One-design race shop · Dinghy
RS400 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS400
All RS400 equipment
9 parts
Fit verified for RS400
Selden
Selden Pop-rivet, ø4,8 X 9,9 mm, Monel, Dome Head
Part # sel-167-007-10
$45.00
Fit verified for RS400
Selden
Selden Pop-rivet, ø4,8 X 16,5 mm, Monel, Dome Head
Part # sel-167-006-05
$30.00
Fit verified for RS400
Lalizas
Lalizas Cabo Floating Rope Diam. 15/64'' (6Mm), L 98,43Ft (30M), Orange
Part # LAL-94801
$14.28
Fit verified for RS400
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
No RS400 parts match these filters.
Can’t find a part for your RS400? Request a RS400 part
Go fast
RS400 tuning guide
The RS400 has one-design sails, so its tuning guides come from top crews and the class association rather than competing sailmakers. Most guides give shroud tension in lb, but the gauges differ (Loos readings of about 28, a Superspars gauge, an electronic Harken gauge, or no gauge named), and crews measure rake and spreader length from different points (rudder mount, transom moulding or rudder housing; mast wall versus track), so check each guide's reference before copying a number.
RS400 Class Association (top 5 crews) — Rig Settings from Top 5 at 2016 RS400 National Championships 2016 (UK Nationals, Hayling Island SC)
- Written for
- Class one-design sails (not named)
- Tension gauge
- Varies by crew: Loos (28), electronic Harken (156 kg), Superspars (550 lb), or lb with gauge not named
- How it’s measured
- Rake measured from the masthead to the transom; spreader deflection from the back of the mast to a line between the shrouds. Each crew reports its own method in free text.
- Source
- RS400 Class Association (top 5 crews), 2016 (UK Nationals, Hayling Island SC)
Each crew's settings as reported (gauges differ between crews)
| Boat (crew weight) | Rig tension | Ram | Rake | Spreaders | Jib car | Wing wang (pole) |
|---|---|---|---|---|---|---|
| Boat F (136 kg) | 28 on the Loos gauge (stated as 190 kg / 420 lb), same for every setting | Neutral (about 10 mm showing) until about 20 kn, then fully forward | 6990 mm at 0–8 kn; half a hole down at 7–12 kn; another half hole at 10–12 kn+ | 395 mm long, 180 mm deflection; mast in the very back step | All the way back | Fully wanged in all conditions; dropped forward only below about 4 kn |
| Boat C (135–140 kg) | 28 on a Loos gauge on the shrouds (stated as about 190 kg / 420 lb); eased below about 4 kn at club level | About 10 mm / 5 threads showing; fully forward when really windy | 6960 mm base with pins in the 6th hole up, forward row; half a hole to 5 aft in medium; another half to 5 forward when windy | 395 mm long, 180 mm | All the way back | Fully wanged; centred only in very light air or when overstood |
| Boat A (150 kg) | 156 kg on an electronic Harken gauge | Neutral regardless of rake, wound forward to depower | 6.99 m light (hole 4 back, ram about 2 threads); 6.96 m medium (hole 4 front); 6.93 m windy (hole 5 back) | 424 mm long, 150 mm deflection | Back of track | Nearly always wanged |
| Boat D (160 kg) | 340 lb (gauge not named) | Neutral in light; max ram in medium; medium ram in heavy | 6950 mm | 410 mm | 100% aft | 100% wanged Force 1–5; centred Force 6+ |
| Boat B (143 kg) | 550 lb on a Superspars gauge, measured at eye level on the shroud | Neutral (just stopping the kicker pushing the mast forward); forward when howling | 6990 mm base in 5 kn, then half a hole back for about every 5 kn more (4 settings) | 415 mm long, 138 mm deflection; mast foot fully forward | All the way back | Max wing wang until very windy, then centred |
| Boat E (165 kg) | Not given | About halfway | Pins about halfway up the shroud plates | Not known | As far back as possible | Always pulled to windward, except centred in big waves |
Trim by condition
- Mainsheet (Boat B)
- Most crews under-sheet: sheet in until the top leech telltale collapses, then ease just enough for it to fly again, until you have to ease to stay flat.
- Crew position
- Light air: both sailors at or ahead of the shrouds. On open water the crew moves to the back of the toestraps once both are hiking; downwind, move further aft as the wind builds.
- Jib cars
- Every crew that answered sails with the cars fully aft and controls the jib leech with sheet tension instead.
- Despite the title ('Top 5'), the sheet lists six boats (A–F); it is a compilation of crews' answers, not a single guide, and their gauges and tension units differ, so the rig-tension column cannot be compared directly.
