One-design race shop · Keelboat

Sonar Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Sonar

  • 52 verified parts
  • 11 brands
  • Fit checked Nov 2026

Fit verified for Sonar

All Sonar equipment

52 parts

Can’t find a part for your Sonar? Request a Sonar part

Official Harken dealer

Sonar deck layout

LOA
23'0" (7.0 m)
LWL
19'11" (6.1 m)
BEAM
7'10" (2.4 m)
DRAFT
3'11" (1.2 m)
DISP
2100 lb (950 kg)
BALLAST
900 lb (408 kg)
MAIN & JIB
250 sq ft (23.2 sq m)
SPIN
245 sq ft (22.8 sq m)

Deck layout 1

  1. 1 Standard Cam Base — SwivelHarken 144 $180.95
  2. 2 57mm Ratchet Block — SwivelHarken 2135 $86.95
  3. 3 57mm T2™ Soft-Attach BlockHarken 2152 $53.95
  4. 4 57mm T2™ Soft-Attach BlockHarken 2152 $53.95
  5. 5 57mm T2™ Soft-Attach BlockHarken 2152 $53.95
  6. 6 22mm Car — Stand-Up ToggleHarken 2731 $224.95
  7. 7 22mm Heavy-Duty Endstops — High-Beam, Set of 2Harken 264 $51.95
  8. 8 22mm Heavy-Duty Endstops — High-Beam, Set of 2Harken 264 $51.95
  9. 9 29mm Cheek BlockHarken 350 $18.95
  10. 10 29mm Cheek BlockHarken 350 $18.95

Mainsheet and jib sheet

Mainsheet and jib sheet — Harken layout for the Sonar
Drawing: Harken
  1. 1 40mm Fiddle Block — SwivelHarken 2655 $52.95
  2. 2 29mm Cheek BlockHarken 350 $18.95
  3. 3 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  4. 4 29mm Cheek BlockHarken 350 $18.95
  5. 5 22mm Heavy-Duty Endstops — High-Beam, Set of 2Harken 264 $51.95
  6. 6 29mm BlockHarken 348 $17.95
  7. 7 22mm Car — Stand-Up ToggleHarken 2731 $224.95
  8. 8 22mm Car — Stand-Up ToggleHarken 2731 $224.95
  9. 9 22mm Car — Stand-Up ToggleHarken 2731 $224.95
  10. 10 Standard Cam Base — SwivelHarken 144 $180.95
  11. 11 57mm Ratchet Block — SwivelHarken 2135 $86.95
  12. 12 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  13. 13 29mm Cheek BlockHarken 350 $18.95
  14. 14 29mm Block — Swivel, BecketHarken 341 $33.95
  15. 15 29mm Cheek BlockHarken 350 $18.95
  16. 16 75mm Cheek Ratchamatic® BlockHarken 2682 $171.95
  17. 17 40mm Double Block — SwivelHarken 2638 $86.95
  18. 18 13mm Car — Pivoting ShackleHarken 2700 $150.95
  19. 20 Micro Carbo-Cam CleatHarken 471 $31.95

Deck layout 2

  1. 3 29mm Double Block — SwivelHarken 342 $53.95
  2. 4 29mm Block — SwivelHarken 340 $29.95
  3. 5 29mm Block — SwivelHarken 340 $29.95
  4. 6 29mm Block — SwivelHarken 340 $29.95
  5. 7 29mm Block — SwivelHarken 340 $29.95
  6. 8 29mm T2 Soft-Attach BlockHarken 2146 $29.95

Jib halyard

Jib halyard — Harken layout for the Sonar
Drawing: Harken
  1. 1 29mm Triple Block — SwivelHarken 344 $70.95
  2. 2 29mm Triple Block — Swivel, BecketHarken 345 $74.95
  3. 3 40mm Block — SwivelHarken 2636 $38.95

Deck layout 3

  1. 1 40mm Block — SwivelHarken 2636 $38.95
  2. 2 40mm Double Block — SwivelHarken 2638 $86.95
  3. 3 40mm Block — SwivelHarken 2636 $38.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Sonar tuning guide

The Sonar is tuned mainly with mast blocks at the partners (which set prebend and headstay sag), a fixed upper-shroud tension and loose lowers, then sail controls by wind and sea state. North's guide is the only published sailmaker guide we could find; its shroud figures are pounds on a Loos Model A gauge, not PT-series units.

North Sails — Sonar Tuning Guide Undated web guide (current page)

Written for
North Sonar main, jib (no luff wire) and spinnaker; no model names given
Tension gauge
Loos Model A (uppers in pounds, 5/32″ cable or equivalent)
How it’s measured
Rake is set by forestay length (bearing point of the tee fitting aloft to the centre of the turnbuckle clevis pin). Mast blocking is measured at the aft face of the mast relative to a 'neutral' mark on deck; spreader deflection from the back face of the mast to a line between the spreader-tip holes.
Source
North Sails, Undated web guide (current page)

