One-design race shop · Keelboat
Farr 30 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Farr 30
All Farr 30 equipment
39 parts
Fit verified for Farr 30
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Farr 30
Harken
Harken Swivel Cam Cleat - Base (Standard) w/ Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR144
$180.95
$205.65Fit verified for Farr 30
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Farr 30
Lewmar
Lewmar Self Tailing Winch Ocean Size 30 - Aluminum Grey / Two Speed
Part # LEW49030000
$1,251.00
$2,018.95Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 10 in. / Plastic - Red / Single Hand Grip / Locking / Floating
Part # LEW29145311
$79.33
$113.95Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 10 in. / Chrome / Double Handle Grip / Locking
Part # LEW29141122
$196.00
$297.95Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 10 in. / Aluminum / Single Hand Grip / Locking
Part # LEW29141111
$125.00
$184.95Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Chrome / Single Hand Grip / Locking
Part # HARB8CL
$126.95
$181.20Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Aluminum / Speed Grip / Locking
Part # HARB8ASG
$109.95
$156.85Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Bronze / Single Hand Grip / Locking
Part # HARB8BL
$126.95
$180.90Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Aluminum / Single Hand Grip / Locking
Part # HARB10AL
$109.95
$156.85Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Chrome / Speed Grip / Locking
Part # HARB8CSG
$145.95
$208.00Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 10 in. / Chrome / Single Hand Grip / Locking
Part # LEW29141121
$153.00
$231.95Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Chrome / Single Hand Grip / Locking
Part # HARB10CL
$148.95
$212.85Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Chrome / Speed Grip / Locking
Part # HARB10CSG
$153.95
$220.15Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Aluminum / Single Hand Grip / Locking
Part # HARB8AL
$94.95
$135.00Fit verified for Farr 30
Harken
Harken Winch Handle - 8 in. / Aluminum / Ball Grip / Locking
Part # HARB8ASGLP
$106.95
$152.05Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Aluminum / Double Handle Grip / Locking
Part # HARB10ADL
$182.95
$261.50Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Bronze / Single Hand Grip / Locking
Part # HARB10BL
$193.95
$277.30Fit verified for Farr 30
Harken
Harken Winch Handle - 10 in. / Aluminum / Speed Grip / Locking
Part # HARB10ASG
$124.95
$177.55Fit verified for Farr 30
Harken
Harken Headsail Foil - Carbo Racing Foil Extrusion Only - Unit 0 - Extrusion Length: 39.4 ft (12.0 m)
Part # HAR700012MFOIL
$560.00
$806.85Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 8 in. / Aluminum / Single Hand Grip / Locking
Part # LEW29141011
$116.00
$170.95Fit verified for Farr 30
Lewmar
Lewmar 60mm Control Block - Single Ratchet
Part # LEW29901661BK
$93.35
$137.95Fit verified for Farr 30
Lewmar
Lewmar Winch Handle - 8 in. / Plastic - Red / Single Hand Grip / Locking / Floating
Part # LEW29145301
$74.19
$104.95Fit verified for Farr 30
Harken
Harken Cam Cleat - Carbo-Cam 365 (Standard) - Line: 1/8 to 3/8 in (3 to 10 mm)
Part # HAR365
$34.95
$40.10Fit verified for Farr 30
Harken
Harken Headsail Foil - Carbo Racing Foil Set - Unit 0 - Extrusion Length: 39.4 ft (12.0 m)
Part # HAR700012M
$900.95
$1,125.90
No Farr 30 parts match these filters.
Can’t find a part for your Farr 30? Request a Farr 30 part
Official Harken dealer
Farr 30 deck layout
- LOA
- 9.43 m (30.94 ft)
- Displacement
- 2,063 kg ( 4,548 lb)
- Ballast
- 950 kg (2095 lb)
- IM
- 11.67 m (38.29 ft)
- ISP
- 13.77 m (45.18 ft)
- SPL
- 4.14 m (13.58 ft)
- J
- 3.32 m (10.89 ft)
- P
- 12.36 m (40.55 ft)
- E
- 4.44 m (14.57 ft)
Mainsheet Traveler
-
2
57mm Block — SwivelHarken 2600
$55.95 -
3
29mm Double Block — SwivelHarken 342
$53.95 -
4
57mm Double Block — SwivelHarken 2602
$118.95 -
5
57mm Block — SwivelHarken 2600
$55.95 -
6
40mm Double Block — SwivelHarken 2638
$86.95 -
7
29mm Block — SwivelHarken 340
$29.95 -
8
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
9
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
10
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
11
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
12
57mm Double Block — SwivelHarken 2602
$118.95 -
15
29mm Block — SwivelHarken 340
$29.95 -
17
Standard Cam Base — SwivelHarken 144
$180.95 -
18
57mm Ratchet Block — SwivelHarken 2135
$86.95 -
19
40mm Block — SwivelHarken 2636
$38.95 -
23
40mm Block — SwivelHarken 2636
$38.95 -
24
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
25
Standard Cam-Matic® Cleat - 150Harken 150
$44.95
Mainsheet (side view)
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Farr 30 tuning guide
The Farr 30 (ex-Mumm 30) is tuned from a base around 9–15 kn by counting headstay, cap (V1) and diagonal (D1/D2) turns up or down with the wind, with rake set by a halyard-arc measurement to the headstay. North and Sail Technologies use different base tensions and gauges (North: caps 36 on RT-10, D1 hand tight, D2 6 on PT-1; Sail Technologies: caps 35 on RT-10, D1 10 and D2 7 on PT-2), so don't mix their numbers.
