One-design race shop · Multihull
Hobie Wave Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Hobie Wave
All Hobie Wave equipment
7 parts
Fit verified for Hobie Wave
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Hobie Wave
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for Hobie Wave
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Hobie Wave parts match these filters.
Can’t find a part for your Hobie Wave? Request a Hobie Wave part
Go fast
Hobie Wave tuning guide
The Hobie Wave is a simple unirig cat, so tuning means squaring the platform, setting rudder alignment, choosing a loose or tighter rig by shroud pin position, and setting mast rake on the forestay adjuster, which matters most. The one published guide (Bob Curry, 2022) measures rake as a length from the masthead to the rear-beam eyestrap and adjusts it for sailor weight; there is no tension-gauge setting.
Bob Curry (TheBeachcats.com) — The Hobie Wave Tuning Guide December 2022 (posted February 2025)
- Written for
- HCA Wave factory sail and Formula Wave mylar sail (both about 38% draft position)
- Tension gauge
- None (rig tension judged by shroud pin position)
- How it’s measured
- Square: bow-to-bow at the centre of the forward screws vs transom-to-transom at the middle of the bottom pins. Rudder toe: 12″ below the lower castings, leading edges vs trailing edges. Rake: tape run to the masthead and secured on the mast horn cleat, measured to the top of the eyestrap on the rear beam.
- Source
- Bob Curry (TheBeachcats.com), December 2022 (posted February 2025)
Base setup
- Platform square
- Bow and transom measurements equal; slight toe-in acceptable, but shim the front beam stops if the difference exceeds ¼″ (5 mm)
- Rudder toe
- Zero: leading-edge and trailing-edge measurements equal
- Shrouds
- Earlier boats 13′11″, newer boats 13′8″; the shorter shrouds allow more rig-tension range. Loose or tighter rig is personal choice (flat water often looser, lumpy water tighter); the guide's photos show the 'optimal loose rig' pin positions for each shroud length
- Mast rake
- 19′10″ masthead to rear-beam eyestrap as an all-round start (author 160 lb); lighter sailors nearer 19′8″ (more rake), heavier nearer 20′ (less rake); heavier sailors may stand the rig forward a hole or two on the forestay
- Mainsheet
- 4:1 maximum purchase; author uses a Harken 40 mm ratchet (on all the time) with a 40 mm double on top; 7 mm sheet when windy, otherwise 6 mm, or 5 mm with a 29 mm double block in really light air
Trim by condition
- Rake
- The biggest performance factor; choose between a more upright rig for power and maximum rake short of two-blocking the mainsheet, trading pointing against footing.
- Sail shape
- Draft about 38% on both sail types; the HCA sail's battens were tapered (belt sander) and the Formula sail uses RBS tapered battens.
- The web post and its PDF (https://thebeachcats.com/files-archive/hobie-wave-tuning/Hobie-Wave-Tuning-Guide-2022-Bob-Curry.pdf) carry the same text and numbers.
- Shroud pin positions are shown only in photos, not as hole numbers.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Hobie Wave resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Hobie Wave by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Hobie Wave class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesIHCA 2025-2028 Class Rules, revised 1 March 2026
- Class associationhobieclass.com
- Builder specificationsHobie Wave on hobie.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Hobie Wave part