One-design race shop · Other
Hobie Mirage Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Hobie Mirage
All Hobie Mirage equipment
5 parts
Fit verified for Hobie Mirage
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Hobie Mirage
Tylaska
Tylaska Spares – Fastales Wool Tell Tales
Part # TYL-TYBK-FT1
$15.99
Fit verified for Hobie Mirage
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Hobie Mirage
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Hobie Mirage parts match these filters.
Can’t find a part for your Hobie Mirage? Request a Hobie Mirage part
Go fast
Hobie Mirage tuning guide
The Hobie Mirage Adventure Island (16′7″, 65 ft² sail) and Mirage Tandem Island (18′6″, 90 ft²) are rotomoulded trimaran pedal/sail kayaks with an unstayed two-piece mast, a roller-furling square-top mainsail with three vertical battens, a centreboard and MirageDrive pedal propulsion. There is no standing rigging to tune and no sailmaker or class guide; the only published setup and sail-handling guidance is Hobie's owner's manual, whose assembly and 'Sailing Basics' sections are transcribed below (no numeric settings beyond the spec sheet).
Hobie Cat Company (builder owner's manual) — Hobie Mirage Adventure Island Manual PN 89601, REV 150701 (listed by Hobie Support as the 2015–2016 Mirage Adventure Island manual)
- Written for
- Stock square-top roller-furling mainsail with 3-piece batten set; telltales fitted both sides
- Tension gauge
- None — unstayed mast; the only sail controls are the downhaul at the mast collar, batten-cap lacing, the furling line and the mainsheet
- How it’s measured
- No measurements. Assembly is mast → sail sleeve → head webbing into mast cap → downhaul tensioned and cleated → sail rolled onto the mast counter-clockwise → mast dropped through the forward crossbar bearing until it locks.
- Source
- Hobie Cat Company (builder owner's manual), PN 89601, REV 150701 (listed by Hobie Support as the 2015–2016 Mirage Adventure Island manual)
Base setup
- Mast / sail assembly
- Slide the two mast halves together, insert the mast into the sail sleeve, insert the webbing at the head into the mast cap
- Downhaul
- Feed through the loop on the mast collar, pull tension to tighten the sail onto the mast, cleat, and knot the tail for security
- Battens
- Slide the batten cap over the batten ends, lace and tension the line, cleat to keep batten pressure in the pocket, tie off the end
- Furling
- Rotate the mast counter-clockwise so the sail rolls onto the mast; furling line from the mast collar led through its cleat
- Stepping
- Insert the mast through the forward crossbar bearing into the hull until it goes all the way down and locks; pull back the mast-lock lever to remove
- Mainsheet
- Hook to the grommet in the sail with no twists in the line
- Amas
- Pivot out one at a time and lock the diagonal crossbraces; fold in against the hull for docking
Trim by condition
- Launching
- Amas out and crossbraces locked, rudder down, pedal to deeper water and drop the centreboard, check for room to manoeuvre, then point into the wind, unroll the sail and trim the mainsheet.
- Sail power
- When the luff just behind the mast flutters you lose power; pull the sail in just enough to stop the luffing. Use the points-of-sail diagram (close-hauled ≈ 45° off the wind, beam reach, broad reach, run); if caught in irons, pedal the MirageDrive out of the no-sail zone.
- Fine tuning
- Ease the sail until the telltales on both sides stream; over-sheeting stalls the sail. Re-trim whenever wind direction or course changes.
- Tacking
- From close-hauled with the boat moving, turn into the wind, ease the mainsheet a little as the boat levels head-to-wind, then straighten the rudder and sheet back in on the new close-hauled course. A rudder that feels hard to turn means the sail is over-sheeted.
- Jibing
- Turn away from the wind easing the sail slowly, sheet in as the boat nears dead downwind so the sail does not slam across, duck, keep some mainsheet tension as the sail crosses, then ease quickly on the new course. Caution in high wind — the boat is at full power and cannot be depowered without heading up.
- Reefing
- In high wind when the ama bows start to submerge, roller-reef the sail (furl part way, per the furling/unfurling page) to take load off the amas and reduce drag.
- Docking / beaching
- Furl the sail and approach under MirageDrive power; pull in the dock-side ama; raise the centreboard and rudder as depth requires; always keep the sail furled when docked or beached.
- Righting
- Fold in one ama and uncleat the mainsheet, right the hull, then roll up the sail and fold both amas out before climbing back aboard.
- No rig numbers exist for this boat; the manual's only quantitative data are the spec-sheet figures (see specs).
- Hobie Support also lists a 2021 Adventure Island Manual (Kick-Up Fins) at https://media.hobie.com/digital_assets/2021_Adventure_Island_Manual_Kick_Up_Fins.pdf (file exceeded the fetch size limit, not read) and a pre-2015 manual (adventure-island-manual_rev-e.pdf); a separate Tandem Island manual was not fetched.
- Island Spinnaker Kit instructions: https://media.hobie.com/item_attachments/Island_Spinnaker_Kit_Instructions.pdf (not read).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-04). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Hobie Mirage resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Hobie Mirage by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Hobie Mirage. Racing legality depends on your class or handicap rules; check them before changing equipment.
- Builder specificationsHobie Mirage on hobie.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Hobie Mirage part