One-design race shop · Keelboat
X One Design (XOD) Race Shop
Everything you need to prepare, compete, and win.
Fit verified for X One Design (XOD)
All X One Design (XOD) equipment
33 parts
Fit verified for X One Design (XOD)
Lalizas
Lalizas Paddle, ?lack, L 86-39/64''(220Cm)
Part # LAL-50300
$26.92
Fit verified for X One Design (XOD)
Lalizas
Lalizas Paddle, Black, L 81'' (205 Cm)
Part # LAL-50290
$24.36
Fit verified for X One Design (XOD)
Johnson Pump
Johnson Pump Aqua Void 500 GPH Bilge Pump - 12V
Part # JPU-10-13626-01
$41.45
$50.97Fit verified for X One Design (XOD)
Albin Group
Albin Group Automatic Bilge Pump 1100 GPH - 12V
Part # alb-01-04-018
$72.98
$81.80Fit verified for X One Design (XOD)
Forespar
Forespar Aluminum Complete Whisker Pole (ADJ 7-15 DL) 83-169 In. (for 25 ft. Boat Max.) - 2 In. Dia.
Part # FOR407101
$547.16
$683.95Fit verified for X One Design (XOD)
Nuova Rade
Nuova Rade Heavy Duty Paddle With Palm Grip, Black, L 62'' (155 Cm)
Part # NVR-50240
$21.04
Fit verified for X One Design (XOD)
Attwood
Attwood Sahara MK2 S500 Bilge Pump 500 GPH - 12V - Automatic
Part # ATT-5505-7
$78.93
Fit verified for X One Design (XOD)
Lalizas
Lalizas Paddle, Black, L 73'' (185 Cm)
Part # LAL-50270
$20.25
Fit verified for X One Design (XOD)
Nuova Rade
Nuova Rade Standard Paddle, Black, L 60'' (150 Cm)
Part # NVR-50230
$10.81
Fit verified for X One Design (XOD)
Lalizas
Lalizas Paddle, Black, L 63'' (160 Cm)
Part # LAL-50250
$19.80
Fit verified for X One Design (XOD)
Forespar
Forespar Aluminum Complete Whisker Pole (ADJ 6-12 Ft.) 72-134 In. (for 25 ft. Boat Max.) - 1 1/4 In. Dia.
Part # FOR406000
$183.16
$228.95Fit verified for X One Design (XOD)
Lalizas
Lalizas Bailer For Water Removing, 0,66Gal (2,5Lt), 6-14/64 X 5-3/64 X 38/64'' (158X128X15Mm), Orange
Part # LAL-11919
$9.86
Fit verified for X One Design (XOD)
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 100' long
Part # buc-cro-nal38100
$41.18
Fit verified for X One Design (XOD)
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 150' long
Part # buc-cro-nal12150
$122.00
$123.70Fit verified for X One Design (XOD)
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 200' long
Part # buc-cro-nal12200
$161.00
$169.04Fit verified for X One Design (XOD)
Lewmar
Lewmar Rode - 150' 1/2"8Plt Splcd 5/16" Skl
Part # LEWHM150PX
$329.00
$498.95Fit verified for X One Design (XOD)
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 150' long
Part # buc-cro-nal38150
$70.70
Fit verified for X One Design (XOD)
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for X One Design (XOD)
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for X One Design (XOD)
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for X One Design (XOD)
Forespar
Forespar Aluminum Complete Whisker Pole (ADJ 6-12 DL) 79-138 In. (for 25 ft. Boat Max.) - 1 7/8 In. Dia.
Part # FOR406300
$487.16
$608.95Fit verified for X One Design (XOD)
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 1/4" x 100' - Yellow
Part # SDG-304206100YW-1
$15.73
$16.30Fit verified for X One Design (XOD)
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for X One Design (XOD)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for X One Design (XOD)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for X One Design (XOD)
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for X One Design (XOD)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for X One Design (XOD)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for X One Design (XOD)
Velocitek
Velocitek Prism (Digital Dinghy Compass)
Part # VELPRISM
$579.00
Fit verified for X One Design (XOD)
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for X One Design (XOD)
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for X One Design (XOD)
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No X One Design (XOD) parts match these filters.
Can’t find a part for your X One Design (XOD)? Request a X One Design (XOD) part
Go fast
X One Design (XOD) tuning guide
XODs vary a lot in hull shape and wooden-mast stiffness, so set-up is done by eye rather than by gauge: mast heel position, inners set off the running position, uppers sighted on a beat, and rake found by helm balance and recorded as a halyard mark. The only published set-up guide is the class association's tuning and tactics notes (based on Hyde sails); sailmakers otherwise publish sail-selection notes rather than numbers.
XOD Class Association — XOD Tuning & Tactics Undated (PDF in the class site's June 2016 uploads); credited to Colin McKinnon on the class tuning page. The PDF itself names no author and is written from boat X171's practice, with a 'secrets from X177' section
- Written for
- Starting points based on Hyde sails
- Tension gauge
- Not used – shrouds set by sighting the mast and counting turns
- How it’s measured
- Imperial units. Mast heel measured from the inside of the stem post to the front of the mast at heel level. Rake is recorded as a main-halyard mark on the side of the mast, with the boom about 1′ off the aft deck as the starting rake.
