One-design race shop · Keelboat
H-Boat Race Shop
Everything you need to prepare, compete, and win.
Fit verified for H-Boat
All H-Boat equipment
51 parts
Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 8 in. / Aluminum / Single Hand Grip / Locking
Part # LEW29141011
$116.00
$170.95Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 10 in. / Plastic - Red / Single Hand Grip / Locking / Floating
Part # LEW29145311
$79.33
$113.95Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 10 in. / Chrome / Double Handle Grip / Locking
Part # LEW29141122
$196.00
$297.95Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 10 in. / Aluminum / Single Hand Grip / Locking
Part # LEW29141111
$125.00
$184.95Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Chrome / Single Hand Grip / Locking
Part # HARB8CL
$126.95
$181.20Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Aluminum / Speed Grip / Locking
Part # HARB8ASG
$109.95
$156.85Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Bronze / Single Hand Grip / Locking
Part # HARB8BL
$126.95
$180.90Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Aluminum / Single Hand Grip / Locking
Part # HARB10AL
$109.95
$156.85Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 8 in. / Plastic - Red / Single Hand Grip / Locking / Floating
Part # LEW29145301
$74.19
$104.95Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Chrome / Speed Grip / Locking
Part # HARB8CSG
$145.95
$208.00Fit verified for H-Boat
Lewmar
Lewmar Winch Handle - 10 in. / Chrome / Single Hand Grip / Locking
Part # LEW29141121
$153.00
$231.95Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Chrome / Single Hand Grip / Locking
Part # HARB10CL
$148.95
$212.85Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Chrome / Speed Grip / Locking
Part # HARB10CSG
$153.95
$220.15Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Aluminum / Single Hand Grip / Locking
Part # HARB8AL
$94.95
$135.00Fit verified for H-Boat
Harken
Harken Winch Handle - 8 in. / Aluminum / Ball Grip / Locking
Part # HARB8ASGLP
$106.95
$152.05Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Aluminum / Double Handle Grip / Locking
Part # HARB10ADL
$182.95
$261.50Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Bronze / Single Hand Grip / Locking
Part # HARB10BL
$193.95
$277.30Fit verified for H-Boat
Harken
Harken Winch Handle - 10 in. / Aluminum / Speed Grip / Locking
Part # HARB10ASG
$124.95
$177.55Fit verified for H-Boat
Premium Ropes
Anchor Line - 12 mm (1/2 in) Polyester 3-Strand, by Premium Ropes
Part # PRR-201-12-BLK
$1.08
$1.27Fit verified for H-Boat
Lewmar
Lewmar Rode - 10' 1/4"G4-125'1/2"8Plt W/Shkl
Part # LEWHM10HT125PX
$352.00
$531.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 20'1/4"G4 100'1/2"3 Str Skl
Part # LEWHM20HT100X
$244.00
$371.95Fit verified for H-Boat
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (5'), 1/2 in 3-Strand Polyster (100')
Part # LEW69000331
$215.00
$325.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 10'1/4"4G 150'1/2"3Str Swv/Skl
Part # LEWHM10HT150XS
$243.00
$366.95Fit verified for H-Boat
Nautalytics
Nautalytics Mast Mount Compass (Digital Compass)
Part # NTL-MASTMOUNT
$500.00
Fit verified for H-Boat
Layline
Layline Canvas Shop Mainsail Cover - MZ for booms up to 11.5 ft (3.5 m)
Part # MPC-MZ35-ANV
$518.00
$678.48Fit verified for H-Boat
Lewmar
Lewmar Rode - 10' 1/4"G4-100' 1/2"8Pltw/Shkl
Part # LEWHM10HT100PX
$219.00
$330.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 10' 1/4"G4 100' 1/2" Str& 5/16
Part # LEWHM10HT100X
$242.00
$364.95Fit verified for H-Boat
Powerwinch
Powerwinch 200' of 1/2" Rope 15'of 1/4" HT Chain Rode
Part # pow-p10294
$457.00
$479.22Fit verified for H-Boat
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (15'), 1/2 in 3-Strand Polyster (200')
Part # LEW69000334
$363.00
$567.95Fit verified for H-Boat
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 150' long
Part # buc-cro-nal12150
$122.00
$123.70Fit verified for H-Boat
Powerwinch
Powerwinch 150' of 1/2" Rope 10' of 1/4" HT Chain Rode
Part # pow-p10293
$381.00
$403.92Fit verified for H-Boat
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (10'), 1/2 in 8-Plait Nylon (200')
Part # LEWHM10HT200PX
$469.00
$735.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 150' 1/2"8Plt Splcd 5/16" Skl
Part # LEWHM150PX
$329.00