- Boat F's windy band (10–12 kn+) overlaps its medium band (7–12 kn) as written.
Jim Downer (RS Association) — RS400 Upwind Notes (Tuning explained) and Tuning Matrix 2014 (documents dated 3 June 2014)
- Written for
- Class sails; crew about 24½ st (matrix headed 155 kg)
- Tension gauge
- Gauge not named; tension in lb measured on the shrouds about 500 mm above the deck
- How it’s measured
- Set rake with 340 lb on the shrouds and the ram neutral (spins freely, mast doesn't move), measuring to the rudder mount (not the pintle). Mark this as the base and treat every other setting as an adjustment from it.
- Source
- Jim Downer (RS Association), 2014 (documents dated 3 June 2014)
Base setup
- Rake
- 6990 mm to the rudder mount, mast foot fully forward
- Mast foot
- Aft bolt in the 3rd hole from the aft end of the foot, forward bolt in the 8th
- Spreaders
- 425 mm long, 140 mm deflection
- Rig tension
- 340 lb for base measurement; normally 450 lb sailing (500 lb for a pace boost or on a lake)
- Ram
- Straight to 10 mm inverted between deck and shrouds when powered up
- Base band
- Set up for 5–12 kn, close to Nick Craig's settings
Tuning matrix by wind, crew weight 155 kg (rig tension in lb)
| Wind (kn) | Jib sheet | Mainsheet | Kicker | Cunningham | Rig tension | Ram | Outhaul | Jib luff | Jib car | Shroud hole |
|---|---|---|---|---|---|---|---|---|---|---|
| 0–5 drifting | Well eased, lots of twist; more tension with speed | In tight unless leech tufts stall | None | None | 150–200 lb, increasing with flow | Straight – 10 mm inversion | 3–4" at centre of boom | Slack | All the way aft | Base |
| 5–7 light | 2.5" off max | As close to centreline as possible with the leech alive | None | None | 340 lb | Straight – 10 mm inversion | 3–4" at centre of boom | Slack | All the way aft | Base |
| 8–14 fully powered | 1" off max, leech and luff telltales flying | Tight, 2" between blocks | Snug, increasing to spill power | None, increasing to balance | 450 lb (500 lake) | Straight – 10 mm inversion, winding on to manage power | 2" at centre of boom | Snug | All the way aft; 1 hole forward in flat sea/lake | Base |
| 14–18 overpowered | 1" off max | Tight, 1.5" between blocks 70% of the time; play in gusts | Set to manageable power | Set to balance kicker | 450 lb | All the way forward | 2" at centre of boom | Tighter | All the way aft; 1 hole forward in flat sea/lake | ½ hole down from base |
| 18–22 displacement upwind | ½" off max, easing 2–4" with the main | Tight, 1" between blocks 70% of the time | Set to manageable power | Set to balance kicker | 450 lb | All the way forward | Tight | Tight | All the way aft | 1 hole down from base |
| 22–25 | In max unless planing (then eased 3") | In max unless planing (then big eases, boat flat) | Max: pull till the main inverts, ease 1" (70–80% if a hole has been dropped) | Max | 450 lb | All the way forward | As tight as possible | Tight | All the way aft | 1 hole down if planing; 1.5 holes down in chop |
| 25–35 | Well eased, loads of twist | Well eased, about 2 ft out half the time | Max | Max | 450 lb, eased if still overpowered (re-tension before the run) | All the way forward | As tight as possible | Tight | All the way aft | 1.5 holes down from base |
Trim by condition
- Aims upwind
- Sail flat, mainsheet at its max setting, kicker off as long as possible, neutral helm. If you are at full ram, lots of kicker and easing the main more than 70% of the time, drop the shrouds half a hole (re-tension to 450 lb); another half hole at about 18 kn.
- Light air (<5 kn)
- Ease rig tension to roughly 150–200 lb (about 2.5" above the 340 lb calibration mark on the mast); no kicker; heel slightly; tighten leeches and rig tension as speed builds.
- Upwind planing (20 kn+)
- Bear away 15–20°, ease the main well and the jib about 100 mm, get the boat skipping, then point up while keeping it planing; works only with the boat flat.
- Jib
- Cars fully aft (1 hole forward in flat water), on 40 mm ratchets. Trim to just under max and play it; a ribbon about 100 mm below the top batten should be on the edge of stalling. Ease the jib a couple of inches in sync with the main in gusts.
- Kicker
- Max kicker = pull until the main inverts, then ease 1".
- Outhaul
- 2–3" between boom centre and sail normally; bar tight when windy; 3–4" when very light.
