One-design race shop · Dinghy
Finn Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Finn
All Finn equipment
19 parts
Fit verified for Finn
Harken
Harken Cam Cleat - Carbo-Cam 365 (Standard) - Line: 1/8 to 3/8 in (3 to 10 mm)
Part # HAR365
$34.95
$40.10Fit verified for Finn
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR468
$36.95
$41.50Fit verified for Finn
Harken
Harken Cam Cleats - Standard Fairlead (Black) - For Carbo-Cam 365
Part # HAR425B
$8.95
$9.65Fit verified for Finn
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Finn
Sea-Dog
Sea-Dog Poly Pro Anchor Line w/Snap - 3/8" x 75' - Yellow
Part # SDG-304210075YW-1
$27.83
$28.85Fit verified for Finn
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for Finn
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Finn
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Finn parts match these filters.
Can’t find a part for your Finn? Request a Finn part
Official Harken dealer
Finn deck layout
- LWL
- 4.2 m, 14 ft
- LOA
- 4.5 m, 14 ft 9 in
- Beam
- 1.51. m, 4 ft 10 in
- Hull (with fittings)
- 140 kg, 319 lb
- Sail Area
- 10 sq m, 115 sq. ft
- Rig Type
- Cat
Hiking Strap Adjustment
-
5
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
6
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
7
Standard Carbo-Cam® CleatHarken 365
$34.95 -
10
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
11
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
12
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
13
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
14
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
15
Standard Carbo-Cam® CleatHarken 365
$34.95 -
16
Standard Carbo-Cam® CleatHarken 365
$34.95 -
17
Standard Flairlead — BlackHarken 425B
$8.95 -
18
Standard Carbo-Cam® CleatHarken 365
$34.95 -
19
Standard Flairlead — BlackHarken 425B
$8.95 -
20
Micro Cam-Matic® CleatHarken 468
$36.95 -
21
Micro Cam-Matic® CleatHarken 468
$36.95 -
22
29mm T2 Soft-Attach BlockHarken 2146
$29.95
Mainsheet (side view)
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Finn tuning guide
Finn tuning is mainly mast rake (or, better, leech tension measured with a spring or digital gauge), deck chocks to balance the helm, centreboard fore-and-aft position, and inhaul/outhaul/cunningham trim. Leech-tension numbers depend on the gauge, the 6020 mm reference length and the sail cut, and tape-rake numbers depend on the measuring points, so don't mix figures between guides.
North Sails — Finn Tuning Guide 2017 PDF (created August 2017)
- Written for
- North Sails Finn mainsails: Technora radial and Maxx cross-cut
- Tension gauge
- Spring or digital leech-tension gauge (Persola spring balance or Devoti digital strain gauge); readings in lb / kg
- How it’s measured
- Leech tension rather than tip-to-transom rake: hook the gauge and a long tape on the main halyard and hoist to the lock; hook the gauge onto the outhaul; tie the traveller down; sheet the boom to the deck with the boom end at the side of the boat (always the same side); adjust the outhaul until the tape reads 6020 mm to the inner edge of the boom black band; read the gauge.
- Source
- North Sails, 2017 PDF (created August 2017)
Base setup
- Leech-tension reference length
- 6020 mm, halyard lock to inner edge of the boom black band
- Adjustment
- Move the deck chocks or the mast-heel screw; about 1 mm of chock = 1 lb (1 cm of rake). Re-check after every change.
- Spare chocks
- Carry at least five 1 mm chocks for fine-tuning on the water
Settings by true wind speed (leech tension on a spring/digital gauge)
| Setting | 0–8 kn | 8–12 kn | 12–16 kn | 16–20 kn | 20+ kn |
|---|---|---|---|---|---|
| Deck (chocks) | 30 mm | 40 mm | 50 mm | 55 mm | 55 mm |
| Leech tension, Technora radial sail | 73 lbs / 33 kg | 75 lbs / 34 kg | 75 lbs / 34 kg | 74 lbs / 33.5 kg | 74 lbs / 33.5 kg |
| Leech tension, Maxx cross-cut sail | 74 lbs / 33.5 kg | 76 lbs / 34.5 kg | 77 lbs / 35 kg | 77 lbs / 35 kg | 76 lbs / 34.5 kg |
| Centreboard | Forward | Forward/Middle | Middle | Back | Back |
Trim by condition
- Deck chocks / helm
- Mast back at deck level for more helm in light air; forward to reduce helm as the wind builds. Big deck moves may need a heel change to keep the same leech tension.
- Centreboard
- Fully forward (closer to the mast) in light air; move it aft as the wind increases to reduce helm.
- Sea state
- Lumpy sea: take a chock out. Flat water: add a chock. Aim for balanced helm with good pointing.