$498.95Fit verified for H-Boat
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 200' long
Part # buc-cro-nal12200
$161.00
$169.04Fit verified for H-Boat
Lewmar
Lewmar Rode - 10' 1/4"G4 150"1/2"8Plt W/Shkl
Part # LEWHM10HT150PX
$382.00
$597.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 15'1/4"G4 200'1/2"8P Jj Swiv
Part # LEWHM15HT200PS
$372.00
$582.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 10'1/4"G4-200'1/2"8Pltw/Shkl&S
Part # LEWHM10HT200PXS
$493.00
$769.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 15' 1/4"G4 200' 1/2" 8P W/5/16
Part # LEWHM15HT200PX
$495.00
$773.95Fit verified for H-Boat
Lewmar
Lewmar Rode - 6' 1/4" G4 150' 1/2" 8 Plt Rop
Part # LEWHM06HT150P
$358.00
$561.95Fit verified for H-Boat
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (10'), 1/2 in 3-Strand Polyster (150')
Part # LEW69000332
$289.00
$435.95Fit verified for H-Boat
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for H-Boat
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for H-Boat
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for H-Boat
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for H-Boat
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No H-Boat parts match these filters.
Can’t find a part for your H-Boat? Request a H-Boat part
Go fast
H-Boat tuning guide
H-Boat guides fix the mast foot from the forestay pin, set rake and spreader sweep, then give upper/lower shroud tensions for three wind bands on a Loos PT-1-type gauge (North names the PT-1 M); jib sheeting is read off tape marks on the spreaders. North and Høj Jensen publish different numbers and measure rake differently, North's Danish and English editions differ in a few set-up figures, and Høj Jensen's Dutch edition adds settings for narrow spreaders.
North Sails — H-Boat Tuning Guide Undated web guide (Steffen Stegger, Lars Christiansen, Theis Palm); tension table image uploaded 2017
- Written for
- North H-Boat mainsail, jib and GRADIENT spinnaker
- Tension gauge
- Loos PT-1 M
- How it’s measured
- Before stepping, pull the uppers (outside the spreader tips) and forestay up the mast and mark all three at the black gooseneck mark. Rake is the forestay mark to the deck, measured along the forestay; centring compares the upper-shroud marks to deck on each side.
- Source
- North Sails, Undated web guide (Steffen Stegger, Lars Christiansen, Theis Palm); tension table image uploaded 2017
Base setup
- Spreader length
- 81 cm, side of the mast to where the shroud crosses, along the middle of the spreader
- Spreader sweep
- 19 cm from a line between the uppers to the aft side of the mast
- Spreader tape marks
- 44 cm and 54 cm from the side of the mast (jib trim references)
- Mast foot
- 2,42 m from the centre of the forestay pin to the front edge of the mast
- Gooseneck mark
- 54,8 cm from the top of the mark to the deck, along the side of the mast (correct any difference via the forestay in the rake step)
- Mast rake
- 1,37 m from the forestay mark to the deck, along the forestay
- Mast step
- Mast must bear on its full footing, or the rig pressure varies and the forestay is unsteady
- Lowers in breeze
- Mast straight up to 20–22 kn; above that tighten until the mast falls 5–10 cm to leeward at the forestay fitting (depends on crew weight)
Rig tension (Loos PT-1 M)
| Wind | Wind speed (m/s) | Upper shrouds | Lower shrouds |
|---|---|---|---|
| Light | 0–2 | 26 | 19 |
| Medium | 3–9 | 36 | 33 |
| Heavy | 10+ | 40 | 38 |
Mainsail and jib by wind
| Control | Light | Medium | Strong |
|---|---|---|---|
| Outhaul | 0–4 kn: 3 cm from the mark | 4–10 kn: about 1,5 cm from the mark | To the mark |
| Cunningham | Off | Just remove wrinkles | Above 14 kn: pull hard |
| Jib sheet (leech to spreader mark) | Under 6 kn: 54 cm mark | Inner 44 cm mark | Inner 44 cm mark |
| Jib lead | Under 6 kn: up to 5 holes forward | Base: 2,88 m from forestay pin to block centre | Big waves above 6 kn: 1–2 holes forward |
Trim by condition
- Mainsheet
- Main control: harder closes the leech, adds helm and pointing (medium wind, flat water if you can keep the boat flat); light air ease so the top-batten telltale flies straight back; heavy air sheet very hard and add backstay until light on the helm; more twist in waves. Aft part of the top batten parallel to the boom in all winds.
