One-design race shop · Dinghy
Club 420 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Club 420
All Club 420 equipment
20 parts
Fit verified for Club 420
Harken
Harken Block - Carbo 40mm Single - 90° Fixed Head
Part # HAR2659
$42.95
$48.65Fit verified for Club 420
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Club 420
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Club 420
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Club 420
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Club 420
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for Club 420
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Club 420
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Club 420
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Club 420
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Club 420
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Club 420
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for Club 420
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Club 420 parts match these filters.
Can’t find a part for your Club 420? Request a Club 420 part
Official Harken dealer
Club 420 deck layout
- Length
- 13.90 ft (4.24 m)
- Beam
- 5.50 ft (1.68 m)
- Mainsail Area
- 79.65 sq. ft (7.40 sq. m)
- Jib
- 30.14 sq. ft (2.80 sq. m)
- Spinnaker
- 95 sq. ft (8.83 sq. m)
- Hull Weight
- 230 lb (104.33 kg)
Mainsheet System
-
1
40mm 90° BlockHarken 2659
$42.95 -
2
40mm 90° BlockHarken 2659
$42.95 -
3
40mm 90° BlockHarken 2659
$42.95 -
4
57mm Ratchet Block — SwivelHarken 2135
$86.95
Vang
-
1
16mm BlockHarken 404
$17.95 -
5
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
6
40mm T2™ Soft-Attach BlockHarken 2149
$44.95 -
7
40mm 90° BlockHarken 2659
$42.95 -
8
40mm 90° BlockHarken 2659
$42.95 -
9
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
10
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
11
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
12
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
13
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
16
57mm Ratchet Block — SwivelHarken 2135
$86.95
Jib Halyard
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Club 420 tuning guide
The Club 420 is tuned with mast-butt position, shroud pin holes and jib-halyard rig tension, which together set rake; the boat is stiff, so rig tension mainly controls jib luff sag. The guides disagree on where rake is measured (top of the transom versus where the transom meets the hull bottom), so their rake numbers can't be compared directly, and tension is given in pounds or as Loos readings with no model stated.
Zim Sailing — Zim 420 Rigging & Tuning Guide 2012 (document dated 29 Jan 2012)
- Written for
- Not stated (builder's rigging and tuning guide for Zim-built 420s)
- Tension gauge
- Approximate tension in pounds plus a 'Loos #' column; the Loos model isn't stated
- How it’s measured
- Rake from the masthead to the top of the stern. Mark the jib halyard against the mast at each setting so rig tension can be repeated, and write the wind/pin settings on the deck by the shroud.
- Source
- Zim Sailing, 2012 (document dated 29 Jan 2012)
Base setup
- Mast pin (butt)
- Second hole from the front
- Jib tack
- Aft-most pin on the forward chainplate; forestay on the middle pin
- General rule
- Avoid jib luff sag as the breeze fills; whenever rake changes, re-set bridle and vang for leech trim
Rig settings by breeze (tension in lb and Loos reading, model not stated)
| Breeze | Shroud adjuster pin | ~Rake (top of stern) | ~Tension | Loos # |
|---|---|---|---|---|
| Light | 4 Back | 20'9" | 180 lb | 18 |
| Medium | 6 Forward | 20'7-1/2" | 260 lb | 22 |
| Heavy | 7 Forward | 20'4-1/2" | 280 lb | 23 |
| Honking | 8 Forward | 20'2-1/2" | 345 lb | 26 |
- Wind ranges are named (light to honking), not given in knots.
- Hosted by the Club 420 Class Association; the rest of the document is assembly instructions.
North Sails — North Club 420 tuning guide and Upwind Sail Trim Chart Undated (scanned copy posted by the class in 2016)
- Written for
- North Club 420 main, jib and spinnaker
- Tension gauge
- Loos 'model PTI' (printed that way; presumably the PT-1) or the older Model A, on the 1/8" side stays. North says readings are only relative and vary even between new gauges.
- How it’s measured
- Rake: tape hoisted on the main halyard, led over the top of the transom and down its aft face to where the transom meets the hull bottom. Mast step: transom along the floor to the back of the mast.
