One-design race shop · Keelboat

Tartan 10 Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Tartan 10

  • 53 verified parts
  • 11 brands
  • Fit checked Nov 2026

Fit verified for Tartan 10

All Tartan 10 equipment

53 parts

Can’t find a part for your Tartan 10? Request a Tartan 10 part

Official Harken dealer

Tartan 10 deck layout

LOA
33.15 ft (10.10 m)
LWL
27.00 ft (8.23 m)
Beam
9.25 ft (2.82 m)
S.A. (reported)
487.00 ft2 (45.24 m2)
Draft (max)
5.83 ft (1.78 m)
Displacement
7,100 lb (3,221 kg)
Ballast
3,340 lb (1,515 kg)
S.A./Disp.
21.16
Bal./Disp.
47.04
Disp./Len.
161.03

Cunningham

Cunningham — Harken layout for the Tartan 10
Drawing: Harken
  1. 1 57mm Fiddle Block — SwivelHarken 2621 $66.95
  2. 2 40mm T2™ Loop Soft-Attach BlockHarken 2148 $51.95
  3. 6 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  4. 8 57mm T2™ Loop Soft-Attach BlockHarken 2151 $60.95
  5. 15 57mm T2™ Soft-Attach BlockHarken 2152 $53.95
  6. 17 40mm T2™ Soft-Attach BlockHarken 2149 $44.95
  7. 18 Micro Cam-Matic® Kit — Fast Release FairleadHarken 498 $55.95
  8. 19 40mm T2™ Soft-Attach BlockHarken 2149 $44.95
  9. 20 40mm T2™ Soft-Attach BlockHarken 2149 $44.95
  10. 21 40mm T2™ Soft-Attach BlockHarken 2149 $44.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Tartan 10 tuning guide

The Tartan 10 (T-10 class) sails with maximum headstay length and minimum J (maximum rake), so tuning is mostly upper and lower shroud tension, adjustable during races, counted in turns from a Loos Model B base of about 40/22, plus backstay percentage and traveller. North and Doyle split their charts by sea state (flat vs chop), and the older Sobstad and Dieball guides use much higher lower-shroud numbers, so stick with one guide's numbers and gauge.

North Sails — T-10 Tuning Guide and Flat/Chop Water Quick Tuning Charts 2021 guide update; quick tuning charts uploaded January 2021 (the page itself carries a 2017 post date)

Written for
North T-10 main and jibs: paneled AP, 3Di AP and 3Di Light/Wave jibs (named APi-1 and Li-1 in North's January 2021 webinar recap)
Tension gauge
Loos Model B
How it’s measured
J measured from the pin at the bottom of the headstay link plates to the front face of the mast at deck level. Centre the mast to the keel using hull marks equidistant aft of the headstay pin and up from the keel, with a half-full bucket of water on the jib halyard (tape mark 2–3′ above deck). Prebend: main halyard pulled taut to the bottom of the track at the gooseneck, gap measured at the spreaders. Record base stud-to-stud distances with calipers. All turns are from BASE, not from the previous setting.
Source
North Sails, 2021 guide update; quick tuning charts uploaded January 2021 (the page itself carries a 2017 post date)

Base setup

Headstay
Class maximum length (see the class-rules table)
J / mast butt
12′ (class minimum) – with maximum headstay gives maximum rake
Base tension
Uppers 40 / lowers 22 on the Model B, backstay fully off; tip: pull the backstay very hard to make the uppers easier to turn, then release it fully before reading
Prebend
1.5–2″ in the guide text; the quick charts give 1.5″ at base
Spreader marks
Tape on the aft edge at 30″, 31½″ and 33″ from the side of the mast
Jib tracks
53″ apart
Jib lead
Base 14′ 1″ from the headstay pin to the centre of the car sheave; forward only below 5 kn, one hole aft above 15 kn

Flat water quick tuning chart (turns from base; tension on Loos Model B)

Wind (kn)Uppers turnsLowers turnsUppers tensionLowers tensionTraveller from centreBackstay % onPrebend (in)
0–4−2−3—0–6″ twirlMax up02
4–8−1−2—0–4″ twirlMax up01.5
8–12 (base)BASEBASE40226″ up10%1.5
12–162142284″ up25%1
16–20434632Center50%1
20–247647424–6″ down100%1
24+0047426″ down100%1

Chop water quick tuning chart (turns from base; tension on Loos Model B)