North Sails — Farr 30 Tuning Guide and Quick Tune Guide Tuning Guide 5.3.17; Quick Tune Guide 4.25.17
- Written for
- North 3DL/3Di main and headsails: Li-3, Mi-4, Hi-2 jibs; asymmetric and symmetric spinnakers
- Tension gauge
- Loos RT-10 for the caps (V1); Loos PT-1 for the D2s; Loos PT-2 for the D1s
- How it’s measured
- Rake by halyard arc: take a jib halyard to the top of the black band (BAS) at the gooseneck, swing it to the headstay, mark the headfoil and measure from the mark to the centre of the headstay pin. All measurements to the centre of clevis pins and bolts. Centre the rig with a tape on the centreline halyard from the hounds to the chainplate pins.
- Source
- North Sails, Tuning Guide 5.3.17; Quick Tune Guide 4.25.17
Base setup
- J
- 3,305 mm (10′ 10-1/8″), headstay pin to the fore face of the mast (without pole track)
- Mast position
- 3,440 mm (11′ 3-7/16″), forward bolt of the stemhead fitting to the front of the mast above the mast plate
- Mast foot
- 1,070 mm (3′ 6-1/8″) from mast foot to the fore bulkhead; may vary 15 mm
- Forestay
- 12.20 m (40′ 1/4″) pin to pin, or the halyard-arc measurement of 1.82 m (5′ 11-5/8″) at base
- Caps (V1)
- 36 on the RT-10 at base
- D2s
- 6 on the PT-1
- D1s
- Hand tight (PT-2); re-check the caps are still 36 and ease to stay there – this is the base tune
- Mast partners
- Mast at maximum J; partners secure so the mast isn't point-loaded
- Backstay
- Light air (5 kn): bottom floating block 50 mm (2″) below the top lifeline. Maximum: block 230 mm (8″) or two-blocked below the bottom lifeline (stern lifelines tight when measuring). Backstay strop length shown as 2,070 (6′ 9-1/2″).
- Spreader marks
- On the lower spreader, measured from the inside edge of the cap shroud: 22 cm (8″), 8 cm (10″), 30.4 cm (12″), 35.5 cm (14″), 40.5 cm (16″), 45.7 cm (18″)
- Jib inhauler marks
- Fairlead outside edge 467 mm (18-3/8″) aft of the aft face of the mast partners; measure in 9 cm (3-5/8″) from the inboard edge of the sheet and mark every 3 cm (1-1/8″) for 7 marks
Rig tuning chart (full turns from BASE)
| TWS (kn) | Sail | Headstay | V1 (caps) | D1 | D2 |
|---|---|---|---|---|---|
| 0–6 | Li-3 | −6 turns | −2 turns | −3 turns | Base |
| 7–8 | Li-3 | −4 turns | −1 turn | −1 turn | Base |
| 9–10 (BASE) | Li-3 / Mi-4 | BASE (arc 1820 mm) | BASE (36 RT-10) | BASE (hand tight) | BASE (6 PT-1) |
| 11–12 | Mi-4 | +4 turns | +1 turn (41 RT-10) | +1 turn (6 PT-2) | Base (6 PT-1) |
| 13–14 | Mi-4 | +8 turns | +2 turns | +1 turn | Base |
| 15–18 | Mi-4 / Hi-2 | +14 turns | +3 turns | +2 turns | Base |
| 19+ | Hi-2 | +20 turns | +3 turns | +2 turns | Base |
Mainsail trim
| Control | Light | Medium | Heavy |
|---|---|---|---|
| Boom / traveller | Above centre | Just below centre | Ease to coaming |
| Vang | None | Some | Max |
| Outhaul | 100 mm sag | Firm | Max |
| Cunningham | None | 100 mm | Max |
Jib inhauler set-up (spreader marks: inboard #4, outboard #1)
| True wind (kn) | Inhauler mark | Spreader mark, flat water | Spreader mark, rough water |
|---|---|---|---|
| 0–5 | #1 | #3–4 | #3 |
| 5–10 | #2–3 | #3–2 | #3 |
| 10–15 | #3–4 | #2 | #2 |
| 15–20 | #5–OFF | #2–1 | #1 |
| 20–25 | OFF | Outside spreader tip | Outside spreader tip |
| 25–30 | OFF | Outside spreader tip | Outside spreader tip |
Trim by condition
- Main, light
- Strong trimmers can sheet on the coarse purchase only. Flat water: top telltale flicking in and out; boom can sit above centreline with the traveller car 228 mm (9″) from the side of the cockpit. Chop: top telltale flowing all the time, traveller down 150 mm (6″), outhaul eased to 100 mm (4″) of foot sag, cunningham off.
