One-design race shop · Dinghy
Comet Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Comet
All Comet equipment
10 parts
Fit verified for Comet
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR468
$36.95
$41.50Fit verified for Comet
Harken
Harken Traveler Car 7/8 in (22.0 mm) - Pivoting Shackle
Part # HAR2727
$209.95
$238.65Fit verified for Comet
Harken
Harken Swivel Cam Cleat - Base (Small) w/ Cam-Matic 150 - Line: 1/4 to 5/8 in (6 to 16 mm)
Part # HAR205
$163.95
$186.05Fit verified for Comet
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80
No Comet parts match these filters.
Can’t find a part for your Comet? Request a Comet part
Official Harken dealer
Comet deck layout
- Length
- 16 ft (4.877 m)
- Beam
- 5 ft (1.524 m)
- Weight
- 265 lb (120.202 kg)
- Main
- 140 sq ft (13.001 sq m)
- Crew
- 2
Vang
-
1
40mm BlockHarken 2650
$31.95 -
3
Standard Low Profile Cam Base — SwivelHarken 205
$163.95 -
4
29mm Double Block — SwivelHarken 342
$53.95 -
6
22mm Cheek BlockHarken 233
$19.95 -
9
29mm BlockHarken 348
$17.95 -
10
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
16
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
20
22mm Car — Pivoting ShackleHarken 2727
$209.95 -
24
40mm T2™ Loop Soft-Attach BlockHarken 2148
$51.95 -
25
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
27
40mm Cheek BlockHarken 2644
$36.95 -
28
Micro Cam-Matic® CleatHarken 468
$36.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Comet tuning guide
The 16-foot Comet is set up with centreboard pin position, rake (about 21′10″ to the top of the transom) and 200+ lb of stay tension, then mast bend is controlled with deck blocks (or a mast bender) and vang as the wind builds. Only one published guide was found, Beaton Sails', and it gives tension in pounds without naming a gauge; Comet rigs vary a lot from boat to boat.
Beaton Sails — Beaton Sails – Comet Tuning Guide Undated
- Written for
- Beaton Comet mainsail (designed with a fair amount of luff curve) and jib
- Tension gauge
- Not named (pounds)
- How it’s measured
- Rake from the top of the mast to the top of the transom. Centreboard pin measured to the back of the mast. Mast bend controlled with blocks at deck level against reference marks from the neutral position (mast under stay tension with blocks out or bender loose).
- Source
- Beaton Sails, Undated
Base setup
- Centreboard
- Pin to back of mast 19 3/4″
- Mast rake
- 21′10″ (top of mast to top of transom)
- Stay tension
- 200+ lb
- Jib leads
- Light air 70″, heavy air 71″; 12″ off the centreline
- Jib foot
- Right down on the deck
Mast blocking (prebend from neutral)
| Condition | Blocking | Notes |
|---|---|---|
| Light air | Block forward 7/8″ from neutral | Smooths and flattens the front of the main, frees the leech, softens the forestay for a fuller jib (Rich Warren also eases rake a little) |
| Crew on the windward side | About 1/2″ of prebend | Start using the vang to bend the mast higher up (Warren returns rake to his original spot) |
| Overpowered | Blocks removed in front so the mast can go within 3/4″ of the front of the partner | Vang until under control and ease it in lulls |
Trim by condition
- Forestay sag in breeze
- With a traveller, drop the car to balance the helm and trim hard; with a split mainsheet, tighten the shrouds to straighten the forestay.
- Short two-page guide; the writer isn't named beyond Beaton Sails.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Comet resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Comet by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Comet. Racing legality depends on your class or handicap rules; check them before changing equipment.