One-design race shop · Dinghy
RS600 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS600
All RS600 equipment
35 parts
Fit verified for RS600
Rooster
Rooster Tiller Extension (Carbon Fibre) - Length: 6.9 ft (2100 mm) - 22 mm Dia.
Part # ROO128576
$217.80
$242.00Fit verified for RS600
Selden
Selden 20 Ball Bearing Block - Single Cheek
Part # sel-402-101-13r
$23.80
$28.00Fit verified for RS600
Harken
Harken Cam Cleats - Wedge Kit (Micro) - For Carbo-Cam 471
Part # HAR297
$5.95
$6.90Fit verified for RS600
Rooster
Rooster Tiller Extension (Carbon Fibre) - Length: 6.9 ft (2100 mm) - 25 mm Dia.
Part # ROO128577
$217.80
$242.00Fit verified for RS600
Harken
Harken Block - Carbo 40mm Single - 90° Fixed Head
Part # HAR2659
$42.95
$48.65Fit verified for RS600
Selden
Selden Pop-rivet, ø4,8 X 9,9 mm, Monel, Dome Head
Part # sel-167-007-10
$45.00
Fit verified for RS600
Harken
Harken Cam Cleat - Carbo-Cam (Micro) 471 - Line: 1/8 to 1/4 in (3 to 6 mm)
Part # HAR471
$31.95
$36.50Fit verified for RS600
Harken
Harken Swivel Cam Cleat - Base (Small) w/ Cam-Matic 150 - Line: 1/4 to 5/8 in (6 to 16 mm)
Part # HAR205
$163.95
$186.05Fit verified for RS600
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for RS600
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for RS600
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for RS600
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for RS600
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for RS600
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for RS600
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for RS600
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for RS600
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for RS600
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for RS600
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for RS600
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for RS600
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for RS600
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for RS600
Ronstan
Ronstan Trapeze Handles, Vertical grip - Red - Pair
Part # RONRF5122R-2
$42.16
$49.60
No RS600 parts match these filters.
Can’t find a part for your RS600? Request a RS600 part
Go fast
RS600 tuning guide
The RS600's carbon rig is set ashore with rake (about 6900 mm in 10–18 kn), rig tension (100 lb light to 200+ lb windy) and diamond tension sized to the helm's weight; on the water the kicker and cunningham do most of the depowering, and the reefed rig needs a new rake benchmark. Tensions are quoted in pounds without a named gauge, and both available guides date from the early 2000s.
RS Class Association — RS600 Tuning Guide Undated (PDF dated June 2004)
- Written for
- Class Hyde mainsail, full and reefed rig
- Tension gauge
- Not named (pounds)
- How it’s measured
- Rake from the top of the mast to the transom bar on the centreline; use chainplate holes only once you've set a benchmark.
- Source
- RS Class Association, Undated (PDF dated June 2004)
Base setup
- Wing set
- Under 70 kg wide wings (7 ft beam); 70–76 kg wide or narrow (wide needs 3 kg lead); over 76 kg narrow (6 ft 4 in)
- Helm weight
- Very light (under 10 st) or very heavy (over 15 st) helms may need a slightly different benchmark
- Rake, medium airs (10–18 kn)
- 6900 mm (on most boats 3rd hole down from the top of the chainplates)
- Rake, light airs
- Up the chainplate one hole
- Rake, over 18 kn
- Down up to three holes, usually one
- Reefed rig
- Reset the benchmark; shrouds much lower, maybe the bottom hole
- Rig tension
- Medium 150–200 lb; light about 100 lb; strong above 200 lb (flatter water needs less)
- Diamonds
- About 30 lb for a 10 st sailor up to 100 lb for 15 st
- Spreaders
- Fixed, all the same length
Trim by condition
- Prebend via halyard
- Hoist fully, then pull about another 2″ of halyard down with the cunningham through a slip knot and cleat (wears the halyard and headboard).
- Cunningham and kicker
- Use as much cunningham as you can upwind in a breeze; kicker slightly loaded ashore with the halyard set, block-to-block when beating in over 10 kn.