- Source
- North Sails, Undated (scanned copy posted by the class in 2016)
Base setup
- Mast step
- 9'-4 1/2" from the transom along the floor to the back of the mast (usually the first pin hole from the front)
- Rake range (club/junior)
- 21'-6 1/2" in light air to 20'-9 1/2" in near-survival conditions; change tension along with rake
- Rig tension range
- 240 lb in light air to a maximum 360 lb in near-survival conditions
- Tension check
- Set correctly upwind when the leeward shroud just starts to go slack (not dangling)
- Changing rig on the water
- Ease the jib halyard until the forestay takes the load, move the leeward shroud pin, tack and repeat; re-tension with the 3:1 halyard purchase
- Mast blocks
- Not needed in light air; in breeze fill the partners in front of the mast to within about 1/8"–1/4"
North C420 Upwind Sail Trim Chart (wind in mph; tension in lb)
| Wind (mph) | Rake | Rig tension | Mast blocks | Centreboard | Cunningham | Outhaul | Mainsheet | Vang | Jib sheet windward | Jib sheet leeward |
|---|---|---|---|---|---|---|---|---|---|---|
| 0–6 | 21' 6 1/2" | 240 | None | Max down | Wrinkles in full luff | No vertical wrinkles | Upper batten open 10" | Loose | 1 1/2" | Eased |
| 7–12 | 21' 3 1/2" | 280 | None | Max down | Wrinkles in lower 3/4 luff | No vertical wrinkles | Upper batten parallel | Loose | 2" | Tighter (foot taut) |
| 12–18 | 20' 1/2" | 320 | +1/4" gap | Max down | Wrinkles in lower 1/2 luff | More tension | Upper batten parallel | Medium | 1 1/2" | Tighter (foot taut) |
| 19+ | 20' 9 1/2" | 360 | +1/8" gap | Up 2–3" | No wrinkles in luff | Maximum tension | Upper batten open 10" | Max (slight overbend wrinkles) | None | Tight (foot smooth) |
Trim by condition
- Rake by crew weight
- Rake aft as you become overpowered. Crews over 270 lb can stay more upright longer; crews under 240 lb should rake aft earlier. If the boom is consistently outside the boat's corner to keep the boat flat, rake further aft.
- College sailing
- Shrouds can't be changed, so raking aft with the halyard gives a looser rig; sail with less vang in breeze to avoid headstay sag and overbend.
- Centreboard
- Fully down upwind; up to 2–3" up when badly overpowered. Off the wind raise it until the helm is neutral.
- Top batten
- Tension just until the wrinkles at the pocket disappear.
- Main luff
- Wrinkles tack to head in light air; nearly smooth in breeze. Set the halyard with slight wrinkles and fine-tune with the cunningham in puffy conditions.
- Outhaul
- Light air: just remove vertical wrinkles. Tighten progressively; in near-survival the foot tape stands straight up off the boom. Downwind ease until the foot is just smooth.
- Mainsheet
- Last 18" of the top batten nearly parallel to the boom; harder to point briefly, eased for power and acceleration. Play it constantly.
- Vang
- Downwind: last 18" of the top batten nearly parallel to the boom. Upwind light air: loose enough for the upper batten to open 15–20° when the sheet is eased. Increase with breeze to slight overbend wrinkles just below the spreader; in near-survival it can pay to ease it.
- Jib sheets
- Leeward sheet in until slight creases tack to clew; windward sheet until the creases just disappear (about 1 1/2"–2"). Ease the leeward, not the windward, to accelerate. No windward sheet in breeze.
- Spinnaker
- 4"–8" of curl in the luff at all times; pole roughly horizontal (lower in light air, higher in breeze to keep the clews level) and nearly perpendicular to the wind; ease the halyard about 6" off the masthead.
- Crew position
- Light air: helm just forward of the traveller, crew just forward of the centreboard thwart; move aft as the breeze builds.
- The 12–18 mph rake cell reads 20' 1/2", which is shorter than the 19+ value of 20' 9 1/2" and outside the 21'6 1/2"–20'9 1/2" range in the text; it may be a typo for 21' 1/2". Shown as printed.
- Wind is in mph, not knots. Rake is measured to the bottom of the transom, so it is much longer than the Vanguard and Zim numbers measured to the top of the transom.
- The class's PDF is a copy generated on an iPhone in June 2016 (it reads like a saved web page, with some typos in the text); the guide's own date isn't stated.
Vanguard Sailboats — Vanguard Sailboats Guide to Tuning the New C420 Sails 2005 (for the sails redesigned in spring 2003)
- Written for
- 2003-design Club 420 class sails (mast-slug main tack, higher jib clew)
- Tension gauge
- Shroud tension in pounds; gauge not named
- How it’s measured
- Rake: tape on the main halyard to the masthead, measured to the top of the transom on the centreline with the rig fully tensioned (jib hoisted to full tension). If too long, lower the shroud pins and re-measure.
