One-design race shop · Dinghy
Club FJ / Flying Junior Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Club FJ / Flying Junior
All Club FJ / Flying Junior equipment
1 part
Fit verified for Club FJ / Flying Junior
Dynamic
Dynamic Flying Junior Dolly (Heavy)
Part # DYN-15006
$725.00
$988.64
No Club FJ / Flying Junior parts match these filters.
Can’t find a part for your Club FJ / Flying Junior? Request a Club FJ / Flying Junior part
Go fast
Club FJ / Flying Junior tuning guide
Both published guides here are North Sails guides for the Club FJ / College FJ, the US college-fleet version of the Flying Junior; no open guide for the International FJ was found, and its rig is not set up the same way, so don't apply these numbers to an International FJ. The CFJ uses a fixed rake and pre-loaded rig tension (taken on the jib halyard, measured as a change in masthead-to-transom length rather than on a gauge), so on the water trim is mostly outhaul, mainsheet/vang and jib lead.
North Sails — CFJ Tuning Guide North Sails blog page, published 5 May 2017 (updated 2026)
- Written for
- North CFJ main, jib and spinnaker
- Tension gauge
- None; rig tension is expressed as the change in the masthead-to-transom measurement
- How it’s measured
- Hoist a tape on the main halyard to the masthead and measure to the top of the transom, first with the rig leaning back on the forestay and shrouds snug, then after tensioning the jib halyard.
- Source
- North Sails, North Sails blog page, published 5 May 2017 (updated 2026)
Base setup
- Spreader length
- 16½–17½″, from where the shroud passes through the tip to where the spreader meets the side of the mast
- Mast butt
- 18–18½″ from the centreboard pin to the back of the mast extrusion
- Forestay
- In the 2nd hole back on the stem plate
- Rake, shrouds snug
- About 19′ 4″ to 19′ 6″ to the top of the transom
- Mast straightness
- Masthead to the rails directly across from each chainplate; re-adjust the shrouds if the two sides differ by more than 5/8″
- Rake with rig tension
- Tension the jib halyard until the measurement is 19′ 11″ (about 6–7″ of 'rig tension'); the leeward shroud should stay snug up to 12 mph and only go slack above that
Trim by condition
- Cunningham / main halyard
- Leave a hint of horizontal luff wrinkles nearly all the time; when overpowered tension just enough to make the luff smooth.
- Outhaul
- Light air: a hint of a crease along the foot; above 5 mph the crease should be clear; above 12 mph pull very tight for a hard crease just above the boom.
- Jib sheet
- Aim for a parallel slot; imagine a mid-leech batten parallel to the centreline. Most speed problems come from an under-trimmed jib.
- Jib lead
- Close to the middle of the track with proper rake; adjust so the luff breaks evenly. Use that position until about 10–12 mph or when overpowered, then move it aft progressively to a maximum of 2″ behind the break-even spot.
- Mainsheet
- Last 18″ of the top batten parallel to the boom (sighted from below); ease about 6″ in chop or after a tack.
- Vang
- Once overpowered, vang holds the batten parallel and bends the mast, so the sheet can be eased in puffs; more wind, more vang. Downwind keep the top batten parallel and the top telltale flowing.
- Spinnaker
- 5–8″ of luff curl; halyard about 5″ off the mast; pole ends parallel to the deck; adjust pole height by where the luff breaks.
- Wind speeds are given in mph, not knots.
- Written for the Club FJ (CFJ) and North CFJ sails, not the International FJ.
North Sails — North Sails Flying Junior Tuning Guide Older edition (northsailsod.com era; PDF created Jan 2003)
- Written for
- North FJ main and jib (Vanguard College FJ)
- Tension gauge
- Not given
- How it’s measured
- No rig measurements in this edition; refers to 'proper rake'.
- Source
- North Sails, Older edition (northsailsod.com era; PDF created Jan 2003)
Trim by condition
- Cunningham
- Always leave a hint of horizontal luff wrinkles and err on the loose side. On boats with a sliding gooseneck, tie the downhaul up to the spinnaker ring so the gooseneck can't slide down and over-tension the luff.
- Outhaul
- Same as the CFJ guide: hint of a crease in light air, clear crease above 5 mph, hard crease above 12 mph.
- Mainsheet and vang
- Top batten parallel to the boom; ease about 6″ in chop or after tacks; vang on hard when overpowered so the sheet works like a traveller. The traveller stays centred about 95% of the time.
- Jib leads
- Two layouts exist: tracks on the side decks about 8″ outboard of the seat-tank faces (most common) or on the inside vertical faces; they need different jibs. Lead near mid-track, set for an even break, then up to 2″ aft above 12 mph.
- Written for the Vanguard College FJ (the CFJ's predecessor), not the International FJ.
- Superseded by the current CFJ guide for rig numbers; kept for the side-deck vs seat-tank jib lead notes.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Club FJ / Flying Junior resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Club FJ / Flying Junior by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Club FJ / Flying Junior class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational FJ Class Rules effective 1 June 2024 (per search excerpt; not fetched)
- Class associationifjo.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Club FJ / Flying Junior part