One-design race shop · Keelboat

RS21 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

RS21

  • 57 verified parts
  • 13 brands
  • Fit checked Nov 2026

Fit verified for RS21

All RS21 equipment

57 parts

Can’t find a part for your RS21? Request a RS21 part

Go fast

RS21 tuning guide

The RS21 is tuned with cap shrouds and lowers in full turns from an 8–10 or 7–11 kn base, a 9550 mm rake (masthead to the top back edge of the transom) and a backstay that is played constantly in light and medium air. The two published charts use different tension scales: RS Sailing's rigging manual quotes a Spinlock Rig Sense gauge (200–475 on the caps), while the West Coast Sailing chart on RS Sailing's site gives much smaller numbers (19/12 at base) without naming the gauge, so the readings can't be compared.

RS Sailing / West Coast Sailing — RS21 Tuning Guide (created by Jake Sorosky, West Coast Sailing) 29 April 2019

Written for
Not stated (RS21 class sails)
Tension gauge
Not stated
How it’s measured
Full turns on the adjusters from base (8–10 kn). Rake given in mm (9550 at base); the rigging manual measures it from the masthead to the top back edge of the transom above the rudder gudgeon.
Source
RS Sailing / West Coast Sailing, 29 April 2019

Base setup

Base wind
8–10 kn
Cap shrouds (base)
Tension 19 (gauge not stated)
Lowers (base)
Tension 12 (gauge not stated)
Rake
9550
Jib car
1
Tack height
2in

Tuning by breeze (full turns from base; tensions as printed, gauge not stated)

Breeze (kn)HSCap shroud (turns)Cap tensionLowers (turns)Lowers tensionRakeJib carTack heightVang
0–50−1.5−1.512.5inSnug to max ease
5–80−1−1.512.5inSnug to max ease
8–10 (base)0019012955012inSnug to max ease
10–1421021.5inSnug
14–1842121 inSnug +
18–2263271.5183BottomTight
22+73.51.53BottomTight

Trim by condition

Backstay
The key speed control: almost a full-time job in light–moderate air (trimmers play it, driver trims main); less adjustment once it's windy, when vang and mainsheet matter more.
Light air
Lots of twist and power; keep the relative sheet tension between main and jib right. Weight forward with slight heel upwind. Downwind, drop the jib for manoeuvres; late boom gybes.
Medium air
Play the backstay for power through the wind changes; move body weight in and out. Find the crossover point for furling the jib downwind.
Medium–heavy
Vang sheeting; set main shape with vang and cunningham, power with the backstay. Downwind pick a target speed rather than chasing the plane.
Breeze on
Vang-sheet hard, ease the jib a little in puffs. Downwind stay on the plane but keep going down; weight back in puffs and forward in lulls.
  • The 'HS' column isn't defined on the page; its values (0 to 7 turns rising with wind) suggest headstay turns from base.
  • Tension numbers are given only for the base and 18–22 kn rows, and the gauge isn't named; they are on a different scale from the Rig Sense numbers in RS Sailing's rigging manual.

RS Sailing (rigging manual) — RS21 Rigging Manual V16 – 4.8 Rough Rig Setting Rigging Manual V16

Written for
RS21 race sails (main 16.2 m², jib 8.4 m², gennaker 40 m²)
Tension gauge
Spinlock Rig Sense
How it’s measured
Mast vertical: jib halyard taken gunwale to gunwale. Rake: tape hoisted on the main halyard, measured from the masthead to the top back edge of the transom above the rudder gudgeon. Wind caps and lowers down together to the table values.
Source
RS Sailing (rigging manual), Rigging Manual V16

Base setup

Rake
9550 mm
Base wind
7–11 kn
Cap shrouds (base)
275 on Rig Sense
Lowers (base)
155 on Rig Sense
Headstay
120 on the gauge with the backstay slack
Straightness
Sight up the track; adjust the lowers to move the bottom section
Security
Fit the velcro shroud straps between the bottlescrews at base and tape all split pins

Rough rig setting (full turns from base; tensions on Spinlock Rig Sense)

Wind (kn)Cap shroud (turns)Cap tensionLowers (turns)Lowers tensionJib carTack heightVang/kicker
0–6−2200−112012.5"Snug to max ease
7–11 (base)27515512"Snug to max ease
12–15+4400015521"Snug +
16–20+6475+1212.531"Tight
  • Called a 'rough rig setting' in the manual: a starting point for rigging rather than a full racing guide.
  • The 12–15 kn lowers are '0' turns but the same 155 tension as base, as printed.
  • The 95-page manual is too large for a plain fetch; it was re-checked page by page in a document viewer (rake, specification table and the 4.8 table).

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the RS21

Technical

RS21 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the RS21 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current RS21 class rules before changing equipment, and ask your class measurer if a part is not original equipment.