- Traveller
- Keep the boom parallel to the centreline for as long as possible (widest gap between main and jib); as wind builds and backstay goes on, let the traveller down to leeward until balanced; depends on crew weight.
- Backstay
- Flattens and opens the main and reduces forestay sag; marked every 5 cm.
- Kicker
- Upwind only in heavy air (bends mast, opens the lower sail); never upwind under 16 kn; ease before running; reaching, set so the top batten is parallel to the boom.
- Jib halyard
- Only until creases disappear; leave some luff creases in light air.
- Spinnaker
- Pole fitting 1,50 m above the cabin-top roof; pole horizontal in most conditions; light air adjust so the clews are level; heavy-air tight reach never closer than 60 cm to the forestay.
- The tension table is an image with wind in m/s, while the rest of the English guide uses knots.
- The page's jib-lead paragraph is repeated under the halyard heading.
- The old URL northsails.com/sailing/en/resources/h-boat-tuning-guide redirects to the blog URL above.
North Sails — H-Båd Tuning Guide (Danish edition) Undated blog guide (Theis Palm); in Danish
- Written for
- North H-Boat mainsail, jib and spinnaker
- Tension gauge
- Loos PT-1 M (spelled 'Loose Gauge type PT-1 M')
- How it’s measured
- Same procedure as the English guide (marks on uppers and forestay at the top of the black gooseneck band; rake measured parallel to the forestay; centring from the upper-shroud marks to deck, which the guide says is more precise than measuring from the masthead). Wind in m/s throughout.
- Source
- North Sails, Undated blog guide (Theis Palm); in Danish
Base setup
- Spreader length
- 83 cm, side of the mast to the wire in the spreader tip, along the middle of the spreader (English edition: 81 cm)
- Spreader sweep
- 19 cm, string between the uppers to the aft edge of the mast
- Spreader tape marks
- 44 cm and 55 cm from the side of the mast
- Mast foot
- 2,42 m, forestay pin centre to front of mast
- Gooseneck mark
- 54,8 cm, top of the black mark to deck along the side of the mast
- Mast rake
- 1,37 m, forestay mark to deck parallel to the forestay
- Mast step
- Mast should rest on its whole footing, or rig pressure varies and the forestay is unsteady
- Lowers in breeze
- Mast straight up to 10 m/s; then tighten until it falls 5–10 cm to leeward at the forestay fitting (crew weight). The lower-shroud numbers are only a guideline from the authors' own boat.
