One-design race shop · Dinghy
RS800 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS800
All RS800 equipment
44 parts
Fit verified for RS800
Rooster
Rooster Tiller Extension (Carbon Fibre) - Length: 7.5 ft (2300 mm) - 25 mm Dia.
Part # ROO130809
$250.20
$278.00Fit verified for RS800
Rooster
Rooster Tiller Extension (Carbon Fibre) - Length: 7.5 ft (2300 mm) - 22 mm Dia.
Part # ROO130808
$250.20
$278.00Fit verified for RS800
Selden
Selden 20 Ball Bearing Block - Single Cheek
Part # sel-402-101-13r
$23.80
$28.00Fit verified for RS800
Harken
Harken Block - Carbo 40mm Single - 90° Fixed Head
Part # HAR2659
$42.95
$48.65Fit verified for RS800
Selden
Selden 25 High Load Ball Bearing Block - Single
Part # sel-402-201-05r
$26.35
$31.00Fit verified for RS800
Selden
Selden 20 mm Ball Bearing Block - Single
Part # sel-402-101-01r
$16.15
$19.00Fit verified for RS800
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR468
$36.95
$41.50Fit verified for RS800
Harken
Harken Swivel Cam Cleat - Base (Standard) w/ Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR144
$180.95
$205.65Fit verified for RS800
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for RS800
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for RS800
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for RS800
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for RS800
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for RS800
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for RS800
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for RS800
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for RS800
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for RS800
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for RS800
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for RS800
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for RS800
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for RS800
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for RS800
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for RS800
Ronstan
Ronstan Trapeze Handles, Vertical grip - Red - Pair
Part # RONRF5122R-2
$42.16
$49.60
No RS800 parts match these filters.
Can’t find a part for your RS800? Request a RS800 part
Go fast
RS800 tuning guide
RS800 set-up is about shroud and forestay pin positions to give rake (66–67 cm by the jib-halyard method) and rig tension (23 on a Loos PT-1M on the forestay, about 30 on the shrouds), then lowers, uppers, jib tack and jib track move with the wind band. Pin holes differ from boat to boat, so the class guide shows relative changes; spreader limits changed with class rules and Selden's latest rigs have fixed spreaders.
RS800 Class Association — A guide to setting up and tuning your RS800 (with Tom Morris notes, March 2023) 2016 guide with notes added by Tom Morris, March 2023
- Written for
- Class sails, including the square-top main
- Tension gauge
- Loos PT-1M (readings marked L) and Spinlock Rig-Sense (kg)
- How it’s measured
- Rake: tape on the jib halyard, tightened until the reading to the jib track is a round number (e.g. 1 m), then measure to the bottom of the bow deck lip and take the difference. Main shroud tension and rake measured with uppers and lowers slack, sails down; lowers with main tension on and uppers slack; uppers with main and lowers on.
- Source
- RS800 Class Association, 2016 guide with notes added by Tom Morris, March 2023
Base setup
- Rake
- 66–67 cm ('upright'); raked setting in about 19 kn+: shrouds down 0.5 hole, forestay up 2–3 holes for 69–70 cm at about the same tension. TM: one rake setting of 67 cm, shrouds down half a hole above 18 kn.
- Rig tension
- 23 on a Loos PT-1M on the forestay = 140 kg on a Spinlock Rig-Sense (about 30 Loos / 220 kg on the main shrouds). TM: 24 forestay, 32 shrouds.
- Uppers
- About 14L (65 kg) max power; 12L (58 kg) if gusty; 17L (82 kg) for pointing or rig support. TM: 15 Loos all the time. Class rules limit uppers to 5:1 purchase.
- Spreaders (class rules)
- Lower: length 450–470 mm, deflection >140 mm; upper: length 355–365 mm. Max length and minimum deflection give most power. TM: 150 mm lower deflection; check older boats haven't gone past 160 mm.
Summary settings (chainplate holes counted from the top; '.5' = lower column; relative values for one boat)
| Setting | 0–7 kn | 8–14 kn | 15–18 kn | 19–24 kn | 25 kn+ |
|---|---|---|---|---|---|
| Shroud | 5.5 | 5.5 | 5.5 | 6 | 6 |
| Forestay | 6.5 | 6.5 | 6.5 | 3.5 | 3.5 |
| Lowers | 5 | 5.5 | 5 | 5 | 4.5 |
| Jib tack | 3/4 | 3/4 | 5 | 6 | 7 |
| Jib track | 3 | 2/3/4 | 4 | 5 | 6 |
| Uppers (Loos) | 14 | 14 | 14 | 14 | 17 |
Lowers (rig tension on, uppers off)
| Wind (kn) | Setting |
|---|---|
| 0–7 | Just tight (push/pull the mast a little to fit) |
| 8–14 | Tight (7 Loos) |
| 15–18 | Just tight |
| 19–24 | Some slack |
| 25+ | Some more slack |
Trim by condition
- Wind bands
- 0–7 kn drift/trundle; 8–14 underpowered; 15–18 fully powered; 19–24 overpowered; 25+ survival.
