One-design race shop · Dinghy
Lark Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Lark
All Lark equipment
14 parts
Fit verified for Lark
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Lark
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Lark
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Lark
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Lark parts match these filters.
Can’t find a part for your Lark? Request a Lark part
Go fast
Lark tuning guide
The Lark's mast is soft (Proctor C on the older sheets, Kappa or C section on newer ones), so guides focus on rake, rig tension, spreader settings and the strut/ram that controls prebend. Current Speed and P&B guides set rake at about 21′ 9″ (Parker) or 21′ 11″ (Rondar) and North steps from 21′ 11″ to 21′ 7″, while the older Hyde and P&B sheets quote 6830–6780 mm; most guides ease tension as the wind builds, but P&B's 2025 sheet says to add it. Tension is given in lb (on the jib luff or shrouds) or as Super Spars gauge numbers, and settings differ by hull (Parker, Baker, Rondar).
Pinnell & Bax — Lark Tuning Guide 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-LAR)
- Written for
- Not stated (Pinnell & Bax guide); Kappa mast; crew weight 21 stone; Parker and Rondar hulls
- Tension gauge
- Not named for most figures (lb); one Super Spars gauge reading given (26 ≈ 300 lb)
- How it’s measured
- Rake from the top of the mast to the top of the transom; datum: tape to the top of the gooseneck black band at 18′, then measure to the top of the transom. Spreader A: from the line between spreader ends perpendicular to the mast track; B: mast side wall to spreader end.
- Source
- Pinnell & Bax, 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-LAR)
Base setup
- Spreaders (Kappa)
- A 155 mm / B 398 mm
- Rig tension, Parker hull
- About 300 lb / 26 on a Super Spars gauge
- Rig tension, Rondar hull
- Slightly less than Parker: 'approximately 280mm' as printed (read as about 280 lb)
- Mast rake, Parker hull
- 21′ 9″
- Mast rake, Rondar hull
- 21′ 11″
Mast ram
| Wind | Ram |
|---|---|
| 0–5 kn | Pulled forward from neutral to flatten the front of the main |
| 5–10 kn | Neutral |
| 10–15 kn | Pulled aft from neutral to reduce bend against the kicker and add power |
| 15+ kn | Pull to keep power, but ease when overpowered |
Trim by condition
- Rig tension
- More tension means less jib luff sag; increase as the wind builds to hold pointing.
- Rake
- As the wind increases, rake back until the boat feels controllable, keeping the same rig tension.
- Jib fairleads
- Light: pulley set fairly high so the sheet bisects the clew at 45°, sheets eased to keep the leech open. Medium: keep the 45° line by pulling the fairlead forward; more sheet for a firmer leech, top telltale breaking first. Keep moving forward as the wind builds.
- Kicker
- Use carefully on the soft mast: too much over-bends it (creases in the lower sail). Aim for the top batten stalling about 80% of the time.
- The Rondar tension is printed in mm; it is clearly meant to be lb.
North Sails — Lark Tuning Guide Posted 21 Nov 2019
- Written for
- North Lark sails; C-section or Kappa-section mast
- Tension gauge
- Not stated (lb)
- How it’s measured
- Mast foot from the aft transom to the aft face of the mast foot. Spreader length from the outside of the shroud perpendicular to the mast track's bearing surface; deflection from the middle of a line between the spreader tips to the mast.
- Source
- North Sails, Posted 21 Nov 2019
Base setup
- C section
- Mast foot 2700 mm; spreader length 395 mm; deflection 155 mm
- Kappa section
- Mast foot 2700 mm; spreader length 380 mm; deflection 145 mm
Settings by wind and sea (rig tension in lb)
| Wind & sea | 1–8 kn flat | 1–8 kn choppy | 9–15 kn flat | 9–15 kn choppy | 16+ kn flat | 16+ kn choppy |
|---|---|---|---|---|---|---|
| Mast rake | 21′ 11″ | 21′ 11″ | 21′ 9″ | 21′ 9″ | 21′ 7″ | 21′ 7″ |
| Rig tension (lb) | 330 | 330 | 297 | 297 | 264 | 264 |
| Mast ram | Pull forward to flatten the main | Pull forward to flatten the main | Pull back to keep the mast straight as kicker goes on | Pull back to keep the mast straight as kicker goes on | Pull back to ease over-bending | Pull back to ease over-bending |
| Cunningham | None | None | Take out minor creases | Take out minor creases | Lower the block a further 30 mm | Lower the block a further 30 mm |
| Outhaul | Hard | Ease 20 mm | Ease 20 mm | Ease 20 mm | Hard | Hard |
| Kicker | Take up slack | Take up slack | Top telltale flying 90% | Top telltale flying 90% | Hard | Hard |
| Centreboard | Leading edge vertical | Leading edge vertical | Raise 1–2″ | Raise 1–2″ | Raise 3–4″ | Raise 3–4″ |
Trim by condition
- Jib fairleads
- Moving them forward is like pulling the barber haulers on (opens the foot, closes the leech); aft tightens the foot and twists the head open.