Rig tension (Loos PT-1 M) – separate image, same values as the English edition
| Wind | Wind speed (m/s) | Upper shrouds | Lower shrouds |
|---|---|---|---|
| Light | 0–2 | 26 | 19 |
| Medium | 3–9 | 36 | 33 |
| Heavy | 10+ | 40 | 38 |
Mainsail and jib by wind (m/s)
| Control | Light | Medium | Strong |
|---|---|---|---|
| Outhaul | 0–2 m/s: 3 cm from black mark | 2–5 m/s: 1,5 cm from black mark | Over 5 m/s: to the mark |
| Cunningham | Off | Just remove luff wrinkles | Over 7 m/s: pull hard |
| Jib sheet | Under 3 m/s: outer 54 cm mark | Over 3 m/s: inner 44 cm mark | Inner 44 cm mark |
| Jib lead | Under 2 m/s: up to 5 holes forward | Base 2,88 m forestay pin to block centre | Lots of sea and over 3 m/s: 1 hole forward |
Trim by condition
- Mainsheet
- Hard sheeting closes the leech, adds helm and height (medium wind, flat water, if the boat can be held flat); light air ease until the top-batten telltale flies aft; heavy air sheet in and pull backstay until light on the helm; more twist in bigger waves. Aft half of the top batten parallel to the boom in almost all winds.
- Traveller
- Pull the car to windward so the boom stays on the centreline as long as possible; once the backstay is fully on, let it down to leeward until balanced; depends on crew weight.
- Backstay
- Flattens and opens the main and reduces forestay sag; marked every 5 cm.
- Kicker
- Never upwind below 8 m/s, and then with care; ease to the running position before bearing away; otherwise set so the aft half of the top batten is parallel to the boom on reaches and runs.
- Jib halyard
- Only until the creases at the hanks disappear; small creases are fine in light air.
- Spinnaker
- Pole fitting 1,50 m above the coachroof; pole horizontal in most conditions; light air level clews; above 7 m/s set the leeward barberhauler; never closer than 60 cm to the forestay on a hard-air tight reach.
- Real differences from the English edition: spreader length 83 vs 81 cm; outer tape mark 55 vs 54 cm (the Danish jib section itself still says 54 cm); lead in big seas 1 hole vs 1–2 holes forward; light-air lead threshold under 2 m/s (about 4 kn) vs under 6 kn; leeward barberhauler above 7 m/s appears only here; author Theis Palm only.
- Other wind limits are just unit changes and roughly equivalent: lowers straight to 10 m/s (about 19 kn) vs 20–22 kn; kicker 8 m/s (about 16 kn) vs 16 kn; cunningham 7 m/s vs 14 kn; outhaul 0–2/2–5 m/s vs 0–4/4–10 kn; jib sheet and chop threshold 3 m/s vs 6 kn.
- Translated from Danish (overvant = uppers, undervant = lowers, forstag = forestay, hækstag = backstay).
Høj Jensen Sails — H-Boat Trim Guide Current web page (undated); described as the result of five years of sail and rig testing
- Written for
- Høj Jensen mainsail, light jib, medium/hard jib, spinnaker
- Tension gauge
- PT-1 (sold by Høj Jensen Sails)
- How it’s measured
- Rake is measured from the main halyard at the hook to the transom (not along the forestay). Mast centred with a tape on the main halyard, zeroed at the black band at the top of the mast, to reference points on each side of the toerail.
- Source
- Høj Jensen Sails, Current web page (undated); described as the result of five years of sail and rig testing
Base setup
- Mast position
- 2,41 m from the forestay bolt to the front edge of the mast foot
- Spreader marks (jib)
- Inner 40 cm from the mast (light/medium); outer 45,5 cm (hard wind)
- Spreader sweep
- With long spreaders (83 cm), 19–21 cm from the back of the mast to an elastic between the shrouds
- Mast rake
- 10,34 m, main halyard at the hook to the transom
- Mast step
- Mast foot should bear only on its sides, not front or back edges
- Jib tack
- Shackle between 4,5 cm and "6 5 cm" (garbled in source) to the tack, with a second shackle round the forestay so the tack ring can't move
- Jib lead
- Medium jib 287 cm, light jib 286 cm, from the forestay to the middle of the sheet block
Shroud tension (PT-1)
| Wind | Upper shroud | Lower shroud |
|---|---|---|
| Light 0–4 m/s | 33 | 28 |
| Medium 3–8 m/s | 37 | 33 |
| Hard 7–17 m/s | 39 | 36 |
Traveller, cm to windward of centre
| Wind (m/s) | 0–2 | 1–3 | 3–4 | 4–6 | 6–10 | Over 10 |
|---|---|---|---|---|---|---|
| Traveller | 14–16 | 14 | 12 | 6 | 4 | 0 |
Outhaul, eased from the tape mark
| Wind (m/s) | 0–2 | 2–3 | 3–5 | 4–8 | Over 7 |
|---|---|---|---|---|---|
| Ease | 4,5 cm | 3,5 cm | 2 cm | 1 cm | 0 cm |
Trim by condition
- Mainsheet
- Last 40 cm of the top batten parallel to the boom; once up to speed, a touch harder to point. Light air and chop: parallel or very slightly hooked to windward. In light and medium air the top leech telltales should be hidden behind the main (stalled) about 80% of the time; if they fly all the time, sheet harder.