Base setup

Forestay
25′ 11″, tee-fitting bearing point aloft to centre of the turnbuckle clevis pin
Spreader deflection
2 3/4–3″ (back face of mast to a line between the spreader-tip holes)
Partners
Fit snugly side to side so the mast is centred
Mast step (Ontario boats only)
28 1/4″–28 3/4″, aft face of the mast at the step casting to the lip of the cabin opening
Partner to headstay anchor
Class limit 7′-11.5″ (forward edge of the partner opening to the centre of the headstay anchor)
Neutral / prebend
Centre the mast with the jib halyard, take out the blocks and unpin the lowers, take up backstay until the headstay is just taut and mark the deck at the aft face of the mast. Block behind the mast until it has moved 1″ forward of that mark: this new mark is 'neutral'.
Uppers
230–260 lb on a Loos Model A, tightened equally side to side
Lowers
Loose: you should be able to swing them in 8–10″ circles at shoulder height; fine-tune on the water by sighting up the mast track
Blocks
Six plastic blocks, each 1/2″ wide, cut from a template

Mast blocking: position of the aft face of the mast relative to the neutral mark

WindFlat waterLumpy water
Light air1″ in front of neutral1/2″ in front of neutral
Medium airNeutralNeutral
Heavy air1/2″ behind neutral1″ behind neutral

Mainsail outhaul by wind (relative to the black band)

Wind (kn)Outhaul
0–5Eased 1 1/2″
6–10Eased 1″
11–14Eased 1/2″
15+Maximum

Trim by condition

Blocking logic
Blocks behind the mast (mast forward of neutral) reduce headstay tension and add sag for a deeper, more powerful jib in light air and lumpy water; blocks in front (mast aft) tighten the headstay for a flatter jib in breeze and power up the lower main.
Mainsheet
Top batten parallel to the boom; when up to speed and trying to point, trim a further 2–3″.
Traveller
Boom on centreline up to about 12 kn, then lower the traveller progressively as the wind builds.
Cunningham
New sail: none up to 6 kn; 7–14 kn just enough to take out most wrinkles; progressively tighter above that, and very hard above 18 kn to bring the draft forward up high.
Backstay
Usually little needed; mainly a power control in puffy conditions. More backstay reduces jib luff sag.
Outhaul, off the wind
Ease 1–2″ on reaches and runs.
Leech cord
Just enough to stop flutter in light to moderate wind; tighter in breeze.
Jib lead
Move fore and aft until all three luff telltales lift together when you pinch: upper windward telltale lifting first means move forward, lower first means move aft. Slightly forward in very light air, aft above about 15 kn.
Jib sheet
Upper batten parallel to centreline or slightly to leeward, never hooked to windward (it backwinds the main). With no luff wire, luff sag is controlled by headstay tension via blocks and backstay.
Spinnaker
6–8″ of curl in the luff; pole square to the apparent wind with its outboard end level with the free clew; leeward tweaker on runs to limit leech opening. Over-trimming chokes the slot.
Downwind main
Vang so the top batten is parallel to the boom; ease cunningham, outhaul and backstay.
Steering and crew
The big main means helm balance matters: depower the main in heavy air to cut weather helm. Use crew weight to steer; low and forward in light air, on the windward rail and close together as it builds; fine-tune helm with mainsheet, traveller and backstay.
  • The page carries no date or author.
  • The partner-to-headstay sentence reads 'dance' where 'distance' is clearly meant.
  • Shroud figures are actual pounds on a Loos Model A; don't compare them with PT-1/PT-2 scale readings.
  • The old northsails.com/sailing/en/resources/sonar-tuning-guide address now redirects to the URL above.

Dave Perry — Sonar boat handling and speed thoughts June 2023

Written for
Not sail-specific
Tension gauge
Not stated (no rig tension numbers)
How it’s measured
No rig measurements; set-up, trim and crew-work notes written around match racing in Sonars (it links his dock talk at the 2023 U.S. Youth Match Racing Championship).
Source
Dave Perry, June 2023

Trim by condition

Backstay
Pre-set before the start so it is just snug upwind; no real tension until overpowered, but take up enough slack that the leech doesn't catch and the forestay doesn't pump.
Jib halyard
Err loose with some wrinkles; hoist with some fine-tune on so you can ease it during the beat.
Traveller
All the way up with the boom centred; as you get overpowered, ease down to centreline, add backstay, then ease the traveller below centreline or the sheet. Flat water: hold leech tension and play the traveller. Chop: traveller centred or higher and play the sheet.
Outhaul and vang
Outhaul tight enough to remove the lens foot. No vang upwind, but take up slack when close-hauled so it is set for downwind. When overpowered: more outhaul and downhaul, backstay to just before inversion wrinkles, a little extra vang.
Jib lead
Keep the lower jib slightly full for acceleration out of manoeuvres; above about 10 kn flatten the foot. When overpowered, especially in flatter water, the lead can go back a hole or so.
Crew
Weight forward at all times unless hiking; skipper up by the traveller.
Tacking
Ease the main about 6″ as the boat goes head to wind, then re-trim, so the leech doesn't hook on the backstay.
  • Boat-handling notes by a match-racing coach rather than a sailmaker tuning guide; no shroud, rake or blocking numbers.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Sonar resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Sonar by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Sonar class rules before changing equipment, and ask your class measurer if a part is not original equipment.