- The same text is on North's current page (northsails.com/blogs/north-sails-blog/finn-tuning-guide), but the settings matrix image did not load there, so the numbers come from the 2017 PDF copy hosted by regatta-forum.de.
- The guide doesn't explain exactly how the 'Deck (chocks)' millimetres are measured.
British Finn Association — Newcomer guide: mast, rake and basic settings Undated class web page
- Written for
- Any (general class guide)
- Tension gauge
- Tape rake; mentions that most sailors now use a tension gauge to the sailmaker's leech-tension figure
- How it’s measured
- Prop up the front of the trolley so the transom rests on the ground, hoist a tape to the top band and measure to the cut-out in the aft deck where it meets the transom.
- Source
- British Finn Association, Undated class web page
Base setup
- Starting rake
- 676 cm, then check the leech telltales sailing upwind with the boom on the deck
- Mast numbers
- Measured by supporting the mast at foot and deck ring and hanging 10 kg or 12 kg on the tip (North quotes 10 kg, WB 12 kg); read deflection at ¼, ½ and ¾ length
- Mast stiffness guide (10 kg figures)
- About 108 mm fore/aft at the half point = medium mast for helms around 90 kg; about 100 mm = stiff mast for 100 kg+; ¼ and ¾ figures roughly equal and about 75% of the half-point figure
- Deck ring
- Check the deck-ring height relative to the mast foot when buying a used mast (e.g. a Mk5 Vanguard hull has the ring about 20 mm lower than a modern Devoti)
- Control order on deck
- Front to back: downhaul (cunningham), inhaul, outhaul, kicker
Basic settings by wind (wind in mph)
| Wind (mph) | Mast rake (labelled cm) | Boom to deck (cm) | Boom end vs gunwale | Inhaul (cm) | Outhaul (cm) | Downhaul |
|---|---|---|---|---|---|---|
| 0–8 | 6.74 | 35–25 | Slightly in | 7–5 | 5–7 | None |
| 8–12 | 6.75–6.76 | 25–10 | Slightly in | 5–3 | 6–8 | None |
| 12–16 | 6.77 | 10–0 | Slightly in to level | 3–1 | 5–7 | Slight |
| 16–20 | 6.77 | 0 | Start letting the traveller out beyond the gunwale as wind increases | 2–1 | 6–4 | Slight |
| 20–25 | 6.75–6.76 | 0 | Carry on letting out | 2–1 | 5–3 | Medium |
| 25–30 | 6.75 | 0 | Carry on letting out | 2–3 | 4–2 | Medium |
| 30+ | 6.74–6.75 | 0–5 | Carry on letting out | 2–3 | 2–0 | On hard |
Trim by condition
- Rake
- Rake sets leech tension; the right figure depends on mast stiffness, so treat the table as a start point and log changes.
- Helm balance
- In about force 2–3, boom on the deck and fully powered, with the boat upright: move the whole rig aft for more weather helm or forward for less, aiming for near-neutral helm.
- Centreboard
- Fully forward in light air, moving back as the wind increases to reduce helm.
- The rake row is labelled '(cm)' but the values (6.74–6.77) read as metres, i.e. 674–677 cm, consistent with the 676 cm starting rake in the text.
- Wind is given in mph, not knots. The page doesn't say what the inhaul and outhaul centimetres are measured from.
WB-Sails — WB-Sails Quick Trimguide for FINN Undated (PDF hosted by Finn France, 2022 upload)
- Written for
- WB-Sails Finn mainsail
- Tension gauge
- Tape rake, with an equivalent leech-tension figure in kg (gauge not named)
- How it’s measured
- Table definitions: sheet = boom height above deck; traveller = end of boom to gunwale; inhaul = tack to back side of mast; outhaul = clew to black band.
- Source
- WB-Sails, Undated (PDF hosted by Finn France, 2022 upload)
Base setup
- Deck chocks
- 2.5 cm of chocks behind the mast in the deck ring
- Basic rake
- 678 cm, or 33.5 kg
Settings by wind (rake by tape, cm)
| Setting | 0–5 kn | 5–10 kn | 10–15 kn | 15–20 kn | 20+ kn |
|---|---|---|---|---|---|
| Sheet (boom above deck) | 20–30 cm up | 30–5 cm up | On deck | On deck | 2–5 cm up |
| Traveller (end of boom to gunwale) | 15 cm in | 15 cm in | 7 cm in to 0 | 7 cm outside | 15 cm outside |
| Inhaul (tack to mast) | 3 cm | 2 cm | 0 | 0 | 0 |
| Outhaul (clew to black band) | 3 cm | 7 cm | 5 cm | 2.5 cm | 0 |
| Rake | (675)–678 | 678 | 678–680 | 680–678 | 678–676 |
Trim by condition
- Mast rake
- There is no single right number; adjust it to find the sweet spot for your mast, sail and conditions. Rake controls leech tension: in chop use a softer, more responsive leech, i.e. more aft rake (WB compare the rig to a car's suspension).