- Jib tack
- Moves down as wind increases. TM: much lower, generally 8 (2 up from the bottom) to 6 (4 up), with harder sheeting further out the track.
- Jib track
- Counted from the centre: 2/3/4 in 8–14 kn (wide if gusty/shifty/wavy, narrow to 2 in flat steady water); wider as wind builds. TM: 4 from 0–18 kn, then 5, with more sheet tension.
- Jib clew / halyard
- Centre clew hole except in survival; halyard very tight when windy (re-tension after bending the mast).
- Kicker
- Slack until nearly twin trapezing, then progressively very tight; mark at 10 cm. TM: above 20 kn back it off a little.
- Cunningham
- 8:1 continuous; slack until twin trapezing, then progressively very tight. TM: max by 16/17 kn.
- Outhaul / centreboard
- Outhaul reasonably tight, tight when overpowered; raise the board progressively when heavily overpowered.
- The 2016 text (also on forums.breizhskiff.com) gave uppers purchase as 4:1 and spreader limits of 455–465 mm/140–160 mm lower and 355–365 mm/135–155 mm upper; the 2023 class copy shows 5:1 and the newer limits.
- The 25 kn+ band is printed as '*5kn+ = survival!' in the legend.
- The uppers row is footnoted '*Square top main' in the guide's blank laminate table.
- The guide also notes Tom Morris uses the lower jib-tack holes 'between 2 and 4', which doesn't obviously match his '8 (2 up from bottom) to 6 (4 up)' comment; both are reproduced as printed.
Mike Lennon — RS 800 Tuning guide Update 4.0, 26 May 2003 (first issued 7 March 2002)
- Written for
- Original RS800 rig (pre-square-top)
- Tension gauge
- Loos spring gauge model PT-1 metric (readings used without conversion)
- How it’s measured
- Rake: tape pulled up on the jib halyard until it hits the jib sheave, measured to the bow top. Spreader deflection from the back of the mast to a line across the spreaders.
- Source
- Mike Lennon, Update 4.0, 26 May 2003 (first issued 7 March 2002)
Base setup
- Shrouds
- Hole 2 or 3 down from the top; lowers off and uppers slack; tension to 30 on the gauge (Proctor masts may be closer to hole 5)
- Forestay
- 22 on the gauge with the shrouds still at 30
- Rake
- 5757 mm (jib sheave to bow top); move the shrouds until rake and tension both match
- Lowers
- Just tight, mast straight sideways; ½–1 hole tighter for heavier crews (140–145 kg)
- Uppers
- About 10 on the gauge
- Spreader deflection
- 140 mm (140–160 now a class rule)
- Range
- Good up to 15 kn for an average 140 kg combined crew
Loos PT-1 metric scale, 3 mm wire
| Gauge reading | kg |
|---|---|
| 18 | 90 |
| 21 | 120 |
| 24 | 150 |
| 28 | 190 |
Self-tacker traveller hole (from centreline)
| Wind (kn) | Hole |
|---|---|
| 1–12 | 3 |
| 13–20 | 4 |
| 21–25 | 5 |
| Above | 6 |
Trim by condition
- Jib, 0–10 kn
- Luff slack, maybe scalloping; middle clew hole; tack about halfway up the adjusting plate; innermost traveller setting third hole from centreline.
- Jib, above 10 kn
- Move outboard and tighten the luff progressively until very tight; go wider if the boat feels 'staggery' when footing.
- Cunningham
- 8:1 continuous with the kicker; last depowering control, until it 'locks out'.
- Kicker
- Slack upwind in light air; take up slack once twin trapezing; more until diagonal creases appear, then use cunningham.
- Mainsheet
- Tie the boom blocks tight to the boom centre and use adjustable spectra strops to keep the boom on centreline.
- Written for the 2003 rule changes (fixed upper spreaders, 100% equalisation); the rake method differs from the class guide's jib-track method, so the numbers aren't comparable.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the RS800
Technical
RS800 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS800 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS800 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRS800 Int Class Rules V7, Jan 2026 (plus rule amendment approved 01/2026)
- Class associationrs800.org
- Builder specificationsRS800 on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS800 part