One-design race shop · Dinghy
2000 (Laser 2000) Race Shop
Everything you need to prepare, compete, and win.
Fit verified for 2000 (Laser 2000)
All 2000 (Laser 2000) equipment
25 parts
Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for 2000 (Laser 2000)
Harken
Harken Block - Carbo 57mm Single - Ratchet (Red)
Part # HAR2135RED
$90.95
$103.15Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for 2000 (Laser 2000)
Rooster
Rooster Pro Plus Padded Toestrap Set for Laser 2000 Helm
Part # ROO131304
$60.30
$67.00Fit verified for 2000 (Laser 2000)
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for 2000 (Laser 2000)
Harken
Harken Block - Carbo 40mm Single - Ratchet - Swivel / Becket (Black)
Part # HAR2609
$78.95
$90.00Fit verified for 2000 (Laser 2000)
Rooster
Rooster Pro Plus Padded Toestrap Set for Laser 2000 Crew
Part # ROO131303
$48.60
$54.00Fit verified for 2000 (Laser 2000)
Harken
Harken Block - Carbo 40mm Single - Ratchet - Swivel (Black)
Part # HAR2608
$72.95
$83.10Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for 2000 (Laser 2000)
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for 2000 (Laser 2000)
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for 2000 (Laser 2000)
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for 2000 (Laser 2000)
Davis Instruments
Davis Air-Flow Tels - Set of 14
Part # dav-950
$19.99
Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for 2000 (Laser 2000)
Schaefer
Schaefer Wind Indicator - Little Hawk Race
Part # SCHH007F00
$93.00
Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan Series 40 RTA OrbitBlock,Auto, Single, Swivel Head
Part # RONRF46100
$77.33
$90.98Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for 2000 (Laser 2000)
Velocitek
Velocitek Prism (Digital Dinghy Compass)
Part # VELPRISM
$579.00
Fit verified for 2000 (Laser 2000)
Schaefer
Schaefer Wind Indicator - Little Hawk MK 1
Part # SCHH003F00
$34.70
Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for 2000 (Laser 2000)
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No 2000 (Laser 2000) parts match these filters.
Can’t find a part for your 2000 (Laser 2000)? Request a 2000 (Laser 2000) part
Go fast
2000 (Laser 2000) tuning guide
The 2000 (formerly Laser 2000, now built by RS Sailing) is tuned mainly with mast rake, shroud tension and spreader length and deflection; no full class tuning guide is published openly, so the numbers here come from class newcomer notes, a sailmaker's blog and the builder's rigging guide. Rake datums differ (top of the rudder post vs the top rudder gudgeon), so compare like with like. This is not the Laser 2, a different, older trapeze dinghy.
2000 Class Association — 2000 Class Newcomers Top Tips – tuning Byline 22 Jan 2021 (page published May 2023)
- Written for
- Not stated; Simon Horsfield's own settings, used for more than ten years (article by Simon Horsfield and Katie Burridge)
- Tension gauge
- Loos gauge, 3 mm wire scale, read on the port shroud
- How it’s measured
- Hoist a tape on the main halyard tight to the masthead; check the datum to the gooseneck (close to 5220 mm), then swing aft to the top of the rudder post. Jib up and rig tension set (24 on the Loos gauge) before measuring rake. Mast heel is measured from the back of the mast to the back of the rudder post.
- Source
- 2000 Class Association, Byline 22 Jan 2021 (page published May 2023)
Base setup
- Spreader length
- 860 mm tip to tip
- Spreader deflection
- 170 mm
- Mast heel
- 2720 mm from the back of the mast to the back of the rudder post
- Rig tension
- About 150 kg (330 lb), which reads 24 on the Loos 3 mm scale
- Rake datum
- Halyard to the gooseneck should read close to 5220 mm
- Mast rake
- 6560 mm to the top of the rudder post
- Shroud pin effect
- One hole up or down changes rake by about 40 mm; a diagonal move about 20 mm. Re-set tension to 24 on the Loos gauge after every pin change.
Centreboard downwind, by sailing mode
| Wind | Centreboard |
|---|---|
| Displacement (about 10 kn or less) | Consider raising it slightly so the boat can slide to leeward (less stable) |
| Semi-apparent (11–16 kn) | Half up |
| Full apparent (17–30 kn) | Keep it down |
Trim by condition
- Sheeting
- Ashore, see how much 1, 2 or 3 inches of sheet in or out changes sail shape; when the wind drops, easing the jib by as little as one fleck can stop the boat stalling.