- WB say the table values are for reference only and depend on wind and waves.
- The table is an image in the PDF; the values were read from the rendered page (auditor, 2026-11-03). The rake row has no unit (cm, matching the 678 cm base), and the outhaul row header reads 'clew to black board' while the definitions say black band.
US Sailing (author not named) — Finn Tuning Guide 2020 PDF
- Written for
- Not stated (general guide)
- Tension gauge
- Leech-tension gauge (model not named) or tape measure
- How it’s measured
- Centreboard position: lower the board slightly out of the trunk and measure from the board's aft edge to the transom (class minimum 2050 mm, checked with an end-for-end jig). Mast butt: distance from the centreboard pin to the aft face of the mast at the butt, measured with the board fully aft in heavy-air mode. Traveller: where the boom end hits the aft deck.
- Source
- US Sailing (author not named), 2020 PDF
Base setup
- Centreboard range
- Class rules allow 2 cm of forward adjustment from the most aft position; don't go aft of 2051 mm or it will probably measure illegal
- Tiller extension
- Long enough for full hiking with about 30° of helm
- Mast butt
- Measured from centreboard pin to aft face of mast at the butt (no figure given); increase the distance if the boat feels too tight or stiff or the sailor can't hold the hike
Centreboard position (aft edge of board to transom)
| Mode | Aft position | Forward position |
|---|---|---|
| Lightweight sailor and/or stiff boat | 2051 mm | 2071 mm |
| Medium and/or average | 2055 mm | 2075 mm |
| Heavyweight sailor and/or soft boat | 2059 mm | 2079 mm |
Rake, leech tension and traveller by wind
| Condition | Distance (tape) | Leech tension | Traveller (boom end at deck) |
|---|---|---|---|
| No wind | 22′½″ | 69 lbs / 31 kg | Over or outside |
| Light wind | 22′2″ | 73 lbs / 33 kg | Over corner |
| Medium wind | 22′3″ | 75 lbs / 34 kg | 0–4 inches in |
| Heavy wind | 22′2″ | 73 lbs / 33 kg | 0–8 inches out |
Trim by condition
- Medium wind
- Widest range: any time you are hiking but not overpowered with the boom on the deck; in smooth water this can last to nearly 20 kn. In small, short waves the boom can be up to 4″ inside the gunwale, perhaps to 14 kn.
- 6–10 kn
- Get into medium-wind mode as soon as possible; boom on the deck at the gunwale corner or eased up as much as 8″. In waves or slop ease the boom up 8–10″; with a stiff mast never cleat the sheet.
- Under 5 kn
- Aim for the boom parallel to the water without excessive leech tension; vang on only works in smooth water. Use extreme leeward heel if the sail won't hold its shape.
- Heavy wind
- If the boom goes well outside the gunwale on the deck it drops lower, so rake the top aft (butt forward) to avoid adding leech tension. Easing a couple of inches in puffs just bags the sail; steer aggressively, or release about 16″ of sheet so the boom goes out, not up. Raise the board a few inches.
- Inhaul
- Don't pull it tight in breeze (that rounds the entry); ease it until the tack lines up with the luff curve with no wobbles above the tack. A little tighter only in very light, sloppy conditions.
- Outhaul / cunningham
- Set the outhaul after the inhaul, watching the top third of the window and lower batten to flatten the bag; extra tension opens the lower battens in breeze. Cunningham just removes wrinkles until windy, then pull harder to keep the draft forward in the top two battens.
- Downwind
- Play the vang to keep the top batten slightly open; board up as far as you dare, aft corner 4–8″ above the centreboard cap (below halfway in marginal conditions, more than halfway up in big breeze). Fit an outhaul safety so the outhaul only eases 3″ from the upwind setting, and ease all controls before bearing away.
- The 'Distance' values are printed with typographic quote marks (22’½”, 22’2” …); we read them as feet and inches.
- The table follows the guide's rake section, but the PDF doesn't label exactly which points 'Distance' is measured between.
- No author or sail brand is named in the document (US Sailing hosts it).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-03). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Finn resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Finn by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Finn class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational Finn Class Rules, effective date 2025-12-01 (cover; inner title page reads 'Effective date: 1 January 2026'), status Approved
- Class associationfinnclass.org
- Builder specificationsFinn on devotisailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Finn part