- Source
- Vanguard Sailboats, 2005 (for the sails redesigned in spring 2003)
Base setup
- Mast butt
- Settings are for the butt 2 holes back from the forward-most hole (the new sails allow 1–2 holes aft of 'pin max forward')
- Crew weight basis
- About 250 lb combined; much lighter crews move up one wind range, much heavier crews down one; move down one range in significant chop
- Maximum shroud tension
- 350 lb recommended; breakdowns are likely above 400 lb
Settings guide by wind (tension in lb; rake to top of transom)
| Wind (kn) | Rake | Shroud tension | Centreboard | Bridle (block sheave top from board cap) | Mainsheet | Vang | Outhaul | Cunningham | Jib trim |
|---|---|---|---|---|---|---|---|---|---|
| 0–4 | 20'3" | 100 | Full down | 21" | Top batten telltale flying constantly | Loose | Slight horizontal wrinkles along boom | Loose, only a few horizontal wrinkles | Firm leeward, slight or no windward sheet |
| 5–8 | 20'4" | 140 (leeward shroud a tiny bit loose upwind) | Full down | 21" | Top batten telltale stalling often | Very slight tension | Slight horizontal wrinkles along boom | Loose to none | Firm leeward, firm windward |
| 9–11 | 20'3" | 200 | Full down | 20" | Firm | Neutral in lulls, slight in puffs | Horizontal wrinkles along boom | Very slight tension | Very firm leeward and windward |
| 12–14 | 20'2" | 230 | Full down | 17" | As hard as you can pull | Firm | Hard horizontal wrinkles along boom | Tensioned | Very firm leeward and windward |
| 15–18 | 19'11" | 300 | Raised 1" | 16" | Pull hard until heeling too much | Very firm | Hard horizontal wrinkles along boom | Hard | Extremely firm leeward, moderate windward |
| 19+ | 19'10" | 330 | Raised 3" | 15" | Pull hard until heeling too much, then ease, hike, trim | Very firm | Hard horizontal wrinkles along boom | Hard | Extremely firm leeward, slight to slack windward |
Trim by condition
- Rig tension
- More tension tightens the jib luff wire, flattening the jib and opening its leech so you can sheet harder and point; less tension gives fuller sails for light air.
- Rake
- More rake opens the slot and depowers (better speed, lower pointing); rake forward if underpowered and not pointing.
- Mast butt
- Weather helm combined with poor pointing suggests moving the butt aft.
- Main
- The newer main is flatter low down, so you can sheet hard for the top without over-closing the lower leech; in breeze use vang and sheet together for twist.
- Fault finder
- Poor pointing: check bridle height, main and jib sheet tension (both sheets), too much rake, butt too far forward, too much rig tension. Poor speed: check for over-trimmed sheets, too little rake, too little rig tension.
- Written by Brian Doyle (US Sailing) and Dave Kirkpatrick (Vanguard). The 0–4 kn rake (20'3") is shorter than the 5–8 kn rake (20'4"); shown as printed.
- The foot and inch marks are garbled in the PDF's text layer; values read as feet'inches".
College of Charleston (Greg Fisher) — 420 Tuning suggestions 2012
- Written for
- Club 420 (college fleet), loose-footed main
- Tension gauge
- None; rig tension is judged by leeward-shroud slack
- How it’s measured
- Tension the rig ashore with a foot on the bow while the crew pulls the jib halyard; check on the water by watching the leeward shroud.
- Source
- College of Charleston (Greg Fisher), 2012
Base setup
- Rig tension target
- Leeward shroud just starts to slacken, showing no more than about 1/2" of wiggle at full main trim; more wiggle in light lumpy water, almost none in breezy puffy conditions
Trim by condition
- Outhaul
- Start with a fist-width (2 1/2"–3") gap between the main foot and the boom above the mainsheet blocks; when fully hiked with heavy vang, about half a fist (about 1 1/2"). Don't ease past a fist in light air or adjust it downwind.
- Vang
- Totally loose upwind in light air; hard when overpowered, to the point where overbend wrinkles appear in the lower 1/4 of the main, angling from the mast toward the clew and fading about 1/2–2/3 of the way back along the boom; then add cunningham until they are just visible. Ease at the windward mark and play it downwind (top-batten telltale nearly always flying; last 18" of the top batten parallel to the boom).
- Cunningham
- Loose in light air (tack floats 2–3" above the boom); medium air wrinkles only up to the spreaders; very tight when overpowered. Older sails need a little more. Ease fully downwind and reset before the leeward mark.
- Mainsheet
- Upwind the top-batten telltale stalls about 75% of the time when trimmed right. Very light air: boom 12–24" to leeward. Never heel more than 10° to balance helm.
- Windward jib sheet
- Trim 3–4" past just-taut so the clew moves 2–3" to weather; not used in very light or near-survival winds.
- Leeward jib sheet
- Trim until the foot is smooth, set the windward sheet, then trim another 3–5" once at speed. In big puffs ease 3–6" and re-trim; the jib leech telltale should always just fly.
- A coaching handout by Greg Fisher for the College of Charleston team, hosted by the class association. Inch values are as printed; some fractions are garbled in the PDF text.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Club 420 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Club 420 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Club 420 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesClub 420 Class Rules, updated February 3, 2022
- Class associationclub420.org
- Builder specificationsClub 420 on zimsailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Club 420 part