Wind (kn)Uppers turnsLowers turnsUppers tensionLowers tensionTraveller from centreBackstay % onPrebend (in)
0–4−3−4—0–6″ twirlMax up02
4–8−2−3—0–4″ twirlMax up01.5
8–12 (base)BASEBASE40226″ up10%1.5
12–1610.541244″ up25%1
16–20324430Center50%1
20–244546384–6″ down100%1
24+0046386″ down100%1

Jib halyard tension (how far the luff wrinkles reach aft)

SailLight/flat 5–8Light/chop 5–8Med/flat 8–15Med/chop 8–15Heavy/flat 15+Heavy/chop 15+
Paneled AP2″ wrinkle6″ wrinkle2″ wrinkle1″ wrinkleTightSmooth
3Di APSmooth1″ wrinkleSmoothSmoothTightTight
3Di Light/WaveSmooth1″ wrinkleSmoothSmoothTightTight

Trim by condition

Light, flat (<8 kn)
Leeward upper snug (some tension, not loose) to keep prebend and limit headstay sag; lowers so the middle of the mast sags about 1″ to leeward when sighting up the slot.
Light, chop (<8 kn)
Leeward upper just going completely loose (under no load, not swinging in 2″ circles); lowers for about 2″ of leeward sag. Only about one full turn looser than flat water. If you need backstay to stop the headstay bouncing, the shrouds are too loose.
Medium (8–15 kn)
Flat: leeward upper snug, about ½″ of leeward sag. Chop: about one turn looser, leeward upper just going loose, lowers slightly tighter so the mast is straight and backstay can be used in puffs without overbend wrinkles.
Heavy (15+ kn)
Leeward upper still under some tension; lowers tight enough that hard backstay flattens the main without inverting it. In chop set the lowers as for flat water but take one full turn off the uppers.
Mainsheet
At max trim the top-batten leech telltale stalls about 20% of the time; in light air or when building speed it flows 80–100%.
Main controls
Light air: small wrinkles along the mast from the halyard; none in medium/heavy. Boom near centreline until overpowered; outhaul so the lowest batten hooks slightly to windward of the boom; vang and backstay on as the wind builds and off when it drops; take the slack out of the backstay in medium air.
Jib sheet
In 10 kn the middle batten is parallel to centreline with the leech at the 30″ mark; trim outside 30″ in light, overpowered or wavy conditions, out to the spreader tip in extreme chop. Cross-sheet from the windward winch.
Quick-chart notes
Set up for the low end of each race's wind range; below-base uppers only in flat water; up to 1″ of leeward sag in light air; straight mast once hiking; when overpowered keep tensioning uppers and set lowers so the main doesn't invert; no jib luff wrinkles above 16 kn; fraculate the mast (jib halyard to the tack) downwind.
Backstay (webinar)
Above base, set about 50% backstay so you can ease it in puffs; if the leeward shrouds go loose, move up one rig setting.
  • Webinar recap used for the backstay note and jib names: https://www.northsails.com/blogs/north-sails-blog/lets-talk-t-10-new-quick-tuning-charts (January 2021).
  • Both quick charts show 0 turns for 24+ kn while listing the same tensions as 20–24 kn; the turn figures in that row look like a misprint.
  • The webinar recap describes base to 16–20 as +3 uppers / +2 lowers, which matches the chop chart rather than the flat chart.
  • The lowers-tension column gives '0–6″ Twirl' and '0–4″ Twirl' in light air instead of a gauge reading; the chart doesn't define 'twirl'.

Evolution Sails — Tartan 10 Tuning 2019 (file name)

Written for
AP and heavy jibs; AP spinnaker and runner
Tension gauge
Not stated
How it’s measured
Turns from base and tension readings.
Source
Evolution Sails, 2019 (file name)

Base setup

Base
7–10 kn: uppers 40 / lowers 25, leads at base, traveller 6″ up
Prebend
2″ at the dock
Lowers check
6″ of swing on the lowers at the dock
Headstay sag
4–5″ sailing upwind
Mast sag
½–1″ to leeward upwind

Tuning chart

TWS (kn)Uppers turnsLowers turnsUppers tensionLowers tensionLeadsTraveller from centreBackstay % onVangJibKite
4–7−2−23520Base or 1 in frontMax upRemove bounceRemove slackAPAP
7–10 (base)004025Base6″ upRemove bounceRemove slackAPAP
10–13214232Base4″ up30–50%SnugAPAP
13–164344381 backCenter50–80%Snug + 1″APAP/Runner
16–206446421–2 back4–6″ down100%Snug + 2″AP/HeavyRunner
20–248548462–3+ back6″+ downMORE!Snug + 3″HeavyRunner

Trim by condition

Tips
Slightly loose beats too tight; overbend wrinkles in the main mean go up a step; if the jib backwinds the main, move the cars back; the backstay is the main gear-change tool.
  • Hosted by the T-10 Class Association.