- Heel and backstay
- Keep about 6–10° heel; backstay needed continuously from 4 m/s. In breeze sail flat with more and more backstay; mark it.
- Traveller
- Car to windward in almost all conditions; in light and medium air the boom sits right over the centreline; don't play the traveller in gusts – use backstay and mainsheet and keep the car at the table numbers upwind.
- Outhaul
- Looser for helm, pointing or chop; tighter for less helm and top speed in gusts or flat water.
- Cunningham
- Max draft no further aft than 50%; often not needed; if used, only from 4–5 m/s and just to remove luff wrinkles.
- Jib sheet
- Middle batten parallel to centreline; in light/medium air the leech level with the inner spreader mark; in hard wind, when speed drops and helm builds, let the leech out to the 45 cm mark. Lead back 1–2 cm to sail lower/faster, 2 cm forward to point.
- Jib halyard
- Only until luff wrinkles slowly smooth out; never over-stretch the luff.
- Hard weather (over 12 m/s)
- Traveller to centre, mainsheet as hard as possible, then kicker very hard, then ease the sheet back to normal; the kicker bends the mast and flattens the lower main.
- Reaching
- Kicker so the last 40 cm of the top batten is parallel to the boom; ease cunningham and backstay; pole height for level clews; above 7 m/s both barberhaulers tight; windward barberhauler always on.
- Lowers
- If the boat feels dead upwind in waves, ease the lowers slightly for more jib entry.
- Crew
- Helm behind the traveller with crew close by, hiking hard; in very light air one crew can sit in the cabin upwind.
- The shroud, traveller and outhaul tables use overlapping wind bands as published (e.g. 0–4 / 3–8 / 7–17 m/s).
- The hard-wind jib note refers to a '45 cm mark' while the set-up gives the outer mark as 45,5 cm.
- A PDF titled 'hoy-jensen-h-bat-trimguide' on media.h-boat.se returned HTTP 403 (re-tried at audit) and wasn't opened, so it may differ; the text above is from Høj Jensen's own page. Translated from Danish.
Høj Jensen Sails — Trim Guide NL (H-Boat) Undated web page; Dutch translation by Team NED 85 with Høj Jensen's support, which says it mixes the original with the team's own interpretation (it cites 15 years of testing)
- Written for
- Høj Jensen mainsail, light/medium jib, spinnaker
- Tension gauge
- PT-1 (sold by Høj Jensen Sails; written 'PTU' in the tables)
- How it’s measured
- As the Danish guide: rake from the main halyard at the hook to the transom corner, mast centred with a tape on the main halyard zeroed at the black band at the masthead. Adds an alternative rake check along the forestay from the deck.