- Main, medium
- Play the traveller constantly and ease the fine-tune 150 mm (6″) in gusts; boom just below centreline most of the time; moderate vang (ease it at the top mark); outhaul firm with no sag; cunningham on 100 mm (4″).
- Main, heavy
- Boom eased to the coaming but trimmed in the lulls to point; slight vang load at full sheet; outhaul tight with a crease along the boom; cunningham maximum. Overpowered upwind, try easing the fine-tune 150 mm (6″).
- Jib, light
- Inhauler needed; if stalled, ease inhauler/sheet so the leech sits at the spreader tip; ease the forestay 25 mm (1″).
- Jib, medium
- Some inhauler; if stalled or backwinding the main, ease until the leech is at the second outside spreader mark; take up the forestay 25 mm (1″); halyard firm with a few wrinkles.
- Jib, heavy
- No inhauler; leech to the spreader tip if stalled; take up the forestay 50 mm (2″); halyard tight with no wrinkles.
- Asymmetric
- Pole set 460 mm (18″) above the deck beside the headstay; mark the guy at the winch. Ease the leeward inhaulers when reaching.
- Symmetric
- At about 16 kn the luff should fly straight, perpendicular to the pole.
- Crew
- Optimum heel 15–20°. First crew on the rail sits against the windward stanchion 60 cm (24″) aft of the shroud.
- The spreader-mark list reads '8 cm (10″)' between 22 cm (8″) and 30.4 cm (12″); this looks like a typo for about 25 cm.
- Maximum backstay is given as '230 mm (8″)' (230 mm is closer to 9″), and the strop length as '2,070m (6′9-1/2″)' – both as printed.
- The full guide also includes an original Farr VPP polar table (not reproduced here). The Quick Tune Guide (https://cdn.shopify.com/s/files/1/0688/6549/1220/files/3-NS-QuickTuningGuide_Farr30_4.25.17.pdf?v=1747845464) repeats the same tuning chart and base measurements.
Sail Technologies — Farr 30 Tuning Guidelines Current web page (undated)
- Written for
- Light, medium and heavy jibs; masthead light, heavy and A spinnakers
- Tension gauge
- Loos RT-10 rod gauge for the caps; Loos PT-2 wire gauge for the D1s and D2s
- How it’s measured
- Rake by swing arc: centreline halyard pulled down to the top of the black band, swung forward to mark the headstay.
- Source
- Sail Technologies, Current web page (undated)
Base setup
- Headstay
- 12140 mm pin to pin
- Cap shrouds
- #35 on the RT-10
- D1
- #10 on the PT-2
- D2
- #7 on the PT-2
- J
- 3315 mm
- Mast base
- 3480 mm from the forward headstay bolt to the front of the mast
- Prebend
- 75 mm
Quick adjustments (turns from base)
| TWS (kn) | Sails | Headstay | Caps | D1s | D2s |
|---|---|---|---|---|---|
| 0–5 | Light jib / masthead light spin / masthead A spin | −10 | −2 | −2 | Base |
| 5–9 | Light jib / masthead light spin | −7 | −1 | −1 | Base |
| 10–15 | Medium jib / masthead light spin | Base | Base | Base | Base |
| 16–20 | Medium jib / masthead heavy spin | +7 | +1 | +2 | Base |
| 21+ | Heavy jib / masthead heavy spin | +15 | +2 | +3 | +2 |
- Base dimensions differ slightly from North's (headstay 12140 vs 12200 mm, J 3315 vs 3305 mm, mast 3480 vs 3440 mm from the stem bolt), and the D2 is read on a PT-2 rather than a PT-1.
- No sail-trim notes are given.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Farr 30 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Farr 30 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Farr 30. Racing legality depends on your class or handicap rules; check them before changing equipment.