- Kicker
- In strong winds have enough on to let you hike and play the mainsheet; no numbers given.
- Rake here is measured to the top of the rudder post, not to the top gudgeon used in the Rooster posts.
- The page shows the article was published on 21 May 2023 with a byline dated 22 Jan 2021.
Rooster Sailing — 2000 Tuning Guide and New 2000 Shake Down and Sort (Steve's Blog) Both posts dated 15 March 2021
- Written for
- Not stated; written from a 2000 Nationals-winning programme
- Tension gauge
- Not stated (shroud tension given in lb)
- How it’s measured
- Rake from the masthead to the top of the aft (top) rudder gudgeon. The shake-down post quotes a fleet figure taken from the main halyard fully hoisted to the top of the plastic on the top rudder gudgeon where it meets the hull.
- Source
- Rooster Sailing, Both posts dated 15 March 2021
Base setup
- Mast rake (main post)
- 6570 mm to the top of the aft top gudgeon
- Shroud tension
- 150 lb
- Rake (shake-down post)
- Set at 6560 mm 'as per the tuning guide'; sailed at about 6535 mm before the shake-down; some fleet boats go as far forward as 6580 mm
- Rake adjustment
- Half a pin of extra rake is about 25 mm at the same rig tension
- Mast foot
- One hole forward of the most aft hole
- Spreaders (new Selden mast)
- Deflection settled from about 175–180 mm to a final 165 mm; length about 475 mm, final 480 mm
Trim by condition
- Spreader approaches
- Three fleet set-ups: old Holt Allen mast with spreaders out and forward of neutral and rig raked forward for downwind pace; Selden with neutral spreaders (pushed out for more power) for more rig tension; Selden with no deflection, neutral fore-and-aft and out, allowing high tension with gust response.
- Jib
- Always use the most aft car position; a 2:1 sheet helps in a breeze.
- Gennaker
- Tack line and head can each be eased up to 5″ in light air (head about 2″ in strong wind); heel to windward to pull the kite clear of the main.
- Centreboard
- Rig the handle with thin line so the board can swing forward until it is nearly flush with the top of the case (don't force it further), giving some weather helm downwind; in light air with both sailors well forward it can come almost fully up.
- Downwind trim
- Stay forward to use the flat hull sections; in light air sit far forward with windward heel.
- New mast
- Rig tension dropped by about a third overnight as a new mast settled; re-check.
- The second post is at https://www.roostersailing.com/blogs/tuning-guide/new-2000-shake-sort.
- The two posts give slightly different rake figures (6570 vs 6560 mm), and the rake datum differs from the class article.
- The post's 'tuning guide' (6560 mm) is not linked; no public copy was found.
RS Sailing / LDC (builder) — LDC 2000 Rigging Guide v.2 v.2 (PDF created Aug 2014; Selden vernier spreader sheet dated 01.07.14)
- Written for
- Not stated (builder's rigging guide for the LDC 2000)
- Tension gauge
- Loos gauge (printed 'Loose Gauge'; units, no model)
- How it’s measured
- Rig tension is pulled on through the jib (the forestay must stay slack); if a Loos gauge is used, the reading is taken 0.75 m above the shroud vernier adjuster.
- Source
- RS Sailing / LDC (builder), v.2 (PDF created Aug 2014; Selden vernier spreader sheet dated 01.07.14)
Base setup
- Spreaders (Selden vernier table, LDC 2000)
- Primary pin aft, adjuster 1A, end cap aft, 3.0 mm wire slot, 0 holes visible
- Shroud verniers when stepping
- Pin in the 3rd hole down on the back of the vernier
- Rig tension
- Shrouds firm to the touch; if a Loos gauge is available do not exceed 24 units or 150 kg
- Forestay
- Never sail with tension on the forestay; it only holds the mast up in the dinghy park
- The builder says these are starting settings for general sailing and refers racers to the class association.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the 2000 (Laser 2000)
Technical
2000 (Laser 2000) resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the 2000 (Laser 2000) by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current 2000 (Laser 2000) class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rules2000 Class Measurement Rules, v4.4 per class site technical update 31 Aug 2026 (v4.3 published 11 Apr 2026); version not shown on rules page itself
- Class association2000class.org
- Builder specifications2000 (Laser 2000) on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a 2000 (Laser 2000) part