- Battens
- Tied in to remove creases, but not so tight the sail won't lie flat.
- The document text names no author (PDF metadata lists Anthony York). The 2002 class booklet refers readers to 'Andy Irons' RS600 Tuning Guide', and the numbers here match the Irons settings it quotes.
RS Class Association — RS600 Training and Rigging Guide (Rig Settings; Kicker, Cunningham & Outhaul) 2002 (Roland Emmans, RS600 class representative)
- Written for
- Class Hyde mainsail (12.14 m² full, 10.55 m² reefed)
- Tension gauge
- Not named (pounds)
- How it’s measured
- Rake from the top of the mast to the centre of the transom line.
- Source
- RS Class Association, 2002 (Roland Emmans, RS600 class representative)
Base setup
- Mast rake (Andy Irons)
- 6900 mm for 10–18 kn (three holes down on most boats); up one hole in lighter airs, down at least one in windier
- Rig tension
- Light about 100 lb (only on flat water); medium 150–200 lb; windy above 200 lb or as much as you can pull
- Diamonds
- 10 st sailors about 30 lb; 15 st up to 100 lb (tighter = more power, less forgiving)
- Reefing
- Fleet opinion: change down at about 18 kn (higher for flat water or heavier sailors)
Controls by wind
| Wind / leg | Kicker | Cunningham | Outhaul | Board |
|---|---|---|---|---|
| Light, beating (not trapezing) | Until the leech starts to hook (none if not on the wing) | None (creases are fast) | Max a quarter on, about 1″ off the boom mid-foot | — |
| Light, reaching | Enough to power up once on the side | Little | — | Up to a quarter up (more on a broad reach) |
| Light, running | Off | Off | Off | Half up or as far as comfortable |
| Medium, beating (trapezing) | At least half, more as wind rises | Only when the boat trips/stalls | ½ to 1/3 on | — |
| Medium, reaching | On (release cunningham by easing kicker first) | Less / none | — | Unchanged |
| Windy, beating | Full | Full | More on if still overpowered | — |
| Windy, reaching | Full as long as possible | Full | Half off | — |
| Windy, running | Just enough to balance | At least half off | Half off | — |
Trim by condition
- Depowering order
- Kicker, then downhaul, then more kicker, then more downhaul until both are tight; then outhaul.
- Training-and-rigging booklet; rig numbers are credited to Andy Irons' article.
LDC Racing Sailboats (RS builder) — RS600 Owner's Manual (rigging instructions; tuning and sailing tips) Undated (PDF created June 2003)
- Written for
- Standard RS600 rig, full and reefed
- Tension gauge
- Not named (shroud load given as an approximate figure in pounds)
- How it’s measured
- No rake measurement given; rake is set by chainplate hole.
- Source
- LDC Racing Sailboats (RS builder), Undated (PDF created June 2003)
Base setup
- Rake starting point
- Middle of the chainplates gives a good average rake
- Rig tension
- Firm two-handed pull on the 2:1 forestay purchase, giving roughly 250 lb on the shrouds
- Diamonds
- Set to helm weight before stepping the mast: lighter helm, less tension, but always enough to keep the wires seated on the spreader ends
- Reefing
- Top sailors reef from about 15–20 kn upwards; light sailors may be faster and safer reefed above 12 kn
Trim by condition
- Battens
- Tighter as the wind rises; just enough to remove wrinkles suits most club sailing.
- Cunningham
- Hard on in light air, eased a little to power up from marginal trapezing to full power, then harder again once overpowered; maximum tension flattens the upper leech when struggling.
- Kicker
- More as the wind rises; ease in very gusty conditions and substantially on runs.
- Daggerboard
- Normally fully down; in very windy conditions raise it about 200 mm and leave it.
- Tacking
- Ease at least 200 mm of mainsheet before tacking, 500 mm or more when very windy.
- Builder's owner manual rather than a dedicated tuning guide; added at audit.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
RS600 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS600 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS600 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRS Class Association Rules All Classes v4 June 2022; RS600 Rules (undated)
- Class associationrs600.org
- Builder specificationsRS600 on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS600 part