One-design race shop · Dinghy

Byte Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Byte

  • 8 verified parts
  • 1 brand
  • Fit checked Nov 2026

Fit verified for Byte

All Byte equipment

8 parts

Can’t find a part for your Byte? Request a Byte part

Official Harken dealer

Byte deck layout

Length
12 ft.
Beam
4 ft 3 in.
Sail Area
58 sq. ft.
Weight (Car Top)
100 lbs.

Vang

Vang — Harken layout for the Byte
Drawing: Harken
  1. 3 29mm Block — Swivel, BecketHarken 341 $33.95
  2. 4 38mm Bullseye FairleadHarken 237 $6.95
  3. 5 40mm Fiddle Block — SwivelHarken 2655 $52.95
  4. 9 Micro Cam-Matic® CleatHarken 468 $36.95
  5. 10 57mm Ratchet Block — SwivelHarken 2135 $86.95
  6. 11 16mm Block — SwivelHarken 417 $31.95
  7. 12 18mm Fly Soft-Attach BlockHarken 2698 $25.95
  8. 13 18mm Fly Soft-Attach BlockHarken 2698 $25.95
  9. 14 18mm Fly Soft-Attach BlockHarken 2698 $25.95
  10. 16 13mm Loop CarHarken 2703 $132.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Byte tuning guide

The Byte CII is unstayed, so tuning is the cunningham, twin-car traveller, mainsheet, outhaul, vang and daggerboard height. What's published is coaching notes rather than sailmaker charts: the builder's 'tuning parabola' for which controls to use in each wind band, plus a racer's article with an outhaul rule of thumb.

Zim Sailing — The Byte CII Tuning Parabola (with 'Depowering the Byte CII Upwind') March 2013 blog posts

Written for
Byte CII class sail
Tension gauge
None (unstayed rig)
How it’s measured
Boom position judged against the back (stern) corner of the boat; twist judged with the top-batten telltale.
Source
Zim Sailing, March 2013 blog posts

Base setup

Sailor weight range
110–160 lb
Fully depowered
Cunningham fully on, windward traveller car fully to windward, boom over the stern corner

The tuning parabola

WindTravellerSailCunningham
LightUpOutOff or variable
MediumDownInVariable
Medium heavy (stronger, heavier sailors up to about 15 kn)DownInStrapped
HeavyUpOutStrapped

Trim by condition

Top-batten telltale
Light and medium air: the '50/50 rule', streaming about half the time and flicking forward the other half.
Boom position
Keep the boom over the back corner of the boat while getting the sail shape you want.
Vang upwind
Not used to depower upwind; just snug it so there's no slack when trimmed in.
Cunningham
The first depowering control: it bends the mast back and to leeward without adding leech tension. It also lets the boom move out, so pull the boom back to the corner.
Traveller
Two cars; in breeze move the windward car to windward.
Mainsheet
Trim only as needed to reach the corner; more sheet loads the leech and powers up.
Daggerboard
If still overpowered, raise it 1" and up to 3" as wind builds; lighter sailors may start at about 15 kn.
  • The depowering details come from the companion post: https://zimsailing.blogspot.com/2013/03/depowering-byte-cii-upwind.html
  • Posted by Zim Sailing's coach (byline not given); also reprinted on sail-world.com.

Zeke Purves-Smith (Sail-World article) — Byte tuning tips 5 June 2012

Written for
Byte class sail
Tension gauge
None (unstayed rig)
How it’s measured
Outhaul judged as a hand width between the boom and the foot.
Source
Zeke Purves-Smith (Sail-World article), 5 June 2012

Trim by condition

Outhaul
Under 15 kn, a hand width between boom and foot; tighten it considerably as the breeze builds, even in chop.
Traveller
Centred in light air; in gusts cleat the main and play the traveller (2:1) to depower instead of using the vang.
Vang downwind
Set so the top batten just begins to bend when you pump.
  • A sailor's article rather than a sailmaker or class guide; most advice is qualitative.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Byte resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Byte by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Byte class rules before changing equipment, and ask your class measurer if a part is not original equipment.