Quantum Sails — Tartan 10 Quick Tune Updated 9/11/2017

Written for
Not stated
Tension gauge
Not stated (base 40/25)
How it’s measured
Turns from base and tension readings by true wind.
Source
Quantum Sails, Updated 9/11/2017

Base setup

Base
8–10 kn: uppers 40 / lowers 25, traveller 6″ up, backstay 20%

Rig settings

True wind (kn)4–88–1010–1313–1616–2021+
Upper turns−1Base2456
Lower turns−2Base1345
Upper tension374042444648
Lower tension202532384246
TravellerMax up6″ up4″ upCenter4–6″ down6″+ down
Backstay020%30–50%50–80%100%100%
Jib scallops¾″½″¼″¼″SmoothSmooth
Fraculate mastYesYesYesYesYesYes

Trim by condition

Notes
Set up for the low end of the race's wind range; below-base uppers only in flat water (tighten if the forestay bounces); lowers for up to 1″ of leeward sag in light air, straight once everyone is hiking; when overpowered keep tensioning uppers and set lowers so the main doesn't invert with backstay; plenty of mainsheet tension; play the jib sheet with wind and waves.
  • The PDF carries only the Quantum logo artwork; the class site lists it as the Quantum quick tune.

North Sails — Tartan 10 Set-up Matrix (smooth / lump / chop) Undated scanned sheet

Written for
North speed and wave jibs (mini, light and heavy jib battens; light and heavy main battens)
Tension gauge
Loos Model B
How it’s measured
Base uppers 40 / lowers 22; changes are turns from base. Car: F = forward, A = aft, 0 = nominal (14′ 1″ from headstay pin centre to sheave centre). Backstay as % of maximum for the top of the band; traveller in inches up/down from centreline.
Source
North Sails, Undated scanned sheet

Base setup

Base tension
Uppers 40 / lowers 22 (Model B)
Nominal jib car
14′ 1″ (headstay pin to sheave)

Smooth water

Wind (kn)UppersLowersJibCarBackstayMain trav.Battens main / jib
2–5−5−3SpeedF10%+12Light / mini
5–8−3−1Speed020%+10Light / light
8–1100Speed040%+4Light / light
11–14+3+2SpeedA170%−4Light / heavy
14–18+5+3SpeedA190%−8Light / heavy
18–22+7+4SpeedA1100%−10Heavy / heavy
22++8+4SpeedA2Pull harderLowHeavy / heavy

Lump

Wind (kn)UppersLowersJibCarBackstayMain trav.Battens main / jib
2–5−6−4WaveF10%+10Light / mini
5–8−4−2WaveF10%+8Light / light
8–1100WaveF130%+2Light / light
11–14+3+2Wave060%−6Light / heavy
14–18+5+3WaveA180%−10Light / heavy
18–22+6+4WaveA195%−12Heavy / heavy
22++7+5WaveA195%LowHeavy / heavy

Chop

Wind (kn)UppersLowersJibCarBackstayMain trav.Battens main / jib
2–5−6−4WaveF20%+10Light / mini
5–8−4−2WaveF10%+8Light / light
8–11−2−1WaveF130%+2Light / light
11–14+2+1Wave050%−6Light / heavy
14–18+4+2WaveA170%−10Light / heavy
18–22+6+4WaveA190%−12Heavy / heavy
22++7+5WaveA190%LowHeavy / heavy
  • A scanned, undated sheet that uses a two-jib (speed/wave) programme; North's 2021 flat/chop charts are the current North numbers. The class site links this file as 'North T-10 Setup Matrix Flat' (it contains all three sea states) and its 'Setup Matrix Chop' link is the 2021 chop quick chart.

Doyle Sails — Tartan 10 Tuning Guide and T-10 Speed Jib Quick Tuning Matrix Undated (Doyle Boston / Doyle Chicago T-10 team)

Written for
Doyle main; two-jib programme: flatter Speed jib (flat water) and fuller Wave jib (chop)
Tension gauge
Loos Model B
How it’s measured
Square the mast with the main halyard to each chainplate (or a tape to the chainplate pins); bring uppers to 40 with equal turns, re-check, then lowers to 22 with equal turns.
Source
Doyle Sails, Undated (Doyle Boston / Doyle Chicago T-10 team)