- Crew position
- Light air: crew by the mast, not on the thwart. Heavy air: crew's front leg about 6" behind the shroud.
- The matrix (https://www.rs-association.com/documents/JimDowner_TuningMatrix_4.pdf) repeats the guide's table without the jib luff and jib car columns.
- Shroud changes are not allowed while racing under class rules (as stated in the guide).
- Written for a heavy crew; lighter crews should move through the settings at lower wind speeds.
Steve Cockerill (Rooster Sailing) — Reflections of the 1st Season in the RS400 15 March 2021
- Written for
- Class sails (a new set; maker not named); crew about 140–143 kg
- Tension gauge
- Loos (reading of 28; model not stated)
- How it’s measured
- Rake tape reads 80 cm at the top of the gooseneck and is measured to the top of the GRP on the rudder gantry. Spreader length is measured from the mast track, which reads about 20 mm more than from the mast wall.
- Source
- Steve Cockerill (Rooster Sailing), 15 March 2021
Base setup
- Spreaders
- Settled on 405 mm with 140 mm deflection, then widened half a hole to about 410 mm (more offwind speed, but rake sooner)
- Rake
- 6.96 m upright (light); about 6.93 m (one pin down) for most of a windy week; others quote about 7 m in light winds
- Ram
- 5 threads showing, not moved
- Shroud steps
- Half a hole down for moderate wind and another half hole for heavy
- Rig tension
- 28 on a new Loos gauge
Trim by condition
- Gauge wear
- The plastic wheels on a Loos gauge wear and under-read; rotate them and mark the worn ones.
- Battens
- Under-tensioned battens left the main too flat; he added considerable tension to all pockets.
- Downwind
- Wing wangs too short meant the pole didn't project wide enough; check the passive line doesn't restrict the active one.
- A first-season blog post rather than a formal guide; the Loos reading isn't tied to a specific stay.
- rs400.org lists an article with the same title by Steve Cockerill (posted 24/09/2019 on that page, without a linked file); the Rooster post used here is dated 15 March 2021.
Nick Craig (RS400 Class Association) — RS400 Tuning Guide 2003
- Written for
- Class sails; rig set up for a 24+ stone crew
- Tension gauge
- Not named (lb)
- How it’s measured
- Wind bands are defined by what the crew is doing (drifting, crew not on the side deck, hiking, flat out and spilling, struggling in gusts) rather than knots, so lighter crews move up the table sooner.
- Source
- Nick Craig (RS400 Class Association), 2003
Base setup
- Spreaders
- 415 mm long, 135 mm deflection (top lighter crews use 150 mm deflection)
- Ram
- Set for a straight mast to the spreaders with the main up and 350 lb rig tension; wound forward to depower
- Jib cars
- Right back
- Mast foot
- At the front (balanced and a bit more downwind speed); lighter crews may prefer the back
Upwind, sea (rig tension in lb)
| Condition | Jib sheet | Mainsheet | Kicker | Rig tension | Outhaul | Cunningham | Mast rake | Spreaders |
|---|---|---|---|---|---|---|---|---|
| Very light (drifting) | Very little, top of leech open | Leave top of leech open | None | 200 lb | Tight but no ridge | None | 6m98 | 415 mm / 135 mm |
| Light (crew not on side deck) | More, top of leech still open | More, top of leech still open | None | 350 lb | Tight but no ridge | None | 6m98 | Same |
| Moderate (crew on side deck/hiking) | More, tightish leech | More, tightish leech | Take up slack | 350 lb | Tight | None | 6m98 | Same |
| Windy (flat out, spilling) | As hard as the crew can pull | Play it, never cleated | Some | 350 lb | Very tight | Balance kicker | 6m98 | Same |
| Very windy (struggling in gusts) | As hard as crew and helm together can pull | Play it, never cleated | Loads | As little as 150 lb | Max | Loads | 6m93 | Same |
Downwind
| Condition | Strategy | Mainsheet | Centreboard | Kicker | Outhaul | Cunningham |
|---|---|---|---|---|---|---|
| Very light | Run without the spinnaker | Long way out | Long way up | None | 2/3 off | None |
| Light | Go deep | More tension, top leech open | 1/3 up in gusts | Take up slack | Same | None |
| Moderate | Go deep | More tension, tightish leech | Down | A little, open leech | Same | None |
| Windy | High in lulls, low and planing in gusts | Play it | Down | Some, open leech | Same | None |
| Very windy | Plane as fast as possible | Play it | Down | Bit more, open leech | Same (low priority) | Same (low priority) |
Trim by condition
- Priority
- On-water controls matter more than shore settings: jib sheet first, then mainsheet, then kicker. The boat likes a lot of mainsheet.
