One-design race shop · Keelboat

VX One Race Shop

Everything you need to prepare, compete, and win.

Shopping for

VX One

  • 73 verified parts
  • 18 brands
  • Fit checked Nov 2026

Fit verified for VX One

All VX One equipment

73 parts

Can’t find a part for your VX One? Request a VX One part

Official Harken dealer

VX One deck layout

LOA
19′/5.79 m
LWL
18.83′/5.74 m
Beam
7.17′/2.19 m
Sail Area Main + Jib
215 sq ft./19.97 sq m.
Sail Area Gennaker
280 sq ft./26 sq m.
Draft, keel down
4.33′/1.32 m
Crew Weight tolerance
380 – 450 lbs (2-3 person)

Hoistable Swivel and Furler

Hoistable Swivel and Furler — Harken layout for the VX One
Drawing: Harken
  1. 1 40mm T2™ Loop Soft-Attach BlockHarken 2148 $51.95
  2. 2 40mm T2™ Loop Soft-Attach BlockHarken 2148 $51.95
  3. 3 57mm Ratchet Block — SwivelHarken 2135 $86.95
  4. 4 40mm T2™ Loop Soft-Attach BlockHarken 2148 $51.95
  5. 7 40mm Ratchet Block — SwivelHarken 2608 $72.95
  6. 8 Standard Carbo-Cam® CleatHarken 365 $34.95
  7. 9 40mm T2™ Loop Soft-Attach BlockHarken 2148 $51.95

Micro Track and Self-Tacking Jib

Micro Track and Self-Tacking Jib — Harken layout for the VX One
Drawing: Harken
  1. 1 29mm 90-Degree BlockHarken 352 $23.95
  2. 2 29mm 90-Degree BlockHarken 352 $23.95
  3. 3 13mm Car — Pivoting ShackleHarken 2700 $150.95
  4. 5 Standard Low Profile Cam Base — SwivelHarken 205 $163.95
  5. 6 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  6. 7 40mm Fiddle Block — Swivel, BecketHarken 2656 $58.95
  7. 8 29mm Stand-up BlockHarken 349 $26.95
  8. 9 29mm Stand-up BlockHarken 349 $26.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

VX One tuning guide

The VX One is tuned with cap shrouds, intermediates (diagonals) and check stays, changed in steps of turns from a base set on the dock; on the water the leeward cap should just go slack upwind and the main's overbend wrinkles show whether the intermediates and checks are right. North's base is on a Loos PT-1 (28/18/11, or 30 on the caps for CST masts), while Quantum's chart quotes '#250 PT-2' and a separate 'V1 26, D1 18' base, so don't mix the two.

North Sails — VX One Tuning Guide (with VX One Speed Guide) 2021-22 update (North blog, 27 December 2021: check-stay steps added); current web page

Written for
North VX One main, self-tacking jib and spinnaker (polyester one-design inventory)
Tension gauge
Loos PT-1
How it’s measured
Check stays slack while setting caps and intermediates; then tension the check stays and read them with the gauge on the intermediate shroud. Prebend: main halyard pulled taut to the gooseneck, gap at the spreaders. Centre the mast with a tape on the jib halyard to matching marks on each sheer line just forward of the shrouds.
Source
North Sails, 2021-22 update (North blog, 27 December 2021: check-stay steps added); current web page

Base setup

Mast step
Mast butt pinned in the 3rd hole from the aft end (check class rule C.9.3)
Caps (base, 8–10 kn)
28 on PT-1 (Southern Spars mast); 30 on PT-1 for CST masts
Intermediates (base)
18 on PT-1
Check stays (base)
About 11 on PT-1
Prebend
Close to 2.25″ at the spreaders
Jib clewboard
4th hole from the bottom (5th in lighter air, 3rd in heavier)
Crew weight
Chart for 430 lb (Speed Guide: class norm about 420 lb, results from 380–450 lb)

Rig tune by wind (turns from base; base on Loos PT-1)

Wind (kn)Cap shroudsIntermediate shroudsCheck stays
0–8−2−1−0.5
8–10 (base)Base (28 on PT-1)Base (18 on PT-1)Base (11 on PT-1)
10–12210.5
12–14421
14–16631.5
16–18842
18–201052.5
20–221263
22+1473.5

Jib car angle

Sheeting angleDistance from centreline
5°193 mm
Sweet spot260 mm
7.5°290 mm
10°386 mm

