, D1 +1/+2 (37), D2 Base/Base, forestay +6/+8, chocks Base/−1).
  • The labels follow North's: D1 = 'lowers', D2 = 'uppers'.
  • The full PDF tuning guide is offered via a crossover-chart link to an Adobe viewer, which we didn't open.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Cape 31 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Cape 31 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Cape 31 class rules before changing equipment, and ask your class measurer if a part is not original equipment.