- Kicker
- Only to depower; in very windy weather pull on until the bottom batten starts to invert, then ease until it recovers. Use cunningham to pull the draft back forward.
- Ram
- Aim to be balanced in the lulls (fully hiked, main in, flat). Overpowered in lulls: more ram; out of ram: rake further.
- Rig tension
- Ease in drifters to open the jib leech, and in very strong wind to let the mast bend and rake. Inland, up to 400 lb plus tighter leeches and flatter sails for height (hard on the boat).
- Centreboard
- Lift slightly if control is a problem in very strong wind.
- Downwind
- Bowsprit pulled fully to windward on a run; rig tension unchanged downwind.
- Older (2003) guide; current crews (2016 sheet) use shorter, more deflected spreaders and higher rig tension.
- The class page notes the guide was originally a Word file; the PDF is the hosted copy.
RS400 Class Association — Tuning Guide (class website) Posted 2001
- Written for
- Class sails
- Tension gauge
- 2001 guide: not named (lb, measured on a shroud at the same height each time); 1999 settings: Super Spar gauge (lb)
- How it’s measured
- 2001 guide: spreader length from the shroud to the mast, deflection with a straight edge across the shrouds; rake from the top of the mast to the top of the transom moulding on the centreline. 1999 settings: rake at 340 lb and neutral ram; spreader length from the nearest point of the mast to the shroud; outhaul depth from the boom (above the hoop) to the sail.
- Source
- RS400 Class Association, Posted 2001
Base setup
- Spreader length
- 395 mm (crew up to 21 st); 415 mm (over 21 st)
- Spreader deflection
- 155 mm (up to 21 st); 145 mm (over 21 st)
Rake and rig tension by wind (lb)
| Wind | Mast rake | Rig tension upwind | Rig tension downwind |
|---|---|---|---|
| Light, 0–10 kn | 7050 mm (0–15 kn) | 340 lb | 340 lb |
| Medium, 11–16 kn | 7050 mm to 15 kn; 6980 mm over 15 kn | 150–160 lb | 340 lb |
| Strong, over 16 kn | 6980 mm | 90 lb | 340 lb |
1999 National & Inland Championship winning settings (same page; rig tension on a Super Spar gauge, lb)
| Wind (Beaufort) | Mast ram | Rig tension | Mast rake | Outhaul upwind |
|---|---|---|---|---|
| 0–1.5 | Neutral | 30–100 lb (leeward shroud just slack) | 6930 mm (F0.5–1.5) | 25 mm depth |
| 2–4 | 20 mm inversion | 500 lb | 7010 mm | 25 mm depth |
| 5+ | Prebend to depower | 400 lb (mast raked, ram forward) | 6900 mm decreasing to 6860 mm | Tight |
Trim by condition
- 1999 guide extras
- Mast in the middle of the mast step; spreaders 415 mm long, 135 mm deflection; cunningham off in F0.5–3, just removing wrinkles in F4, tight in F5+; outhaul eased offwind (to the limit when planing); kicker purchase raised to 16:1; mainsheet 4:1 with 6 mm rope (block raised 2" further off the swivel in heavy air); centreboard down except on a flat-water run, when the head is raised 100 mm; tape the front 6" of the slot gasket for running downwind.
- These are text entries on the class tuning page, not separate files. The 2001 guide's rake bands (0–15 / over 15 kn) don't line up with its tension bands (0–10 / 11–16 / over 16 kn).
- The very low medium/strong tensions (150–160 lb, 90 lb) are as published and differ sharply from later guides.
Island Barn Reservoir SC — RS 400 Tips and Tricks Undated (training day with Rich Ashwell)
- Written for
- Class sails
- Tension gauge
- Not stated
- How it’s measured
- Spreader length to the mast wall; rake to the top of the GRP rudder housing.
- Source
- Island Barn Reservoir SC, Undated (training day with Rich Ashwell)
Base setup
- Spreaders
- 405 mm (415 mm for heavier crews), 140 mm depth
- Rake
- 6.98 m
- Shrouds
- Half a hole down for windy, another half hole for very windy
- Ram
- Just enough to take the kicker load
Trim by condition
- Mast
- Check it is upright.
- Short club notes from a coaching day, not a sailmaker or class guide.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
RS400 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS400 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS400 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRS Class Association Rules All Classes v4 June 2022; RS400 Class Rules (undated)
- Class associationrs400.org
- Builder specificationsRS400 on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS400 part