Base setup

Forestay
Class maximum for your butt-to-attachment distance (see table)
Base tension
Uppers 40 / lowers 22 – good for about 8–11 kn TWS
Prebend
About 1–1½″ at base
Spreaders
Kicked up slightly, both at the same angle; trim marks taped on
Jib car
Base 14′ 1″ aft of the forestay; drill intermediate holes in the 14′–14′ 6″ zone

Maximum forestay length by butt-to-forestay-attachment distance

Butt to forestay attachmentForestay max
34′ 3″36′ 3″
34′ 4″36′ 3-7/8″
34′ 5″36′ 4-5/8″
34′ 6″36′ 5-1/16″
34′ 7′36′ 5-1/2″

Speed jib quick tuning matrix (turns from base; base 40/22)

Wind (kn)UppersLowersBackstayTravellerJib lead
5−5−30%+12+1
5–8−3−120%+100
8–12402240%+40
12–15+3+270%−4−1
15–18+5+390%−8−1
18–22+7+4100%−10−1
22++8+4110%−10−2

Second matrix in the same file (untitled; followed by a page headed 'T-10 Wave Jib Quick Tuning Guide')

Wind (kn)UppersLowersBackstayTravellerJib lead
5−6−40%+10+2
5–8−4−20%+8+1
8–12−2−130%+2+1
12–15+2+150%−60
15–18+4+270−10−1
18–22+6+490%−12−1
22++7+590%−12−1

Trim by condition

Mast check
Sailing, sight up the back of the mast: the top shouldn't fall off too much and the lower section shouldn't bow to weather.
Main
Hoist to the black band, luff almost smooth. Use the top leech telltale as the sheet reference – occasional stalling means it's right. Over-sheeting locks you in point mode.
Traveller
Light air about 12″ from the top (near the seat corner) with the boom above centreline; mid-track in medium/heavy; keep the boom on centreline until the whole crew is hiking, then work from about 8″ above the bottom of the track so you can dump 8″ in a puff, with the vang on.
Cunningham
Set the main halyard for downwind and use the cunningham upwind; add it as the draft moves aft and when backstay goes on.
Jibs
Wave jib for chop (bow-down mode), Speed jib for flat water (can be in-hauled slightly). A single-jib programme can use the Wave jib with the lead further aft, harder sheet and more headstay tension.
Jib luff
Just enough halyard to remove wrinkles; under-tension rather than over; ease for power in light air.
Crew
Line up from the stanchion behind the chainplates; in very light, choppy air send all but 3 crew below, low and forward.
  • Matrix file: https://ttenclass.com/s/DoyleT10TuningMatrix.pdf. Its 8–12 kn row in the speed-jib table gives the base tensions (40/22) instead of turns. Jib lead units (holes) and the '110%' backstay at 22+ are as printed.
  • Doyle's two matrices closely match North's older smooth and chop set-up matrix.
  • The maximum-forestay table's last row reads 34′ 7′ (as printed).

Dieball Sailing — Tuning Guide Worksheet (T10) Undated

Written for
A/P and heavy headsails; A/P spinnaker
Tension gauge
'Old Loos' (units)
How it’s measured
Butt fixed at 12′0″ and headstay at max throughout; uppers and D1 (lowers) in old-Loos units.
Source
Dieball Sailing, Undated

Base setup

Base (12 kn, bold row)
Butt 12′0″, headstay max, uppers 32, D1 20
Spreader marks
First mark 32″ in from the spreader tip, then marks 2″ outboard and 2″ further outboard

Worksheet (old Loos units)

TWS (kn)ButtHeadstayUppersD1HeadsailSpinnaker
512′0″Max305A/PA/P
612′0″Max325A/PA/P
812′0″Max3210A/PA/P
1012′0″Max3210A/PA/P
12 (base)12′0″Max3220A/PA/P
1412′0″Max3520HeavyA/P
1612′0″Max3525HeavyA/P
1812′0″Max4030HeavyA/P
2012′0″Max4030HeavyA/P
2212′0″Max4035HeavyA/P
2412′0″Max4035HeavyA/P
2712′0″Max4035HeavyA/P

Trim by condition

Light (0–6)
Keep lower tension low – the lowers control forestay tension and you want the forestay as loose as possible; restrain the backstay (shock cord/tape). Allow twist in main and jib (some use the heavy batten to stand the leech out and twist the top). Crew around the shroud base, only helm and trimmer in the cockpit, others to leeward.
Light–medium (6–10)
Trim harder as the breeze builds, easing in big sloppy waves and pressing in flat water; move crew to windward one at a time; tune for the lighter end of the range unless it's building.
Medium–heavy (10–20)
Everyone on the rail; more vang and backstay into the upper teens; keep enough lower tension that extra backstay doesn't wash the main out with overbend wrinkles.
Heavy (20–28)
Max settings on shrouds, vang, cunningham and outhaul.
  • The column headings say 'Butt (cm)' and 'Headstay (cm)' but the entries are 12′0″ and 'Max'.
  • The sheet doesn't say which Loos model the 'Old Loos' units refer to, so its numbers can't be compared directly with the Model B readings in the other guides.