- Light (1–8 kn)
- Set the sheeting pulley so the sheet bisects the clew at about 45°; keep air flowing through the slot with the upper telltales lifting before the lower.
- Moderate (9–15 kn)
- Move the fairlead forward to close the slot for maximum power; still aim for upper telltales lifting first.
- Heavy (16+ kn)
- Move forward again to hold the leech; if the main luff starts to invert, ease the sheet and move the leads back to reopen the slot.
- Spinnaker
- Clews level; ease until the luff just flickers. Tie the halyard so there's a 2″ gap from the knot to the head.
- The light-air rake cell is printed 21″ 11″ (read as 21′ 11″). Rake measuring point isn't stated.
Hyde Sails — Lark Tuning Guide – Code 2E on Proctor C Undated (class technical documents, 2008 folder)
- Written for
- Hyde Code 2E main and jib on a Proctor C mast (class lists it as also suiting Ullman and North sails)
- Tension gauge
- Not named; lb on the jib luff
- How it’s measured
- Prebend: boat on its side, main halyard to the lower black band, measure from the back of the mast to the halyard at spreader height. Jib leads: fore-and-aft from the transom to the fairlead, 400 mm up from the floor/side-tank intersection on a barber-hauler system.
- Source
- Hyde Sails, Undated (class technical documents, 2008 folder)
Base setup
- Spreaders
- Height 3100 mm; length 398 mm; deflection 155 mm (based on high hounds at 5430 mm; with low hounds aim for the prebend figures)
- Jib tack
- 85 mm off the deck
- Mast step
- 2720 mm from the back of the mast to the inside of the transom
Settings by wind (rig tension in lb on the jib luff)
| Wind | Rake (mm) | Rig tension (lb) | Prebend (ram & spreaders) | Jib fairlead (mm from transom) | Mainsheet strops |
|---|---|---|---|---|---|
| Light 0–4 kn | 6820 | 225 | 35 mm; may want to induce bend with the ram | 2170 | Long |
| Medium 5–15 kn | 6800 | 200 | 0 (careful of inversion) | 2220 | Shorter |
| Windy 16+ kn | 6780 | 175 | 25–35 mm | 2120 | Same as medium |
Trim by condition
- Light
- Flatten the sails: outhaul tight, no kicker or downhaul; long strops so the boom can be centred without closing the leech; crew forward and still.
- Medium
- Ease the outhaul slightly for depth low down; keep the mast straight (watch for inversion); minimal kicker while only sitting out, shorter strops and hard mainsheet; leech telltales flying about 90%; add kicker once both are hiking. Sail flat.
- Strong
- Rake back and open the slot; if still overpowered shorten the spreaders; limit fore-and-aft over-bend with strut, but avoid an S-bend.
- Word document; the table was read from the file's text.
Pinnell & Bax — P&B Lark Tuning Guide (Baker & Parker hulls) Undated (PDF created December 2005; class technical documents, 2008 folder)
- Written for
- Pinnell & Bax; Proctor C mast (low-rigged recommended)
- Tension gauge
- Not named (lb)
- How it’s measured
- Rake from the top of the mast to the top of the transom.
- Source
- Pinnell & Bax, Undated (PDF created December 2005; class technical documents, 2008 folder)
Base setup
- Spreaders
- Length 380 mm; angle 130 mm
- Centreboard bolt
- 2305 mm from the aft transom to the bolt centreline
- Jib leads
- 500 mm from the front of the thwart in light and heavy air, 525 mm in medium; 400 mm up from the bottom of the side tank on a barber-hauler system
- Mast heel
- 170 mm from the front bulkhead to the front step pin
- Prebend
- About 64 mm in light air (from the strut); about 26 mm natural prebend in medium
Rake and rig tension
| Conditions | Mast rake | Rig tension |
|---|---|---|
| Light | 6830 mm | 350 lb |
| Medium | 6800 mm | 375 lb |
| Heavy | 6780 mm | 230 lb |
Trim by condition
- Through the range
- Medium: maximum rig tension so the leeward shroud stays tight. As wind builds, let the mast bend fore-and-aft with the strut, rake aft and ease tension so it bends sideways, opening the slot. Strong: leeward shroud very slack; use cunningham to pull the draft forward.
