One-design race shop · Dinghy

Sunfish Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Sunfish

  • 17 verified parts
  • 7 brands
  • Fit checked Nov 2026

Fit verified for Sunfish

All Sunfish equipment

17 parts

Can’t find a part for your Sunfish? Request a Sunfish part

Go fast

Sunfish tuning guide

Sunfish tuning means halyard position on the gaff, gooseneck position along the boom (inches from the spar apex), vang tension, and outhaul and cunningham trim. The class's own tuning guide is Scott Kyle's 1992 article, written for the North racing sail and the boat of that era, so treat its numbers as a starting point.

Scott Kyle (Sailing World article, hosted by the Sunfish class) — Sunfish Tuning Guide for Racers Sailing World, June 1992 (transcribed reprint, PDF 2001)

Written for
Sunfish North racing sail (introduced 1988)
Tension gauge
Not applicable
How it’s measured
Halyard positions are tape marks on the gaff (by clip number or inches down); gooseneck height above deck before vang tension; gooseneck position as inches along the boom from the apex of the spars (boom marked at 1″ intervals from 17″ to 23″).
Source
Scott Kyle (Sailing World article, hosted by the Sunfish class), Sailing World, June 1992 (transcribed reprint, PDF 2001)

Base setup

Halyard
Pre-stretch or low-stretch line, about 24 ft of ¼″, with a purchase to keep the gaff snug to the mast; four taped marks on the gaff (light, medium, heavy, Jens). Tie with a clove hitch just below the mark.
Gooseneck height after vanging
Ends up two to three inches above the deck whatever the wind; a lower halyard position lets you vang harder and still keep it about 3″ up
Bridle
Replace the wire bridle with 30″ of pre-stretch line (the then-minimum length); check current rules
Tiller extension
About 37–38″, just skimming the ratchet base
Telltales
One pair at the top of the third (middle) panel about 30″ from the gaff, one pair at the bottom of the second panel about 26″ from the gaff; gaff streamers two to three feet from the spar apex
Skipper weight
Optimal all-round weight about 165 lb

Halyard position, gooseneck height and vang

WindHalyard positionGooseneck height (before vang)Vang tension
Light air10th clip3″Light
Medium air1–2″ down4–5″Medium
Heavy air2–3″ down5–8″Hard
Jens rig10–12″ down5–8″Hard

Gooseneck position (inches from the apex of the spars)

WindGooseneck setting
Under 5 kn17–18
5–8 kn18–19
8–12 kn19–20
12–15 kn20–21
15–20 kn21–22
20–25 kn22–23
Over 25 knJens rig, 20–21

Trim by condition

Gooseneck
Lighter wind and flatter water: further forward (17″ helps pointing); move it back as wind and waves build. Lots of weather helm: move it back regardless of wind; poor pointing: move it forward. Set for the conditions expected for most of the race (e.g. a 5 kn breeze forecast to build to 18 kn: about 19–20″).
Jens rig
Move the gooseneck a couple of inches forward of your heavy-air, non-Jens position, since the Jens rig already neutralises the helm.
Vang
Rigged with the halyard tail over the gooseneck and round the mast; even in light air use a little to hold leech tension downwind.
Outhaul and cunningham
Light air, flat water: outhaul fairly tight with minimal scallops along the foot; cunningham just loose enough for a smooth shape on port tack. Bigger waves: ease both so scallops show along foot and luff. Overpowered: tighten both; in very heavy air the outhaul stretches to within an inch of the boom end and the luff is tight with no scallops. Ease both at the windward mark for downwind.
Port vs starboard
The sail is flatter on port tack. Light air: don't oversheet on port; the fuller starboard-tack sail tolerates tighter sheeting. Heavy air: sheet tighter on port; ease sooner in puffs on starboard.
Heel and weight
Light air, flat water: sit far forward, about 5° heel; in light-medium chop about 10°, flattening once through the waves. In breeze sail very flat and slide aft, especially in waves; ease before the puff hits.
Downwind
Light air: considerable windward heel and the board as high as you can steer with: about 6″ of board under water on a run under 10 kn, 6–12″ on a reach. Heavier air: slightly less windward heel; drop the board a few inches if the boat gets squirrelly.
  • Written in 1992 for the North racing sail and the boat as it was then; the transcription itself flags an omission about the "new" daggerboard and says to check current rules on the bridle.
  • The same transcription is also hosted at myc.org/wp-content/uploads/2020/11/Sunfish-Tuning-Guide-by-Scott-Kyle.pdf.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-03). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Sunfish resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Sunfish by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Sunfish class rules before changing equipment, and ask your class measurer if a part is not original equipment.