- Source
- Høj Jensen Sails, Undated web page; Dutch translation by Team NED 85 with Høj Jensen's support, which says it mixes the original with the team's own interpretation (it cites 15 years of testing)
Base setup
- Mast position
- 2,40–2,41 m from the forestay bolt to the front of the mast foot
- Spreader marks (jib)
- Inner 40 cm (light/medium; the light jib is sailed on this mark), outer 45,5 cm (hard wind)
- Spreader sweep
- Long spreaders (83 cm): 19–21 cm from the back of the mast to an elastic between the shrouds; short spreaders about 17 cm
- Mast rake
- 10,34 m, main halyard at the hook to the transom, for light-wind conditions; boat-dependent
- Forestay rake check
- Standard 1,37 m from the deck/plate to the top of the band mark on the forestay; may vary between boats towards 1,35 m
- Jib tack
- Shackle 4,5–6,5 cm long, with a second shackle round the forestay
- Jib lead
- Medium jib 287 cm, light jib 286 cm, centre pin to centre of the block (block upright)
Shroud tension, 83 cm spreaders (PT-1, uppers – lowers)
| Wind | Uppers | Lowers | Jib |
|---|---|---|---|
| 0–8 kn / 0–4 m/s | 33 | 28 | Light |
| 9–16 kn / 3–8 m/s | 37 | 33 | Medium |
| Over 17 kn / 7–17 m/s | 39 | 36 | Medium |
Shroud tension, narrow spreaders as used on NED 85 (PT-1, uppers – lowers)
| Wind | Uppers | Lowers | Jib |
|---|---|---|---|
| 0–8 kn / 0–4 m/s | 35 | 30 | Light |
| 9–16 kn / 3–8 m/s | 39 | 35 | Medium |
| Over 17 kn / 7–17 m/s | 41 | 38 | Medium |
Traveller, cm to windward of centre
| Wind (kn) | Wind (m/s) | Traveller |
|---|---|---|
| 0–4 | 0–2 | 14–16 |
| 2–6 | 1–3 | 14 |
| 6–8 | 3–4 | 12 |
| 8–12 | 4–6 | 6 |
| 12–19 | 6–10 | 4 |
| Over 19 | Over 10 | 0 |
Outhaul, eased from the maximum point
| Wind (kn) | Wind (m/s) | Ease |
|---|---|---|
| 0–4 | 0–2 | 4,5 cm |
| 4–6 | 2–3 | 3,5 cm |
| 6–9 | 3–5 | 2 cm |
| 8–16 | 4–8 | 1 cm |
| Over 16 | Over 10 | 0 cm |
Trim by condition
- Narrow spreaders, hard wind
- Wind the uppers up until the forestay reads 30/32 on the PT-1, then the uppers read 41 (as written for NED 85).
- Mainsheet
- Last 40 cm of the top batten parallel to the boom; slightly harder to point once up to speed. Top leech telltales hidden behind the main about 80% of the time in light and medium air. Keep 6–10° heel, using the backstay continuously from 4 m/s (8 kn).
- Traveller
- Boom just over the centreline in light and medium air, car brought gradually towards centre as wind rises; don't play it in gusts – use backstay and mainsheet.
- Outhaul (simple version)
- Light air about 5 cm from the band, medium about 3 cm, hard weather fully out. If the foot is cut shorter the band may not be reachable, so use a different maximum point.
- Cunningham
- Draft at most 50% aft; often not used; if used, from 4–5 m/s and only to remove luff wrinkles.
- Jib sheet
- Middle batten parallel to the centreline; in light and moderate air the leech by the inner spreader mark; in hard wind with falling speed and rising helm, out to the 45 cm mark. Lead back 1–2 cm to sail lower/faster, 2 cm forward to point higher.
- Downwind
- Top batten (last 40 cm) parallel to the boom; cunningham and backstay off; pole for level clews; above 7 m/s (4 Bft / 14 kn) both barberhaulers on; windward barberhauler always on.
- Hard weather (over 12 m/s)
- Traveller to centre, sheet in hard, kicker very hard, then ease the sheet back to normal.
- This is a third-party translation hosted on Høj Jensen's site; it states the content is partly the translators' own interpretation, and its numbers differ in places from the Danish page (mast position 2,40–2,41 vs 2,41 m; extra narrow-spreader tensions and forestay rake check).
- Knot conversions are as printed and are not always consistent with the m/s bands (e.g. outhaul 'over 16 kn' paired with 'over 10 m/s', where the Danish page has 'over 7 m/s').
- Translated from Dutch.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
H-Boat resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the H-Boat by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current H-Boat class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesH-Boat Class Rules 5 Aug 2022 (hbt_cr_20220805.pdf)
- Class associationh-boat.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a H-Boat part