Trim by condition

Shrouds on the water
Set the caps so the leeward upper just starts to look slack; more than about ½″ of wiggle, tighten both equally; no wiggle, ease both. Speed Guide: about 18 turns on the caps and about 10 on the diagonals from light to really windy; checks should only need 1–2 turns over the whole range.
Intermediates and checks
Over-trim the main 3–5 clicks: overbend wrinkles should start just below the spreaders and run about 50% of the way to the clew. Starting above the spreaders = intermediates too loose; well below = too tight. Running further than 50% = checks/intermediates too loose; only 30–40% = too tight. Ease the cunningham to see them in breeze.
Mainsheet
Top batten parallel to the boom, top telltale stalling about 75% of the time; cock it slightly to windward to point once up to speed. Light air and chop: top batten 5–7° open with no vang. Heavy air: use the sheet to hold heel under 5°.
Outhaul
Heavy air 1–2 finger widths between boom and mid-foot; chop or power needed about 3 fingers; downwind 4–4.5 fingers.
Cunningham
Very little up to 10 kn; 11–12 kn remove many wrinkles; above 12 kn progressively to a smooth luff; draft 40–50% aft. Off downwind.
Vang
Just snug until consistently heeling more than 5–7°, then tighter the further the boom is eased. Downwind ease so the leech telltales fly all the time, more ease in more wind.
Jib
Middle batten parallel to centreline; 5–7° outboard in light or sloppy conditions and eased for twist in breeze; leech telltale flying but about to stall. Car up so the main just starts to backwind (about 5–7° in light air); 2–3° lower in breeze. Speed Guide: car at 7–7.5° until depowering, then halfway down (10–13°). Halyard: slight wrinkles back to the first radial panel in light–medium air, gone at about half vang, then progressively harder.
Spinnaker
3–4″ of luff curl; play constantly in light air; sail a constant apparent wind angle.
Heel and weight
Upwind 5–7° leeward heel, windward jib telltale at about 45°. Downwind 5–10° heel (Speed Guide: about 8°, enough to lift half the hull, similar to upwind); in planing breeze keep the bow 4–6″ out of the water. Speed Guide: displacement mode under 10 kn, planing above.
  • The text says the chart follows a 2:1 cap:intermediate ratio that becomes 1:1 above 19 kn, but the published table keeps 2:1 all the way to 22+.
  • The text says the lightest settings should be 2 steps down from base; the chart shows only one step (0–8 kn) below base.
  • The text also says the uppers should be '3–4 steps up' in 19–20 kn, which doesn't match the chart's 18–20 kn row (5 steps, +10 turns).
  • Speed Guide (Mike Marshall, undated): https://www.northsails.com/sailing/en/resources/vx-one-speed-guide; 2021-22 update: https://www.northsails.com/blogs/north-sails-blog/vx-one-2021-22-winter-update

Quantum Sails — VX One Tuning Guide Undated chart (PDF created July 2020)

Written for
Quantum VX One sails
Tension gauge
The chart's base row says '#250 PT-2'; the footnote gives a base gauge reading of V1 26, D1 18 without naming the gauge
How it’s measured
Turns from base; the chart has blanks to record turnbuckle measurements (mm) at base for port and starboard uppers and lowers.
Source
Quantum Sails, Undated chart (PDF created July 2020)

Base setup

Base (10 kn)
Uppers #250 PT-2; lowers 'tight +1'
Base gauge
V1 26, D1 18
Check stay base
Firm + 0.5 turn
Jib traveller marks
9″, 10″, 11″

Turns from base by true wind

TWS (kn)UppersLowersJib lead (hole)Jib traveller (inches to leeward)
4−6−3Centre
6−4−2.5Centre
8−2−1Centre
10#250 PT-2Tight +1Centre11″
1210.5Centre
1421Centre
1631.5Centre
18421 down
20+52.51 down
  • '#250' on a PT-2 and 'V1 26' can't both be the same gauge scale; ask Quantum which applies before using these as absolute readings. The turn steps are usable on their own.
  • Only the 10 kn row has a jib-traveller figure.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the VX One

Technical

VX One resource centre

How we verify parts

Fit verified
Each part listed here was matched to the VX One by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current VX One class rules before changing equipment, and ask your class measurer if a part is not original equipment.