- The class site labels this sheet 'Baker & Parker'; the sheet itself is headed only 'LARK'.
Pinnell & Bax — P&B Lark Tuning Guide (Rondar hull Mk2) Undated (PDF created December 2005; class technical documents, 2008 folder)
- Written for
- Pinnell & Bax; Proctor C mast (low-rigged recommended)
- Tension gauge
- Not named (lb)
- How it’s measured
- Rake from the top of the mast to the top of the transom.
- Source
- Pinnell & Bax, Undated (PDF created December 2005; class technical documents, 2008 folder)
Base setup
- Spreaders
- Length 380 mm; angle 75 mm
- Centreboard bolt
- 2320 mm from the aft transom to the bolt centreline
- Jib leads
- 2265 mm from the transom; adjustable car raised or lowered to keep all telltales streaming together
- Mast heel
- 2700 mm from the aft face of the mast to the back of the pintle
- Prebend
- About 64 mm in light air (strut); about 22 mm natural prebend in medium
Rake and rig tension
| Conditions | Mast rake | Rig tension |
|---|---|---|
| Light | 6830 mm | 300 lb |
| Medium | 6800 mm | 280 lb |
| Heavy | 6780 mm | 230 lb |
Trim by condition
- Through the range
- Same approach as the Baker/Parker sheet: strut for light-air prebend, ease tension and rake aft as it builds, cunningham in strong winds.
- The text says maximum rig tension is used in medium winds, but the table gives a lower figure for medium (280 lb) than light (300 lb).
Speed Sails (Sailboats) — Lark Tuning Guide by Sailboats Speedsails Undated web page; same numbers as the class-site PDF (file metadata October 2007)
- Written for
- Not stated (Speed Sails guide); Parker and Rondar hulls
- Tension gauge
- Not named for most figures (lb); Super Spars gauge readings given as equivalents
- How it’s measured
- Hoist the jib at the hull's tension, set the tape to 18′ at the top of the gooseneck black band, cleat, and measure to the top of the transom.
- Source
- Speed Sails (Sailboats), Undated web page; same numbers as the class-site PDF (file metadata October 2007)
Base setup
- Spreaders, Parker hull
- Length 398 mm; deflection 155 mm
- Spreaders, Rondar hull
- Length 380 mm; deflection 150 mm
- Rig tension
- Parker about 300 lb (26 on Superspar gauge); Rondar about 280 lb (24–25)
- Mast rake
- Parker about 21′ 9″ (6630 mm); Rondar about 21′ 11″ (6680 mm)
- Heavy air
- Lighter crews can drop the shrouds one hole
Mast ram
| Wind | Ram |
|---|---|
| 0–5 kn | Pulled forward to flatten the main |
| 5–10 kn | Neutral |
| 10–15 kn | Use the ram to straighten the mast |
| 15 kn – racing abandoned | Let off 1″ to bend the mast and depower |
Outhaul
| Point of sail | Outhaul |
|---|---|
| Upwind | Tight |
| Upwind, light and choppy | Eased about 1″ |
| Downwind / broad reach | Eased 2–3″ |
Trim by condition
- Jib fairleads
- Light: sheet bisects the clew at about 45° with the head quite open. Medium: move forward to stop the upper leech blowing open. Windy: further forward. Very windy: move back to open the upper leech and unchoke the slot. Treat them like a jib kicker that follows the main kicker.
- Kicker
- Slack out in light air; once overpowered, top telltale flying about 80%. The mast is very flexible: diagonal creases from the spreaders to the clew mean too much. Downwind keep the leech telltale flying.
- Cunningham
- Only when very windy; first thing off when it drops.
- Spinnaker
- Clews level reaching; head a couple of inches from the mast block; drop the pole in very light air.
- The blog's intro text recommends 470 mm spreaders (480 mm for very heavy crews), which contradicts its own table (398/380 mm) and does not appear in the class-site PDF.
- Class-site PDF copy: https://larkclass.org/web/images/media/Document/2008/Technical%20Documents/speedsail_tuning.pdf (deflection there is measured to the aft face of the mast).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Lark resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Lark by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Lark class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesLark Class Rules 2024, World Sailing Format v1.0
- Class associationlarkclass.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Lark part