- Source
- XOD Class Association, Undated (PDF in the class site's June 2016 uploads); credited to Colin McKinnon on the class tuning page. The PDF itself names no author and is written from boat X171's practice, with a 'secrets from X177' section
Base setup
- Mast heel
- 6′ 4″ from the inside stem post to the front of the mast at heel level (the spinnaker pole, which should be 6′ 6″, makes a handy measure); lets the mast rake forward running without being inverted by the deck beam at the front of the mast gate
- Mast upright
- Check the mast is exactly upright fore-and-aft before tuning the inners and uppers
- Inners
- Set so the mast is held just off the deck beam at the front of the mast gate in the running position; then tie a stopper knot in the backstay so the mast stays straight and doesn't invert running. Inners symmetrical, mast not leaning to either side.
- Uppers
- Start finger tight; on a moderate day, beat with the rake set so the boom is about 1′ off the aft deck; let the uppers off a few turns at a time until the mast is straight (upper hounds over the inner hounds), checking on both tacks
- Upwind rake
- Set for balance: sails trimmed, crew hiked, the boat should hold course with the helm released. If it rounds up, reduce rake by 0.5″ of halyard against your mast mark and repeat; if rake gets too upright, move the heel forward and start again.
- Rake by wind
- Halyard slightly shorter (1″) in light air and slightly longer (2″) in heavy air
- Forestay
- Adjust so it carries no load upwind at maximum rake, but not so slack that the mast is at risk if the jib halyard fails
- Jib barberhauler
- Floating-block system; block height for a parallel slot, typically about 2 inches above the coaming (depends on the condition of the sails)
Trim by condition
- Jumpers
- Hard on in medium conditions; eased in light and heavy.
- Outhaul / inhaul
- X171 sets the foot to the black band and doesn't change the outhaul in a race; the inhaul flattens the lower main in heavy air – mark light, medium and heavy positions. Ease the inhaul downwind.
- Cunningham
- Only in very strong winds, to pull the draft forward.
- Mainsheet
- Re-reeve to 2:1 or even 1:1 in light air.
- Jib halyard
- Mark the tensioning line for light, medium and heavy.
- Jib sheeting angle
- Widen as the wind increases or in rough water; X171 rarely widens it inside the harbour.
- Reaching
- Spinnaker halyard about 4 inches below full hoist on a tight reach so the head clears the jumpers; pole for level clews. Medium air: backstay off and kicker for maximum power; heavy air: some backstay to flatten the main and ease the kicker to vent it.
- Running
- Backstay right off and rig forward to the stopper knot (don't invert the mast); main out, pole for maximum projected area with level clews; kicker controls twist and rolling.
- Downwind rake
- Let the mast forward on the backstay as far as possible, limited by the stopper knot.
- The author stresses that your sailmaker is the best adviser and that masts vary widely in stiffness: cut the main to suit your mast's bend.
- The X177 section refers to a Christian Brewer set-up and tuning guide on the Yachts and Yachting website; it couldn't be found online.
- Parts of the text date from around 1998–2002 (the X177 notes).
Sanders Sails — Understanding the Sanders XOD Sail Wardrobe February 2025
- Written for
- Jibs XJS1/XJS2, XJC3/XJC4/XJC5; mains XMC1, XMC4, XMC9; spinnakers XSL1, XSM2, XSR3
- Tension gauge
- Not applicable
- How it’s measured
- Sail-selection notes; no rig numbers.
- Source
- Sanders Sails, February 2025
Which sail for which rig and sea state
| Sail | Use |
|---|---|
| XJS1 (soft luff) / XJS2 (wire luff) jib | All-purpose, built for pointing in flatter water (western Solent); flatter entry, sheeted close to the coaming. XJS1 offered with 'S-M 25' and 'M-L 25' luff-clip offsets for more entry when forestay sag is needed in light air. |
| XJC3 (soft) / XJC4 (wire) jib | Deeper, more broad-seamed for chop (central Solent); needs careful forestay tension control |
| XJC5 jib | Development of XJC3 with a seam extended into the tack to hold foot shape and improve leech exit; sits between XJS1 and XJC3 |
| XMC1 main | Deep entry, crosscut; for masts whose top third bends |
| XMC4 main | More upper-leech twist, flatter exit; for masts that don't bend at the top; pairs with XJS2 |
| XMC9 main | Flatter entry for stiffer masts and tighter forestays |
| XSL1 spinnaker | Light air, up to 9 kn TWS |
| XSM2 spinnaker | All-purpose (Superkote 75) |
| XSR3 spinnaker | Deep running; needs care on reaches |
- Not a tuning guide: it helps match sails to mast stiffness, forestay tension and sea state but gives no rig settings.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
X One Design (XOD) resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the X One Design (XOD) by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current X One Design (XOD) class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesXOD Class Constitution and Rules 2026
- Class associationxonedesign.org.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a X One Design (XOD) part