Sobstad — Sobstad T-10 Tuning Guide Undated (older web guide)

Written for
Sobstad Genesis Platinum molded class jib, main and all-purpose spinnaker
Tension gauge
Loos large Model B
How it’s measured
Mast step centred by measuring 14′ aft from the jib tack to each toe rail and across to the step; step the mast all the way forward. Centre with a 100′ tape on the main halyard to toe-rail marks; uppers 5 full turns past hand tight, lowers hand tight plus about 5 turns, then sight straight.
Source
Sobstad, Undated (older web guide)

Base setup

Rake
As far aft as possible: headstay at maximum length (within ¼″, as measurers differ) for your butt-to-attachment distance
Spreader stripe
30″ out from the side of the mast
Jib car
Extra holes drilled between the 2nd and 4th original holes; light–medium air in the 2-1/3 hole

Maximum forestay length by butt-to-attachment distance

Butt to attachment less thanForestay (max) should be
34′ 3″36′ 3″ + 1/2″
34′ 4″36′ 3-7/8″ + 1/2″
34′ 5″36′ 4-5/8″ + 1/2″
34′ 6″36′ 5-1/16″ + 1/2″
34′ 7″36′ 5-1/2″ + 1/2″

Shroud tension guide (Loos large Model B)

True wind (kn)UppersLowers
Drifter 0–54038
Light 5–104438
Medium 10–154545
Heavy 15+4949+

Upwind sail trim

True wind (kn)0–45–910–1415–1920–2425+
Uppers (Loos)4044454949+49+
Lowers (Loos)38384549+49+49+
Jib car (hole)2-1/32-1/33344
Jib luffWrinklesSlight wrinklesNo wrinklesNo wrinklesSmoothSmooth
Jib leech in from spreader tip, flat water33333Working
Jib leech in from spreader tip, with chop01-1/2333Working
Top battenSlightly openSlightly closedSlightly closedSlightly closed / workingOpen / workingOpen
Outhaul4″ shelf3″ shelf2″ shelfNo shelfMaximumMaximum
CunninghamOff – luff wrinklesOff – luff wrinklesSlight wrinklesNo wrinklesMaximum, smooth luffMaximum, smooth luff
BackstayFull offFull offWorking in puffsWorkingMaximumMaximum
Boom positionDown 12″Centre lineCentre lineSlightly below centreDown, workingOn the quarter
Top batten stiffnessSoftSoftStandardStandardStandardStandard
Traveller / vang sheetingTravellerTravellerTravellerBothVangVang

Trim by condition

Shroud notes
0–5: loose lowers help acceleration and loose uppers give headstay sag. 5–10: uppers tighter than lowers for about 1½″ of prebend. 10–15: uppers and lowers equal, backstay and mainsheet for puffs. 15+: both tight; looking up, the masthead falls off at least 6–8″ in a symmetrical curve.
Jib
Light air: ½″ scallops between hanks; jib cunningham tightened until wrinkles disappear from about 10 kn true. Cars back one hole as wind increases, to the 3 hole in heavy air and the 4 hole at 25+. Bring the jib only to the spreader tip out of tacks until up to speed. Lowers must be tight enough to support the headstay.
Main
Halyard at max hoist upwind. Boom near centreline with the top batten parallel; drop the traveller 10″ to accelerate out of tacks; boom to the leeward quarter in very light air (5 kn apparent or less). Flat water 5–20 kn apparent: top telltale flying 50–70% of the time. Chop, disturbed air or 20+ kn apparent: vang-sheet and keep the boat flat.
Spinnaker
Clews even, pole square; on tight reaches lower the pole extra and over-square slightly; reaches to about 80°.
Crew
Usually 7 crew (5 is fine in moderate air, up to 9 in heavy). Upwind in light air, weight to leeward between the shrouds and the 3rd stanchion.
  • An older guide: its lower-shroud numbers are far higher than the current 22 base used by North, Doyle and Quantum.
  • Includes a long deck-layout and running-rigging section (not reproduced).

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Tartan 10 resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Tartan 10 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Tartan 10 class rules before changing equipment, and ask your class measurer if a part is not original equipment.